Epson 31-396- Manuals

7 OSCILLATING EDGE SANDER PARTS Fig. 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 1. Fence 2. Table Assembly 3. Cover 4. Miter Gage 5. Back Stop 6. Dust Port 7. 4" Hose Connector 8. Spindle 9. 1½" Dia. Drum 10. 2" Dia. Drum11. 3” Dia. Drum12. 3...

8 ASSEMBLY FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL T H E M A C H I N E I S C O M P L E T E LY A S S E M B L E D A N D Y O U R E A D A N D U N D E R S TA N D T H E E N T I R EINSTRUCTION MANUAL. BELT Fig. 6 Fig. 8 Fig. 9 1. Remove knobs (C) and (D) Fig. 6. 2. Open la...

9 Fig. 10 Fig. 11 6. Slowly release the belt tension lever handle (G) Fig. 10, by grasping the lever handle (G) and pushing it inuntil it stops. 7. Raise the belt guards (E) and (F) Fig. 11. 8. Latch levers (A) and (B) Fig. 11 to belt guards (E) and (F). 9. Replace knobs (C) and (D) Fig. 11, that we...

10 COVER 1. Align the hinges (A) Fig. 14, on the cover, with thehinges (B) on the belt guard. Fig. 14 Fig. 15 2. Insert hinge pins (C) and (D) Fig. 15, through the hinges on the cover and belt guard. Fig. 16 3. Tap the hinge pins in with hammer and rod(supplied). 4. Latch lever (E) Fig. 16 to the co...

11 Fig. 17 Fig. 18 DUST PORT 1. Align the four holes on the dust port (A) Fig. 17, with the four tapped holes (B) on the side of the belt sander. 2. Place a 17/64" flat washer on a 1/4-20x3/8" round head screw, insert the screw through the hole in the dustport, and thread the screw into the ...

14 Fig. 28 12. Assemble appropriate table insert onto the tableusing the three screws that were removed in STEP 10. Fig. 29 Fig. 30 FENCE If sanding with the belt in the horizontal position, the useof the fence is recommended. 1. Place the fence (A) on the table as shown in Fig. 29. 2. Align the slo...

15 OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPINGOSCILLATING EDGE SANDER The power switch is located on the left side of themachine. To turn the machine “ON” press the green startbutton (A) Fig. 31. To stop the machine, push the redstop button (B). There is a stop button located at the top ...

16 Fig. 35 2. Pull out on the table height wheel handle (C) Fig. 35. 3. Rotate table height wheel clockwise to raise the table and counter clockwise to lower the table. 4. When the table height is at the desired position tighten ratchet handles (A) and (B) Fig. 34. TABLE DISTANCE TO BELT Fig. 36 DIS...

17 Fig. 39 ANGLE OF BELT SANDER DISCONNECT MACHINE FROM POWERSOURCE. 1. The belt sander can be tilted from 0 degrees to the table up to 90 degrees to the table. 2. Move the table to the front of the machine. Grasp the tilting handle (C) Fig. 39. GRASP THE TILTING HANDLE FIRMLYWHEN REPOSITIONING THE ...

18 FENCE DISCONNECT MACHINE FROM POWERSOURCE. 1. Loosen fence knobs (A) and (B) Fig. 45. 2. Move fence to desired position and tighten knobs (A) and (B) Fig. 45. Fig. 45 MITER GAGE 1. The miter gage is equipped with adjustable index stops at 90 degrees and 45 degrees right and left.Adjustment to the...

19 OPERATIONS Fig. 47 Fig. 48 The Oscillating Edge Sander can be used to performmany different sanding operations. The followingexamples will show some of the applications that thismachine can be used for. 1. Fig. 48 shows sanding with the fence. Only use the fence when the belt sanderis at 0 degree...

20 Fig. 53 5. Fig. 53 shows the spindle sander being used in the vertical position. It is advisable to raise or lower the tableperiodically to prevent spot wear and improve drum life. STORAGE The Oscillating Spindle Sander has a convenient storagearea for spindles, fence, miter gage, and any otherco...

21 MAINTENANCE DISCONNECT MACHINE FROM POWERSOURCE. 1. Make sure that the belt sander is in the horizontal position as shown in Fig. 55. Fig. 56 Fig. 57 Fig. 55 2. Remove the two screws (A) Fig. 56, on top of the gear box cover (G) Fig. 55. 3. Remove the two screws, located right below screws (A) Fi...

22 REMOVING THE DRUM DISCONNECT MACHINE FROM POWERSOURCE. 1. Open the belt sander guards and remove the sanding belt. 2. Remove nut (A) and washer from the shaft (J) Fig. 59. Fig. 59 3. Insert the two 1/4-20x1-3/4" socket head screws through holes (C) and (D) Fig. 60, on the retraction plate(E)....

23 Printed in U.S.A. Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a De...

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX ® , Fly...

7 OSCILLATING EDGE SANDER PARTS Fig. 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 1. Fence 2. Table Assembly 3. Cover 4. Miter Gage 5. Back Stop 6. Dust Port 7. 4" Hose Connector 8. Spindle 9. 1½" Dia. Drum 10. 2" Dia. Drum11. 3” Dia. Drum12. 3...

8 ASSEMBLY FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL T H E M A C H I N E I S C O M P L E T E LY A S S E M B L E D A N D Y O U R E A D A N D U N D E R S TA N D T H E E N T I R EINSTRUCTION MANUAL. BELT Fig. 6 Fig. 8 Fig. 9 1. Remove knobs (C) and (D) Fig. 6. 2. Open la...

9 Fig. 10 Fig. 11 6. Slowly release the belt tension lever handle (G) Fig. 10, by grasping the lever handle (G) and pushing it inuntil it stops. 7. Raise the belt guards (E) and (F) Fig. 11. 8. Latch levers (A) and (B) Fig. 11 to belt guards (E) and (F). 9. Replace knobs (C) and (D) Fig. 11, that we...

10 COVER 1. Align the hinges (A) Fig. 14, on the cover, with thehinges (B) on the belt guard. Fig. 14 Fig. 15 2. Insert hinge pins (C) and (D) Fig. 15, through the hinges on the cover and belt guard. Fig. 16 3. Tap the hinge pins in with hammer and rod(supplied). 4. Latch lever (E) Fig. 16 to the co...

11 Fig. 17 Fig. 18 DUST PORT 1. Align the four holes on the dust port (A) Fig. 17, with the four tapped holes (B) on the side of the belt sander. 2. Place a 17/64" flat washer on a 1/4-20x3/8" round head screw, insert the screw through the hole in the dustport, and thread the screw into the ...

14 Fig. 28 12. Assemble appropriate table insert onto the tableusing the three screws that were removed in STEP 10. Fig. 29 Fig. 30 FENCE If sanding with the belt in the horizontal position, the useof the fence is recommended. 1. Place the fence (A) on the table as shown in Fig. 29. 2. Align the slo...

15 OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPINGOSCILLATING EDGE SANDER The power switch is located on the left side of themachine. To turn the machine “ON” press the green startbutton (A) Fig. 31. To stop the machine, push the redstop button (B). There is a stop button located at the top ...

16 Fig. 35 2. Pull out on the table height wheel handle (C) Fig. 35. 3. Rotate table height wheel clockwise to raise the table and counter clockwise to lower the table. 4. When the table height is at the desired position tighten ratchet handles (A) and (B) Fig. 34. TABLE DISTANCE TO BELT Fig. 36 DIS...

17 Fig. 39 ANGLE OF BELT SANDER DISCONNECT MACHINE FROM POWERSOURCE. 1. The belt sander can be tilted from 0 degrees to the table up to 90 degrees to the table. 2. Move the table to the front of the machine. Grasp the tilting handle (C) Fig. 39. GRASP THE TILTING HANDLE FIRMLYWHEN REPOSITIONING THE ...

18 FENCE DISCONNECT MACHINE FROM POWERSOURCE. 1. Loosen fence knobs (A) and (B) Fig. 45. 2. Move fence to desired position and tighten knobs (A) and (B) Fig. 45. Fig. 45 MITER GAGE 1. The miter gage is equipped with adjustable index stops at 90 degrees and 45 degrees right and left.Adjustment to the...

19 OPERATIONS Fig. 47 Fig. 48 The Oscillating Edge Sander can be used to performmany different sanding operations. The followingexamples will show some of the applications that thismachine can be used for. 1. Fig. 48 shows sanding with the fence. Only use the fence when the belt sanderis at 0 degree...

20 Fig. 53 5. Fig. 53 shows the spindle sander being used in the vertical position. It is advisable to raise or lower the tableperiodically to prevent spot wear and improve drum life. STORAGE The Oscillating Spindle Sander has a convenient storagearea for spindles, fence, miter gage, and any otherco...

21 MAINTENANCE DISCONNECT MACHINE FROM POWERSOURCE. 1. Make sure that the belt sander is in the horizontal position as shown in Fig. 55. Fig. 56 Fig. 57 Fig. 55 2. Remove the two screws (A) Fig. 56, on top of the gear box cover (G) Fig. 55. 3. Remove the two screws, located right below screws (A) Fi...

22 REMOVING THE DRUM DISCONNECT MACHINE FROM POWERSOURCE. 1. Open the belt sander guards and remove the sanding belt. 2. Remove nut (A) and washer from the shaft (J) Fig. 59. Fig. 59 3. Insert the two 1/4-20x1-3/4" socket head screws through holes (C) and (D) Fig. 60, on the retraction plate(E)....

23 Printed in U.S.A. Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a De...

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX ® , Fly...