Clarity Cordless Telephone - Manuals

Page 2 - TABLE OF CONTENTS

TABLE OF CONTENTS Important Safety Instructions ................................ 3Features ............................................................ 8Choosing a Location ......................................... 10Telephone Installation ........................................ 12Handset Battery ....

Page 9 - Emergency Buttons

FEATURES 10 1 2 3 5 6 7 8 9 11 12 13 14 4 15 16 Handset 1. Neckloop Jack 2. Handset Volume 3. Boost 4. Dial Pad 5. Emergency Buttons 6. Talk 7. Channel 8. Memory 9. Flash 10. Mute 11. Redial/Pause 12. Handset Ringer Off/ Vibe/On 13. Handset Tone 14. Belt Clip 15. Headset Jack 16. Antenna/Visual Ring...

Page 10 - CHOOSING A LOCATION

Connecting telephone line cord CHOOSING A LOCATION 1. This phone requires a modular phone jack (RJ11C) and a standard 120V AC wall outlet.2. Plug the AC Adapter directly into outlet. 3. Do not plug other appliances into the same outlet or have outlet controlled by a wall switch.4. Choose a location ...

Page 11 - CONNECTING YOUR TELEPHONE

Connecting AC Adapter CONNECTING YOUR TELEPHONE Carefully remove your cordless telephone from its box. If there is any visible damage, do not attempt to operate this equipment. Return it to the place of purchase. Check to be sure that you have all items that come with your telephone. You should have...

Page 14 - HANDSET BATTERY INSTALLATION

base of the phone downward to secure it on the wall. 5. Plug the adapter into a standard AC power (electrical) outlet. 6. Press and lift out the handset holder tab, turn it around so the narrow tab end extends out and slide back into its slot. This will hold the handset in the cradle when the phone ...

Page 16 - Low Battery; about; Battery Life

Low Battery When the handset battery gets low, there will be two (2) beeps every thirty (30) seconds. If the battery becomes low while you are on a call, you will be disconnected after about two (2) minutes. Terminate the call and recharge the battery. To recharge the battery pack, place the handset...

Page 17 - BOOST – Clarity Power On/Off; Talk button

TELEPHONE HANDSETDigital Clarity Power Technology With Digital Clarity Power, the high frequency sounds are amplified more than the low frequency sounds so words are not just louder, but clearer and easier to understand. It also provides intelligent amplification to make soft sounds audible, while k...

Page 23 - To Install Battery Back-up Batteries; To Replace Battery Backup Batteries; Disconnect telephone line cord and remove desk/

To Install Battery Back-up Batteries 1. Disconnect telephone line cord and remove desk/ wall mount bracket from telephone base.2. Disconnect battery back-up connector from the telephone base.3. Install four (4) AA Alkaline batteries with negative (-) end of battery touching the spring.4. Connect bat...

Page 28 - Adding a Memory Location; number to insert a pause. Refer to the Pause Feature; Dialing a Memory Location

Adding a Memory Location 1. Unit must be in standby mode only.2. Press the MEM button.3. Enter the telephone number you wish to store.4. Press the MEM button.5. Press the number on the dial pad that you wish to store the number to.6. A long beep will indicate the programming process is complete.Duri...

Page 29 - process is complete.; Dialing an EMERGENCY Number; The C4205 has been designed to give you years of

3. Enter the telephone number you wish to store.4. Press the MEM button.5. Press the emergency button on the dial pad that you wish to store the number to.6. A long beep will indicate the programming process is complete. Dialing an EMERGENCY Number 1. Press the TALK button.2. Press the EMERGENCY key...

Page 30 - • Reset the security code by placing the handset; The phone does not ring when you receive a call:; • Make sure the RINGER switch on the handset

TROUBLESHOOTINGThe unit will not operate/no dial tone: • Verify the TALK Button is lit.• Verify the AC Adapter is securely plugged into AC outlet, the base and the telephone.• Verify the telephone line cord is securely plugged into the wall jack and the telephone.• Make sure the base antenna is in a...

Page 31 - Try unplugging a few devices.; Noise, Static, Interference or Other Calls Heard while; the wall outlet with other appliances.; Phone Will Not Hold Charge:; • Make sure the charging contacts on the

plugged into the wall jack and the telephone.• Make sure you are in the usable range of the base station.• You may have too many extensions on your line. Try unplugging a few devices. Noise, Static, Interference or Other Calls Heard while Using the Handset: • Try changing channels.• Make sure the ba...

Page 32 - Handset Battery Charging); Difficulty in Placing or Receiving Calls:; wall outlet with other appliances. Disconnect for

• If necessary, replace the handset battery. (See Handset Battery Charging) Difficulty in Placing or Receiving Calls: • Move closer to the base and try again.• If moving closer does not work, you may have lost the security code.• Reset code by placing the handset back on the base for 5-10 seconds. (...