Clarity D722 - Manual - manualsarea.com

Page 2 - TABLE OF C ONTENTS

1 Important Safety Instructions.........................................................4 INSTALLATION Installing your phone - Base............................................................8Installing batteries - Handset...........................................................9 OVERVIEW Handset ...

Page 4 - IMPORTANT SAFETY INSTRUCTIONS

4 5 Privacy of communications may not be ensured when using this phone. Warning: To maintain the compliance with the FCC’s RF exposure guideline, place the base unit at least 20 cm from nearby persons.Warning: To reduce the risk of fire or injury to persons, read and follow these instructions. 1. Re...

Page 5 - BATTERY SAFETY INSTRUCTIONS; Location; PACKAGING C ONTENTS/LOCATION

6 7 cause temporary or permanent damage to your hearing. Although there is no single volume setting that is appropriate for everyone, you should always use your telephone with the volume set at moderate levels and avoid prolonged exposure to high volume sound levels. The louder the volume, the less ...

Page 6 - ) Always use the cables provided in the box.; Use only NiMH rechargeable batteries.; INSTALLING YOUR PHONE; INSTALLING/CHARGING BATTERIES; Do not place the films within reach of small children!

8 9 1) Plug the power supply & line cord into the base station.2) Plug the other end of power supply & line cord into the wall socket, as shown. 3) Always use the cables provided in the box. 1) Slide out the battery compartment cover.2) Place the two batteries as indicated. Follow the polari...

Page 7 - ID history, press to delete and individual entry.; HANDSET OVERVIEW

10 11 HANDSET OVERVIEW 1. RD/P (REDIAL / PAUSE) • In idle mode, press repeatedly to view the last numbers dialed • While entering numbers, press and hold to insert a dialing pause (P) 2. AUDIO BOOST During a call, press to enhance the clarity and loudness of your caller’s voice. 3. MUTE / X (REMOVE)...

Page 10 - HANDSET SCREEN IC ONS; MENU STRUCTURE; HANDSET MENU STRUCTURE

16 17 The screen display gives you information on the current status of the telephone. The speakerphone is turned on. While reviewing the call list history, missed calls that have not been reviewed. The ringer is switched off. New voicemail received from the telephone service provide (network subscr...

Page 11 - Keystroke Table; Characters by number of key presses; HANDSET - TEXT ENTRY TABLE

18 19 The following table shows you where each letter and punctuation character can be found. This will be helpful when storing a name in the directory. In editing mode, a cursor is displayed to indicate the current text entry position. It is positioned at the right of the last character entered. Wr...

Page 12 - HANDSET AUDIO OPERATIONS; USING YOUR PHONE

20 21 Volume Control (earpiece and speakerphone) During a call:Press <UP/DOWN> to increase or decrease the listening volume. The current setting is shown. When the volume reaches the minimum or maximum setting, you hear two beeps. When you end the call, the setting will remain at the last sele...

Page 15 - Add a New Directory Entry; DIRECTORY

26 27 Transfer an External Call from Handset to HandsetDuring an external call: 1. Press <MENU/SELECT>, then <UP/DOWN> to select Intercom .2. Press <MENU/SELECT>: • If you have two handsets, the outside call is put on hold and your handset screen shows Calling other handset . The o...

Page 18 - Reasons for missing caller ID information; View the Call Log Entries; CALLER ID DISPLAY

32 33 CALLER ID DISPLAY (NETWORK DEPENDENT) This product supports caller ID services offered by most telephone service providers. If you have subscribed to Caller ID service, and provided the identity of the caller is not withheld, the number of the caller will be displayed together with the date an...

Page 21 - BASE SETTINGS

38 39 Program the Direct Memory Keys on base There are four direct memory keys on the base, which share the same phone number with Speed Dial locations under keys 0 through 3 on the handset. The corresponding relastion is as follows: Direct memory key M0 = Speed Dial location for key "0" on ...

Page 23 - My telephone doesn’t work at all; I cannot dial out; I cannot get a dial tone; TROUBLESHOOTING

42 43 If you have difficulty with your telephone, please try the suggestions below. My telephone doesn’t work at all • Make sure the power cord is securely plugged in. • Make sure that the battery connector is securely plugged into the cordless handset. • Make sure the telephone line cord is securel...

Page 24 - My cordless handset does not ring when I receive a call

44 45 "Out of range or no pwr at base" appears on my cordless handset • Ensure that the telephone base is powered up. • Place the cordless handset in the telephone base for one minute to allow the cordless handset and base to synchronize. • Move the cordless handset closer to the telephone b...

Page 25 - My caller ID isn’t working; My telephone does not receive caller ID when on a call; New voicemail; ADDITIONAL HANDSETS

46 47 My caller ID isn’t working • Caller ID is a subscription service. You must subscribe to this service from your telephone service provider for this feature to work on your telephone. • Your caller must be calling from an area that supports caller ID. • Both your and your caller’s telephone serv...

Page 26 - Weight; BOTH; TECHNICAL INFORMATION

48 49 • D722™ - 30dB • D724™ - 40dB Dimensions • Handset Size: 7” x2 1/4” x 1 1/2” (H x W x D) • Base Size: 3 1/4” x 5 3/4” x 4” (H x W x D) Weight • Handset Weight: 6.125 oz. (with batteries) • Base Weight: 8.25 oz. Power Requirements: • AC Adapter: Input: 100V - 240V, 200mA Output: 6VDC, 450 mA • ...

Clarity D722 - Manual

Table of Contents:

Summary

Other Clarity Models