Epson 2000P - Stylus Photo Color Inkjet Printer- Manuals

Page 2 - Confidential; The contents of this manual are subject to change without notice.

Confidential Notice:  All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.  The conten...

Page 3 - PRECAUTIONS; DANGER

Confidential PRECAUTIONS Precautionary notations throughout the text are categorized relative to 1)Personal injury and 2) damage to equipment. DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing procedures p...

Page 4 - About This Manual; Manual Configuration; This manual consists of six chapters and Appendix.; CHAPTER 1.PRODUCT DESCRIPTIONS; Provides a general overview and specifications of the product.; CHAPTER 2.OPERATING PRINCIPLES; Describes the step-by-step procedures for the troubleshooting.; CHAPTER 6.MAINTENANCE; Provides information of Stylus Photo R2000; Symbols Used in this Manual

Confidential About This Manual This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given t...

Page 5 - Revision Status; Revision

Confidential Revision Status Revision Date of Issue Description A October 20, 2007 First Release B February 29, 2008 Revised Contents  4.4.4 Lower Housing / Printer Mechanism (p96) Disassembly procedure is revised.  4.4.8 Waste Ink Pad / Waste Ink Tube Left/Right (p110) Description and figure are ...

Page 7 - CONTENTS; Chapter 1 Product Description

EPSON Stylus Photo R1900/R2880/R2000 Revision E 7 Confidential CONTENTS Chapter 1 Product Description 1.1 Product Description ............................................................................................. 10 1.1.1 Features .................................................................

Page 8 - Chapter 5 Adjustment; Product Description

EPSON Stylus Photo R1900/R2880/R2000 Revision E 8 Confidential 4.4.8 Waste Ink Pad / Waste Ink Tube Left/Right ........................................... 1104.4.9 Foot .......................................................................................................... 1114.4.10 PictBridge Hol...

Page 9 - C H A P T E R; PRODUCT DESCRIPTION

Page 10 - Product Description; Item

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description Product Description 10 Confidential 1.1 Product Description 1.1.1 Features EPSON Stylus Photo R1900/R2880/R2000 is a color ink-jet printer that supports A3+ size. The main features are;  High speed & High quality  Maximum prin...

Page 11 - Printing Specifications; Storage Temperature; C A U T I O N; The ink cartridge cannot be refilled.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description Printing Specifications 11 Confidential 1.2 Printing Specifications 1.2.1 Basic Specifications Note *1 : Stylus Photo R2880 has only one slot for black ink cartridge. Switching between the Photo Black and Matte Black can be made by ...

Page 12 - Micro

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description Printing Specifications 12 Confidential 1.2.3 Print Mode  Stylus Photo R1900 Note : The default is indicated by boldface. Note * : cps = character per second Table 1-4. Print Mode (Color) Media Print Mode Resolution (H x V) dpi Dot...

Page 19 - The curve of paper must be 5 mm or below.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description Printing Specifications 19 Confidential Note *1 : “Y” in the “P” column stands for “the paper type/size is Supported”. *2 : “Y” in the “B” column stands for “Borderless printing is available”. *3 : Stylus Photo R2880 only. *4 : Not ...

Page 20 - The printing area for this printer is shown below.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description Printing Specifications 20 Confidential 1.2.5 Printing Area The printing area for this printer is shown below.  Stylus Photo R1900  Stylus Photo R2880 Note * : The margins for Borderless print are margins that bleed off the edges ...

Page 21 - General Specifications; Primary power input; Table 1-11. USB Interface Specifications; Table 1-13. Primary Power Specifications

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description Interface 21 Confidential 1.3 Interface This printer has two USB device ports on the rear side to connect the printer with computers or the like, and one USB host port on the front side to connect an external device such as a DSC (d...

Page 22 - No condensation; Condition; Operating

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description General Specifications 22 Confidential 1.4.2 Environmental Conditions Note *1 : The combined Temperature and Humidity conditions must be within the blue-shaded range in Figure 1-3 . *2 : No condensation *3 : Non-operating with unpac...

Page 23 - The printer has the following four operation buttons.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description Operation Buttons & Indicators (LEDs) 23 Confidential 1.5 Operation Buttons & Indicators (LEDs) 1.5.1 Operation Buttons The printer has the following four operation buttons. 1.5.2 Indicators (LEDs) Eleven indicators (LEDs) a...

Page 26 - Printer Status; Flashes at

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description Operation Buttons & Indicators (LEDs) 26 Confidential Note *1 : When two or more errors occur at the same time, the one with higher priority will be indicated. *2 : The cartridge LED corresponding to each ink cartridge lights. *...

Page 27 - Error

EPSON Stylus Photo R1900/R2880/R2000 Revision E Product Description Operation Buttons & Indicators (LEDs) 27 Confidential 1.5.4 Errors & Remedies Note : For more information on the remedies, see " 3.1.1 Troubleshooting according to Error Messages " (p.34) . Note *1 : When the CDR Tra...

Page 28 - OPERATING PRINCIPLES

Page 29 - Control circuit board; Printer Mechanism; Motor Name

EPSON Stylus Photo R1900/R2880/R2000 Revision E Operating Principles Overview 29 Confidential 2.1 Overview This chapter explains the operating principles of the mechanical sections and electrical circuits in this product. The main components of this product are as follows.  Control circuit board : ...

Page 30 - Printhead Specifications; Line

EPSON Stylus Photo R1900/R2880/R2000 Revision E Operating Principles Printhead Specifications 30 Confidential 2.3 Printhead Specifications The Printhead of this product is a F-Mach head.The following shows the arrangement of the nozzles and the color arrangement of each nozzle line when viewed the P...

Page 31 - Application

EPSON Stylus Photo R1900/R2880/R2000 Revision E Operating Principles PG Setting 31 Confidential 2.4 PG Setting As this printer uses an Auto PG (APG), an appropriate PG position is set according to the used paper type. The following table indicates the PG positions, the main applications of each posi...

Page 32 - Motors

EPSON Stylus Photo R1900/R2880/R2000 Revision E Operating Principles Motors & Sensors 32 Confidential 2.5 Motors & Sensors  Motors  Sensors Figure 2-4. Motors and Sensors Layout Table 2-5. List of Motors Fig. Name Specific A PF Motor Type: DC Motor Drive voltage: 42VDC±5% Armature resistan...

Page 33 - TROUBLESHOOTING

Page 34 - This chapter describes unit-level troubleshooting.; Troubleshooting according to Error Messages

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 34 Confidential 3.1 Overview This chapter describes unit-level troubleshooting. 3.1.1 Troubleshooting according to Error Messages After checking the printer LED and STM3 error indications, you can grasp the fault location using...

Page 37 - Table 3-2. Troubleshooting of Communication Error

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 37 Confidential Table 3-2. Troubleshooting of Communication Error Occurrence Timing Phenomenon Detail Faulty Part/ Part Name Check Point Remedy At power-on The printer does not operate at all. Panel FFC 1. Check that the Panel ...

Page 39 - Table 3-3. Troubleshooting of Printer Cover Open Error

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 39 Confidential At operation Operation at power-on is normal, but the error appears when the print job is sent to the printer. USB 1. Check that the PC and printer are connected via the USB hub. 1. Configure the USB ID setting....

Page 40 - Table 3-4. Troubleshooting of CDR Guide Error

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 40 Confidential Table 3-4. Troubleshooting of CDR Guide Error Occurrence Timing Phenomenon Detail Faulty Part/ Part Name Check Point Remedy At operation CDR Guide Error is indicated on the LED and STM3 when CD/DVD printing is e...

Page 41 - Table 3-5. Troubleshooting of Paper Out Error

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 41 Confidential Table 3-5. Troubleshooting of Paper Out Error Occurrence Timing Phenomenon Detail Faulty Part/ Part Name Check Point Remedy At operation When the Paper Switch is pressed, the LD Roller attempt to feed paper but ...

Page 45 - Table 3-6. Troubleshooting of Paper Jam Error

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 45 Confidential Table 3-6. Troubleshooting of Paper Jam Error Occurrence Timing Phenomenon Detail Faulty Part/ Part Name Check Point Remedy At operation At the time of paper ejection, the PF Roller advances the paper but cannot...

Page 46 - Table 3-7. Troubleshooting of Paper Mismatch Error

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 46 Confidential Table 3-7. Troubleshooting of Paper Mismatch Error Occurrence Timing Phenomenon Detail Faulty Part/Part Name Check Point Remedy During printing Paper Mismatch Error is indicated even the paper path of the media ...

Page 49 - Table 3-11. Troubleshooting of Ink Out Error

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 49 Confidential Table 3-11. Troubleshooting of Ink Out Error Occurrence Timing Phenomenon Detail Faulty Part/Part Name Check Point Remedy During printing After the Carriage has detected the HP, an error is displayed on the LED ...

Page 50 - Table 3-13. Troubleshooting of Maintenance Request

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 50 Confidential At power-on After the Carriage has detected the HP, an error is displayed on the LED and STM3. CSIC FFC 1. Check that the CSIC FFC is connected to the CSIC Board connector and Main Board connector CN22. 1. Conne...

Page 51 - Table 3-14. Troubleshooting of Fatal Error

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 51 Confidential Table 3-14. Troubleshooting of Fatal Error Occurrence Timing Phenomenon Detail Faulty Part/ Part Name Check Point Remedy At power-on At power-on, the CR Motor does not operate at all. CR Motor 1. Check that the ...

Page 60 - Troubleshooting based on Observed Faults; Observed Faults

EPSON Stylus Photo R1900/R2880/R2000 Revision E Troubleshooting Overview 60 Confidential 3.1.2 Troubleshooting based on Observed Faults This section provides troubleshooting procedures based on observed faults such as print quality troubles and abnormal noise. Table 3-15. Print Quality Troubles Obse...

Page 69 - DISASSEMBLY AND ASSEMBLY

Confidential C H A P T E R 4 DISASSEMBLY AND ASSEMBLY

Page 70 - Revision E; Disassembly And Assembly; WARNINGs must be followed to avoid personal injury or death.; W A R N I N G; Tighten screws to the specified torques.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Overview 70 Confidential 4.1 Overview This chapter describes procedures for disassembling and assembling this product. Unless otherwise specified, the disassembled units or main components can be reassembled by reversing the di...

Page 71 - Making a Special Tool for CSIC Board; If using the special tool below, the CSIC Assy (refer to

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Overview 71 Confidential 4.1.2 Tools The following table indicates the tools recommended for use for disassembly, reassembly and adjustment. Note : All of the tools listed above are commercially available. EPSON provides the to...

Page 72 - Classification

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Overview 72 Confidential 4.1.5 Work Completion Checklist Whenever the printer is serviced, use the checklist shown below to confirm all work is completed properly and the printer is ready to be returned to the user. Table 4-3. ...

Page 73 - Closing the CDR Tray Base; Remove the Decoration Plate Right.; Locked

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Overview 73 Confidential 4.1.5.1 Protection for Transportation (Securing the Carriage) (T.B.D) Before packing the printer to be returned to the user, attach several pieces of strong tape to the carriage to prevent damage during...

Page 74 - Figure 4-5. Interference between the Frame and Carriage Unit

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Overview 74 Confidential C A U T I O N When moving the Carriage Unit with the Front Cover and CD- R Tray Base opened, turn the PG CAM (Right) beforehand so that PG++ points downwards to release the PG in order to prevent interf...

Page 75 - C H E C K

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Overview 75 Confidential 4.1.7 Disassembly The flowchart below lists the step-by-step disassembly procedures. When disassembling each unit, refer to the page number shown in the figure. Figure 4-6. Disassembly Flowchart Rear Ho...

Page 76 - Removing the Housings; Figure 4-7. Removing the Paper Support Assy

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Housings 76 Confidential 4.2 Removing the Housings 4.2.1 Paper Support Assy 1. While pulling out the left and right guide pins of the Paper Support Assy, remove the Paper Support Assy. Figure 4-7. Removing the Pape...

Page 77 - Open the Stacker Assy.; Figure 4-10. Reinstalling the Front Decoration Plate Left/Right

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Housings 77 Confidential 4.2.3 Front Decoration Plate Left/Right 1. Open the Stacker Assy. 2. While releasing the hook on the Front Decoration Plate Left, open the plate in the direction of the arrow, and remove it...

Page 78 - Open the Printer Cover.; Figure 4-12. Reinstalling the Rear Housing

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Housings 78 Confidential 4.2.5 Panel Unit 1. Open the Printer Cover. 2. Open the Front Cover and CDR Tray Base. Figure 4-13. Removing the Panel Unit (1)  Align the positioning tabs (one each on the left/right) wit...

Page 79 - Remove the Panel FFC from the Panel Unit.; Route the CDR Sensor cable as shown in the following figure.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Housings 79 Confidential 3. Disengage the nine hooks on the bottom of the Panel Unit, and remove the Panel Unit while pulling out its tab. 4. Remove the Panel FFC from the Panel Unit. Refer to Figure 4-15. 5. Disco...

Page 80 - In the same way, remove the Decoration Plate Left.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Housings 80 Confidential 4.2.6 Decoration Plate Left/Right 1. Remove the Rear Housing. (p.77) 2. Remove the Front Decoration Plate Left/Right. (p.77) 3. Release the three hooks on the front of the Decoration Plate ...

Page 81 - Open the Front Cover and CDR Tray Base.; Figure 4-19. Routing Panel FFC and CDR Sensor Cable

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Housings 81 Confidential 4.2.7 Upper Housing / Printer Cover 1. Remove the Decoration Plate Left/Right. (p.80) 2. Remove the Panel Unit. (p.78) 3. Open the Front Cover and CDR Tray Base. (Refer to 4.1.6 Locking/Unl...

Page 82 - REMOVING THE PRINTER COVER; Remove the Printer Cover Holder Right following the steps below.; into; Be careful not to damage the surface in step 3 and later.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Housings 82 Confidential REMOVING THE PRINTER COVER 1. Remove the Upper Housing / Printer Cover. (p.81) 2. Remove the two C.B.P. M3 x 10 screws that secure Printer Cover Holder Left/Right. Figure 4-20. Removing the...

Page 83 - Remove the two; Figure 4-23. Removing the Upper Housing Support Assy; “Chapter 6; Route the CDR Sensor cable as shown in the figure below.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Housings 83 Confidential 3-3. Slide the Printer Cover Holder Right in the direction of the arrow while pushing the part A, and pull out the Printer Cover Holder Right from the bearing of the Printer Cover. Figure 4...

Page 84 - Removing the Boards; Tighten the screws in the order shown in; Connector

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Boards 84 Confidential 4.3 Removing the Boards 4.3.1 Board Assy (Main Board/Power Supply Board) 1. Remove the Upper Housing / Printer Cover. (p.81) 2. Remove the seven screws (four C.B.S. M3 x 6, two C.B.S. (P2) M3...

Page 85 - Pull out the Board Assy from the Printer.; REMOVING THE MAIN BOARD; Remove the four

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Boards 85 Confidential 4. Pull out the Board Assy from the Printer. Figure 4-27. Removing the Board Assy (2) REMOVING THE MAIN BOARD 1. Remove the Board Assy (Main Board/Power Supply Board). (p.84) 2. Disconnect th...

Page 86 - REMOVING THE POWER BOARD; “Chapter 5

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Boards 86 Confidential REMOVING THE POWER BOARD 1. Remove the Board Assy (Main Board/Power Supply Board). (p.84) 2. Disconnect the Power Board cable from connector CN60 on the Main Board. ( p.85 ) 3. Remove the fou...

Page 87 - Remove the; Attach acetate tape as shown in the figure below.; Do not turn the power on with the Upper Housing removed.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Boards 87 Confidential 5. Remove the C.B.S. (P4) M3 x 8 screw that secures the LED Board, and remove the LED Board. Figure 4-35. Removing the LED Board (3) - 4.3.3 High Voltage Module 1. Remove the Upper Housing / ...

Page 88 - Route the electrode cable as shown in the figure below.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Boards 88 Confidential 3. Pull off the connector of the electrode cable from its terminal on the High Voltage Module Board with long-nose pliers or the like. 4. Disconnect the High Voltage Module cable from connect...

Page 89 - Disassembling the Printer Mechanism; Disconnect the cables from the two APG Sensor connectors.; Referring to

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 89 Confidential 4.4 Disassembling the Printer Mechanism 4.4.1 APG Assy 1. Remove the Upper Housing / Printer Cover. (p.81) 2. Disconnect the APG Motor connector cable from connector CN18 (red...

Page 90 - Release the Carriage Lock, and move the Carriage Unit to the center.; At the position where the tab can be identified through the

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 90 Confidential 4.4.2 CR Scale 1. Remove the Upper Housing / Printer Cover. (p.81) 2. Release the Carriage Lock, and move the Carriage Unit to the center. (Refer to 4.1.6 Locking/Unlocking th...

Page 91 - Stand the coil section.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 91 Confidential 5. Remove the coil section of Torsion Spring 24.7 from the tab on the Left CR Shaft Mounting Plate with tweezers. Figure 4-45. Removing the Torsion Spring 24.7 (1) 6. Remove T...

Page 92 - Pass the CR Scale through the slot on the CR Encoder.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 92 Confidential 4.4.3 Printhead / CSIC Assy 1. Remove the Upper Housing / Printer Cover. (p.81) 2. Release the Carriage Lock, and move the Carriage Unit to the center. (Refer to 4.1.6 Locking...

Page 93 - Figure 4-53. Reinstalling the Ink Cartridge Cover

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 93 Confidential 7. Disengage the two hooks that secure the Ink Guide and remove the Ink Guide from the Cartridge Unit. Figure 4-54. Removing the Ink Guide C H E C K P O I N T The Hinge, Cover...

Page 94 - Disengage the Cable Holder from the hook and remove it.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 94 Confidential 8. Peel off a piece of acetate tape and disconnect the CSIC FFC from the connector on the CSIC Board. 9. Disengage the Cable Holder from the hook and remove it. Figure 4-55. R...

Page 95 - Remove the two Head FFCs from the Printhead.; Confirm that the pad is attached at the position in

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 95 Confidential 11. Remove the three C.B.P. M2.6 x 8 that secure the Printhead using the Phillips Screw Driver, No.1, and vertically lift the Printhead to remove it. Figure 4-57. Removing the...

Page 96 - Figure 4-61. Removing the Lower Housing and Printer Mechanism

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 96 Confidential 4.4.4 Lower Housing / Printer Mechanism 1. Remove the Upper Housing / Printer Cover. (p.81) 2. Disconnect the PictBridge cable from connector CN1 on the Main Board. 3. Disconn...

Page 97 - (Tighten the screws in the order shown in

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 97 Confidential 8. Lift the Printer Mechanism grasping it by the holding positions with your hands, and remove it from the Lower Housing. C A U T I O N When performing the following step, mak...

Page 99 - Figure 4-68. Removing the Left Frame Support Plate

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 99 Confidential 6. Remove the two C.B.S. M3 x 6 screws that secure the Frame Support Plate (Left), and remove it. Figure 4-68. Removing the Left Frame Support Plate 7. Remove the foot of Left...

Page 100 - Figure 4-72. Removing CR Shaft Mounting Plate Fixed Spring; and the tab on the Drive Pulley Holder with needle-nose pliers.; Figure 4-74. Removing the Driven Pulley Holder

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 100 Confidential 9. Remove CR Shaft Mounting Plate Fixed Spring from the tab and notch on the Main Frame, and pull out the spring in the direction of the arrow. Figure 4-72. Removing CR Shaft...

Page 101 - Remove the CR Drive Belt from the CR Motor Pinion Gear.; Figure 4-77. Rotating the Left Parallelism Adjust Bushing

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 101 Confidential 12. Remove the CR Drive Belt from the CR Motor Pinion Gear. Figure 4-75. Removing the CR Drive Belt 13. Remove the four C.B.S. (P4) M3 x 6 screws that secure the CR Guide Pla...

Page 102 - Carriage Shaft with tweezers.; Figure 4-79. Removing the Carriage Shaft Spacer; Left CR Shaft Mounting Plate from the Carriage Shaft.; Figure 4-80. Removing the Left CR Shaft Mounting Plate; and Left PG Cam from the Carriage Shaft.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 102 Confidential 16. Lift the Carriage Shaft upwards, and remove the Carriage Shaft Spacer from the Carriage Shaft with tweezers. Figure 4-79. Removing the Carriage Shaft Spacer 17. Rotate th...

Page 103 - Figure 4-84. Rotating the Right CR Shaft Mounting Plate

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 103 Confidential 20. Pull the Right CR Shaft Mounting Plate away from the tab on the Main Frame and rotate toward you. Figure 4-84. Rotating the Right CR Shaft Mounting Plate 21. Slide the Ca...

Page 104 - from the Carriage Unit.; Figure 4-87. Removing the Belt Holder Mounting Plate; Remove the Belt Holder from the Carriage unit.; Set the longer end of the Carriage Shaft to the left side.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 104 Confidential 22. Turn the Belt Holder Mounting Plate in the direction of the arrow, and remove it from the Carriage Unit. Figure 4-87. Removing the Belt Holder Mounting Plate 23. Remove t...

Page 105 - the Sensor FFC from the Carriage Unit, and remove the Carriage Unit.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 105 Confidential 25. Disconnect the Sensor FFC from the connector on the CR Encoder Board, pull out the Sensor FFC from the Carriage Unit, and remove the Carriage Unit. Figure 4-90. Removing ...

Page 106 - Remove the Printer Mechanism.; Secure the two Earth cables together with the screw.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 106 Confidential 4.4.6 ASF Assy 1. Remove the Printer Mechanism. (Refer to 4.4.4 Lower Housing / Printer Mechanism (p.96)) 2. Remove the C.B.S. M3 x 8 screw that secures the Earth cables on t...

Page 107 - Figure 4-95. Removing the Guide Roller LD; remove the ASF Assy from the Printer Mechanism.; When only removing the ASF Assy, you do not need to perform

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 107 Confidential 9. Remove the two C.B.S. M3 x 6 screws that secure the two Guide Roller LDs. 10. Gently pull the LD Roller Shaft to the rear of the printer, and remove the Guide Roller LDs. ...

Page 109 - NG

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 109 Confidential 4.4.7 Front Paper Guide Pad 1. Remove the Printer Mechanism. (Refer to 4.4.4 Lower Housing / Printer Mechanism (p.96)) 2. Remove the Front Paper Guide Pads and Front Paper Gu...

Page 110 - Figure 4-102. Positions of Waste Ink Tubes

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 110 Confidential 4.4.8 Waste Ink Pad / Waste Ink Tube Left/Right 1. Remove the Printer Mechanism. (Refer to 4.4.4 Lower Housing / Printer Mechanism (p.96)) 2. Remove the C.B.P. M3 x 8 screw t...

Page 111 - Figure 4-104. Removing the PictBridge Holder Assy

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 111 Confidential 4.4.9 Foot 1. Remove the Printer Mechanism. (Refer to 4.4.4 Lower Housing / Printer Mechanism (p.96)) 2. Remove the six foot at the backside of the Lower Housing. Figure 4-10...

Page 112 - Base; Release the Front Cover from the two guide pins of the CDR Tray Base.; Figure 4-106. Screws that Secure the Paper EJ Frame Assy

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 112 Confidential 4.4.11 Paper EJ Frame Assy / Front Cover / CDR Tray Base 1. Remove the Upper Housing Support Assy. (p.83) 2. Release the Front Cover from the two guide pins of the CDR Tray B...

Page 113 - Base in the direction of the arrow.; Adjustment

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 113 Confidential 9. Remove the C.B.S. M3 x 6 screw that secures the Right CDR Tray Base Support, and remove the Right CDR Tray Base Support. Figure 4-108. Remove the CDR Tray Base Support 10....

Page 115 - Remove the Spur Gear 68 from the Paper EJ Roller Shaft.; Figure 4-116. Removing the Left CDR Release Lever Sub Assy; Align the Shaft and Bushing.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 115 Confidential 6. Remove the Spur Gear 68 from the Paper EJ Roller Shaft. Figure 4-115. Removing the Spur Gear 68 7. Remove the C.B.P. M3 x 6 screw that secures the Left CDR Release Lever S...

Page 116 - Remove the Right CDR Release Lever Sub Assy.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 116 Confidential 4.4.13 Ink System Unit 1. Remove the Right CDR Release Lever Sub Assy. (Refer to 4.4.12 CDR Release Lever Sub Assy (p.114)) 2. Release the Carriage Lock, and move the Carriag...

Page 117 - Figure 4-122. Screws that Secure the Ink System Unit

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 117 Confidential 6. Remove the two C.B.S. M3 x 6 screws that secure the Ink System Unit. Figure 4-122. Screws that Secure the Ink System Unit 7. Remove the two C.B.S. M3 x 6 screws that secur...

Page 118 - Figure 4-125. Removing the Ink System Unit

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 118 Confidential 8. Remove the Ink System Unit downwards from the Main Frame keeping the Unit from coming in contact with the Paper EJ Transmission Lock Lever. Figure 4-125. Removing the Ink ...

Page 119 - Front Paper Guide Pad Tray

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 119 Confidential 4.4.14 Front Paper Guide / Paper EJ Roller / Front Paper Guide Pad Tray 1. Remove the Paper EJ Frame Assy / Front Cover / CDR Tray Base. (p.112) 2. Release the Carriage Lock,...

Page 120 - Return the Carriage Unit to its home position.; Figure 4-133. Removing the Front Paper Guide and Paper EJ Rollers; Guide and remove the Left Front Frame.; Figure 4-135. Removing the Front Paper Guide Pad Tray

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 120 Confidential 7. Return the Carriage Unit to its home position. 8. Remove the C.B.S. M3 x 6 screw that secure the Left Front Frame. 9. Release the tab that secures the Front Paper Guide fr...

Page 121 - DISASSEMBLING THE FRONT PAPER GUIDE PAD TRAY; Remove the three Waste Ink Pads from the Front Paper Guide Pad Tray.; Figure 4-137. The PF Roller Shaft and the bushing of the Front

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 121 Confidential DISASSEMBLING THE FRONT PAPER GUIDE PAD TRAY 1. Remove the Front Paper Guide Pad Tray in the direction of the arrow. (p.120) 2. Remove the three Waste Ink Pads from the Front...

Page 123 - Figure 4-141. Removing the PF Grounding Spring

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 123 Confidential 5. Remove the PG Grounding Spring from the notch on the Main Frame, and remove the PF Grounding Spring from the groove on the PF Roller Shaft. Figure 4-141. Removing the PF G...

Page 124 - Figure 4-146. Removing the PF Roller Shaft; Figure 4-145. Handling the PF Roller Shaft; Figure 4-147. Handling the PF Roller Shaft

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 124 Confidential 9. Remove the PF Roller Shaft from the Bushings on the Rear Paper Guide and the Center Support, slide the PF Roller Shaft to the left to remove it from Right Bushing 8, and r...

Page 125 - Figure 4-148. Removing the Release Holder Assy

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 125 Confidential 4.4.16 Release Holder Assy 1. Remove the APG Assy. (p.89) 2. Release the PE Sensor connector cable from the five tabs on the Release Holder Assy. 3. Remove the three C.B.S. M...

Page 126 - Figure 4-151. Removing the FLAG Release Assy

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 126 Confidential 4.4.17 FLAG Release Assy 1. Remove the APG Assy. (p.89) . 2. Remove the Release Holder Assy. (p.125) 3. Remove the guide pin on the Driven Release Holder from the Main Frame ...

Page 127 - Figure 4-152. Attaching the Perforated Sheets and the LD Cover

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 127 Confidential 4.4.18 Upper Paper Guide Assys 1. FLAG Release Assy (p.126) 2. Remove the PE Sensor Holder. (p.135) 3. Pass a sheet of A3 size paper into the gap between the Upper Paper Guid...

Page 128 - Figure 4-154. Removing the Upper Paper Guide Torsion Spring; , and remove the Upper Paper Guide Assys to the rear.; Figure 4-156. Removing the Upper Paper Guide Assy; Upper Paper Guide Assy:

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Disassembling the Printer Mechanism 128 Confidential 4. Remove the six Upper Paper Guide Torsion Springs from the tabs on the Main Frame, and pull out the Upper Paper Guide Torsion Springs from the six Upper Paper Guide Assys. ...

Page 129 - Removing the Motors; Figure 4-157. Removing the CR Motor Connector Cable

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Motors 129 Confidential 4.5 Removing the Motors 4.5.1 CR Motor 1. Remove the Upper Housing / Printer Cover. (p.81) 2. Release the Carriage Lock, and move the Carriage Unit to the center. (Refer to 4.1.6 Locking/Unl...

Page 132 - Removing the Sensors; Figure 4-164. Removing the CR Encoder Sensor Board; Disconnect the FFC from the PF Encoder Sensor Board.; Figure 4-165. Removing the FFC and the Screw that Secures

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Sensors 132 Confidential 4.6 Removing the Sensors 4.6.1 CR Encoder 1. Remove the Carriage Shaft / Carriage Unit. (p.98) 2. Remove the two C.B.P. M2.6 x 5 screws that secure the CR Encoder Sensor Board. 3. Disconnec...

Page 133 - Figure 4-166. Removing the PF Encoder Sensor Holder

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Sensors 133 Confidential 4. While pressing the guide pin on the PF Encoder Sensor Holder using tweezers, slide the holder upwards to release the three tabs, and remove the PF Encoder Sensor Holder. Figure 4-166. Re...

Page 134 - Make sure that the FFC is routed as shown in

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Sensors 134 Confidential 4.6.4 CDR Sensor 1. Remove the Paper EJ Frame Assy / Front Cover / CDR Tray Base. (p.112) 2. Disengage the two hooks that secure the CDR Sensor and remove the CDR Sensor. Figure 4-170. Remo...

Page 135 - Figure 4-172. Removing the PE Sensor Holder

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Sensors 135 Confidential 4.6.5 PE Sensor Holder 1. Remove the APG Assy. (p.89) 2. Remove the PE Sensor connector cable from the five tabs on the Release Holder Assy and the two tabs on the Head Cable Cover. Figure ...

Page 136 - Figure 4-174. Removing the Cover Open Sensor

EPSON Stylus Photo R1900/R2880/R2000 Revision E Disassembly And Assembly Removing the Sensors 136 Confidential 4.6.6 Cover Open Sensor 1. Remove the Panel Unit. (p.78) 2. Remove the C.B.P. M3 x 8 screw that secures the Cover Open Sensor and remove the Cover Open Sensor. Figure 4-174. Removing the Co...

Page 137 - ADJUSTMENT

Page 138 - Adjustment Items and Overview

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment Items and Overview 138 Confidential 5.1 Adjustment Items and Overview This chapter describes adjustments to be made after the disassembly/reassembly of this product. 5.1.1 Servicing Adjustment Item List The items, purposes and out...

Page 141 - Priority

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment Items and Overview 141 Confidential 5.1.2 Required Adjustments The table below lists the required adjustments depending upon the parts being repaired or replaced. Find the part(s) you removed or replaced, and check which adjustmen...

Page 144 - PF Motor

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 144 Confidential 5.2 Adjustment This section explains the adjustments that do not use the Adjustment Program. 5.2.1 PF Belt Tension Adjustment When either of the following parts has been removed or replaced, this adjustment must b...

Page 145 - Print Head

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 145 Confidential 8. Press the [MEASURE] button. (“----” is displayed on the LCD screen.) 9. Put the tip of the tweezers on the Drive Belt, and flip it downward in that position. The “----” displayed on the LCD will become wave pat...

Page 146 - Install the printer on a level base.; Figure 5-5. Setting the Parallelism Adjust Bushing

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 146 Confidential 5.2.2.1 PG Adjustment Method 1. Install the printer on a level base. 2. Connect the Tester to the printer frame and Adjustment Gauge. Figure 5-4. Connecting the Tester 3. Load unused Ink Cartridges of all colors i...

Page 147 - of the Upper Paper Guide.; PG Standard Value

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 147 Confidential 6. With its conductor connection portion up, set the Adjustment Gauge in the specified position (on the left side of the Front Paper Guide).  Setting PositionRear direction: Match the rear end of the Gauge with t...

Page 148 - specified position (on the right side of the Front Paper Guide).; Figure 5-10. Setting the Adjustment Gauge; Figure 5-9. Relationship between Parallelism Adjust Bushing

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 148 Confidential 9. Lower the Gear of the Parallelism Adjust Bushing on the left side of the frame stepwise, and confirm continuity. When continuity is confirmed, define the position where the Gear was raised one step up from the ...

Page 149 - Move the Carriage Unit onto the Adjustment Gauge.; PF Roller Shaft Center Support Position; and Level Block

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 149 Confidential 12. Move the Carriage Unit onto the Adjustment Gauge.  Moving positionMatch the right end of the Gauge with the right end of the Carriage Unit. Figure 5-11. Moving the Carriage Unit 13. Return the PG position to ...

Page 150 - Support Position; Figure 5-14. Center Support Bushing Cam and the Screw

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 150 Confidential 5.2.3.1 How to Adjust the PF Roller Shaft Center Support Position 1. Before performing this adjustment, remove the following parts:  Lower Housing (Refer to 4.4.4 Lower Housing / Printer Mechanism (p96) )  ASF A...

Page 151 - end of Upper Paper Guide; Adjustment Resolution: 50; must be set to compensate for the thickness of the coating; Figure 5-16. Positional Relationship between Center Support

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 151 Confidential 5. Set the jig in place on the PF Roller Shaft as shown in the figure below.  Left side: Inside of PF Roller left end (E-ring)  Right side: Clearance between PF Roller right end (Right Bushing 8) and left end of...

Page 152 - Figure 5-17. Outside the Specified Value Range

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 152 Confidential Figure 5-17. Outside the Specified Value Range Figure 5-18. Inside the Specified Value Range Unevenness

Page 153 - Figure 5-19. The Calibrator and the Accessories

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 153 Confidential 5.2.4 Colorimetric Calibration This calibration is performed to compensate the ink discharge amount when the following parts are replaced:  Print Head  Main Board  PS Board The following tools are used for this...

Page 154 - Figure 5-20. Concept of Remaining Ink Amount; Conventional Head ID adjustment

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 154 Confidential  Supplement: Regarding remaining ink amountWhen the Ink Counter detects ink out, a certain amount (safety margin) of ink is still remaining in the cartridge to prevent the print head from damages caused by printi...

Page 155 - Figure 5-22. Printing and checking a nozzle check pattern

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 155 Confidential 5.2.4.2 Adjusting Method of the Colorimetric Calibration The following illustrates the overall workflow. Figure 5-21. Overall Workflow 1. Connect the printer and the calibrator with the PC to which the Colorimetri...

Page 156 - Figure 5-23. Printing a Calibration Chart

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 156 Confidential 5. Load one sheet of A4 or letter-size Archival Matte Paper/Enhanced Matte paper to print the Calibration Chart. Figure 5-23. Printing a Calibration Chart Figure 5-24. Illustration of Calibration Chart 6. After th...

Page 157 - Figure 5-28. Preparing the Calibration Chart; Rows that have not been measured are displayed in pale color.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 157 Confidential 8. Place the Calibrator on the calibration plate, and click [Calibrate] Figure 5-27. Preparing the Calibrator 9. After confirming that you are within the color measurement time limit, place the Calibration Chart s...

Page 158 - Be sure to start the measurement from the top side of the chart.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 158 Confidential 11. Click [Next], and write the Color ID to the printer. After the writing has finished, the Colorimetric Calibration Tool automatically checks the Color ID. Figure 5-30. Writing of Color ID 12. When the following...

Page 159 - ASF Guide Roller LDs Position Adjustment; After installing the

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 159 Confidential 5.2.5 ASF Guide Roller LDs Position Adjustment When installing the Guide Roller LDs, the position of the Guide Roller LDs must be adjusted so that the positions of the LD Roller Shaft and Retard Roller are optimiz...

Page 160 - Aligning the Position of the Guide Roller LD (0 Digit Side); Figure 5-35. Checking the Position of Tab on the Guide Roller LD; The following are the possible troubles for misadjustment.; Tab Position; Above upper limit

EPSON Stylus Photo R1900/R2880/R2000 Revision E Adjustment Adjustment 160 Confidential 3. Light the printer's inside through a gap between the Roll Paper Frame and the ASF Assy with a penlight, and look the tab on the Retard Roller Holder at the back of the two reference tabs on the ASF Assy through...

Page 161 - MAINTENANCE

Page 163 - Protection Counters Upper Limit; Table 6-1. List of Waste Ink Pads to be replaced; Parts name

EPSON Stylus Photo R1900/R2880/R2000 Revision E Maintenance Overview 163 Confidential 6.1.2.2 Maintenance Request Waste ink is discharged to Waste Ink Pads via the Cap Unit. The printer has counter function that counts how much waste ink is held in the Waste Ink Pads and stores the value in the EEPR...

Page 164 - Type

EPSON Stylus Photo R1900/R2880/R2000 Revision E Maintenance Overview 164 Confidential 6.1.3 Lubrication The lubrication used for the components of the printer has been decided on based on evaluation carried out by Epson. Therefore, the specified amount and places of lubrication given in this section...

Page 165 - A little at 4 points

EPSON Stylus Photo R1900/R2880/R2000 Revision E Maintenance Overview 165 Confidential Figure 6-3. Lubrication (3) Figure 6-4. Lubrication (4) Figure 6-5. Lubrication (5) Figure 6-6. Lubrication (6) <Lubrication Point> Contact point of the CR Scale Mounting Plate (Left/Right) and the Main Frame...

Page 166 - The Driven Pulley Holder

EPSON Stylus Photo R1900/R2880/R2000 Revision E Maintenance Overview 166 Confidential Figure 6-7. Lubrication (7) Figure 6-8. Lubrication (8) Figure 6-9. Lubrication (9) Figure 6-10. Lubrication (10) Figure 6-11. Lubrication (11) <Lubrication Point> Contact point of the rear side of CR Guide P...

Page 167 - Lubrication Type

EPSON Stylus Photo R1900/R2880/R2000 Revision E Maintenance Overview 167 Confidential Figure 6-12. Lubrication (12) Figure 6-13. Lubrication (13) 6.1.3.1 Lubrication of Carriage Shaft 1. Fit the Carriage Unit onto the Carriage Shaft, and move it to the center of the Shaft. 2. Using a syringe, lubric...

Page 168 - Figure

EPSON Stylus Photo R1900/R2880/R2000 Revision E Maintenance Overview 168 Confidential 3. Hold the Carriage Unit, and while turning the Carriage Shaft clockwise and counterclockwise, move the Carriage Unit to spread the grease evenly. Figure 6-15. Lubricating the Carriage Shaft (2) 4. Move the Carria...

Page 169 - Repeat

EPSON Stylus Photo R1900/R2880/R2000 Revision E Maintenance Overview 169 Confidential 7. Hold the Carriage Unit, and while turning the Carriage Shaft, move the Carriage Unit to the right end of the Carriage Shaft to lubricate the grease evenly. Figure 6-18. Lubricating the Carriage Shaft (5) 8. Repe...

Page 170 - APPENDIX

Page 171 - Connector Summary; Table 7-1. Connection of the Major Components; This manual does not provide exploded diagrams or parts list.

EPSON Stylus Photo R1900/R2880/R2000 Revision E Appendix Connector Summary 171 Confidential 7.1 Connector Summary This section shows the connections between the main components of the printer. Table 7-1. Connection of the Major Components 7.2 Exploded Diagram / Parts List This manual does not provid...

Page 173 - Product Description; Features

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Product Description 173 Confidential 8.1 Product Description The Stylus Photo R2000 is inkjet color printer, and it was made based on the mechanism of the Stylus Phoro R1900.Therefore, this chapter describes the specification and the funct...

Page 174 - Paper Support & Stacker are closed

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Features 174 Confidential 8.2 Features  Casing specifications  Network interface  Ink cartridge  Nozzle configration  Ink scrambling sequence  Operation buttons & indicators 8.2.1 Casing specifications  Dimensions :622.1 mm (W) ...

Page 175 - Table 8-4. Available Channels and Standard

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Features 175 Confidential 8.2.2 NetWork Interface Stylus Photo R2000 can be connected to the network via Wired LAN or Wireless LAN connection. (They can not be used simultaneously.) The following describes each Interface.  Wired LAN The f...

Page 176 - Switching Wired/Wireless LAN; MCS Index; Table 8-6. Wireless LAN Setting from the Control Panel; Setting from Control Panel

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Features 176 Confidential Table 8-5. Communication Speed for 802.11n * 1 * 2 MCS : Modulation and Coding Scheme GI : Guard Interval Note *1 : After the decimal point is displayed by the 0.5Mbps.Number in parentheses is defined value of 802...

Page 177 - Color

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Features 177 Confidential 8.2.3 Ink Cartridge Describes the specification of the ink cartridge.  Product numbers of the EPSON ink cartridges  Shelf life Two years from production date (if unopened), six months after opening package.  St...

Page 179 - Button

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Features 179 Confidential 8.2.6 Operation Buttons & Indicators (LEDs)  Operation Buttons This printer has the following six operation buttons.  Indicators (LEDs) Thirteen indicators (LEDs) are provided to indicate settings or printer...

Page 180 - Operation Buttons & LEDs Functions

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Features 180 Confidential  Operation Buttons & LEDs Functions Note " * " : The paper cannot be fed or ejected if the CDR Tray Base is open. Table 8-13. Operation Button Functions Button Printer Status Function Power Off • Tuns...

Page 183 - Disassembly

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Disassembly 183 Confidential 8.3 Disassembly 8.3.1 Summary This section describes changed parts & new parts for Stylus Photo R2000 only. For assembling of other parts, please refer to the information of Stylus Photo R1900/R2880. ( "...

Page 186 - Secure the Panel FFC with double-sided tape as follows.

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Disassembly 186 Confidential  Panel Unit 1. Remove the screws (C.B.P 3x10) (x2)that secure the Panel Unit. Figure 8-7. Remove the Panel Unit (1) 2. Disconnect the Panel FFC and CDR Sensor cable from the Panel Board. Figure 8-8. Remove the...

Page 187 - Tab hole

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Disassembly 187 Confidential  Decoration Plate Left/Right 1. For Decoration Plate Right, Disengage front of the hook (x1) , and lift the Decoration Plate Right while disengaging bottom of the hooks (x2). 2. In the same way, remove the Dec...

Page 188 - Remove the Upper Housing / Printer Cover; Wireless LAN Board Assy; Tighten the screws in the order show in

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Disassembly 188 Confidential  Upper Housing / Printer Cover 1. Remove the screws (C.B.P 3x10) (x6) that secure the Upper Housing, and lift the Upper Housing/Printer Cover. Figure 8-11. Remove the Upper Housing / Printer Cover  Wireless L...

Page 189 - Refer to; Wireless LAN

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Disassembly 189 Confidential 3. Disconnect the Wireless LAN Board cable, and remove the Wireless LAN Board Assy. Figure 8-14. Remove the Wireless LAN Board Assy (3)  Board Assy (Main Board / Power Supply Board)  For disassembling the Boa...

Page 190 - MAC address setting

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Adjustment 190 Confidential 8.4 Adjustment 8.4.1 Summary This section describes new adjustment items & changed adjustment items for Stylus Photo R2000 only. For other adjustment items, please refer to the information of Stylus Photo R1...

Page 191 - Required Adjustments

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Adjustment 191 Confidential 8.4.3 Required Adjustments The table below lists the required adjustments depending upon the parts being repaired or replaced. Find the part(s) you removed or replaced, and check which adjustment(s) must be carr...

Page 192 - ASF Assy

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Adjustment 192 Confidential Note : “O” indicates that the adjustment must be carried out. “---” indicates that the adjustment is not required. If you have removed or replaced multiple parts, make sure to check the required adjustments for ...

Page 193 - Figure 8-15. MAC Address Setting Flowchart; MAC address example:; END; START

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Adjustment 193 Confidential 8.4.4 Adjusment Procedure  Mac address setting <Overview> This printer have a network function and stores there MAC address (Media Access Control Address) in the EEPROM on the Network Board. The Network B...

Page 194 - Start the adjustment program.

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Adjustment 194 Confidential <Setting procedure> 1. Start the adjustment program. 2. Select the “Initial Setting” from the menu. The initial setting screen appears. 3. Enter the last six digits of MAC address into the MAC address entr...

Page 195 - Table 8-18. Support Paper for Colorimetric Calibration; Multi Sensor Adjustment (Ink Mark Sensor Adjustment); Purpose; Nozzle Check Pattern

Stylus Photo R1900/R2880/R2000 Revision E Stylus Photo R2000 Adjustment 195 Confidential  Colorimetric Calibration The procedure of this adjustment is same as Stylus Photo R1900 / R2880. Refer to " 5.2.4 Colorimetric Calibration " (p.153) . But, support paper for Calibration Chart is differ...