Canon MF5950dw - Manuals

<< Previous Next >> 8 Selecting a method for connecting to the wireless LAN Two methods are provided for connecting to the wireless LAN or access point, connecting using WPS (Wi-Fi Protected Setup) function or connecting manually.Select the appropriate setting method after checking the f...

<< Previous Next >> 9 Configuring with WPS Features Is there a WPS button ? No YES Set the machine’s PIN code using “WPS PIN Code Mode” that is entered manually from the computer to the wireless LAN router or access point. Click Here Connect using “WPS Push Button Mode.” Click Here

Configuring with WPS Features (Pin Code Mode) 15 << Previous Next >> Enter the PIN code generated by the imageCLASS device to wireless LAN routers and/or access points for connection. 1. Press [ ] (Menu). 2. Select <Network Settings> using [ ] or [ ], and then press [OK]. 3. Select...

20 Configuring Manually If your wireless LAN routers and/or access points do not support WPS, enter the wireless LAN router and/or access point information to the machine for connection. Select Access Point From the list of access points searched by the machine, select a wireless LAN router or an ac...

21 Configuring Manually << Previous Next >> Preparing The following information is required.Check your wireless LAN routers and/or access points, and make a note of the information labeled on the bottom. * See the manual provided with your wireless LAN routers and/or access points, or co...

22 Configuring Manually (Required Information) Access Point Name/Network Name * It may be labeled as “SSID.” It is the distinguished name for specifying a particular access point.It is used for selecting an access point. Network Key *It is also called encryption key, WEP key, WPA/WPA2 passphrase, PS...

23 Configuring Manually (Using the Wireless Setup Assistant) Using the Canon MF/LBP Wireless Setup Assistant You can check the information for the wireless LAN router or access point (such as SSID or Network Key) by using the Canon Wireless Setup Assistant.You need to have this information when usin...

27 Configuring Manually (Selecting Access Points) From the list of access points searched by the imageCLASS device, select a wireless LAN router or an access point to be connected and enter a network key for connection. Selecting Access PointFor selecting access points, WEP 802.11 authentication sys...

32 Configuring Manually (Selecting Access Points) 9. Enter the network key that you have written down. ASCII text 1. Press [ ] (Tone), and the select <Entry Mode>.2. Enter the network key. Enter it using the numeric keys.3. Select <Apply> using [ ] or [ ], and then press [OK]. Hexadecima...

36 Configuring Manually (Manually Entering SSID) 1. Press [ ] (Menu). 2. Select <Network Settings> using [ ] or [ ], and then press [OK]. 3. Select <Wireless LAN Settings> using [ ] or [ ], and then press [OK]. 4. Press [OK]. << Previous Next >>

37 Configuring Manually (Manually Entering SSID) 5. Select <SSID Settings> using [ ] or [ ], and then press [OK]. 6. Select <Manual Settings> using [ ] or [ ], and then press [OK]. 7. Enter the SSID that you have written down. After entering it using the numeric keys, select <Apply>...

40 Configuring Manually (Manually Entering SSID) 10. Select the entry format that matches the number of network key characters (digits) that you have written down, using [ ] or [ ]then press [OK]. Either of the following screens is displayed. << Previous Next >>

41 Configuring Manually (Manually Entering SSID) 11. Enter the network key that you have written down earlier ASCII text 1. Press [ ](Tone), and then select <Entry Mode>.2. Enter the network key, using the numeric keys.3. After entering, select <Apply> using [ ] or [ ], and then press [O...

45 Checking IP Address Settings 1. Press [ ] (Status Monitor/Cancel). Follow the steps below to confirm the IP address set on the imageCLASS device. Write down the IP address as you may need it when installing the software. Checking IPv4 address settings 2. Select <Network Information> using [...

47 Preparing to the install the software Before installing the software drivers will need to be downloaded for the components you wish to install. Drivers are available

48 Installing the Printer Driver Before using the printer you must install the UFR II printer driver for it. Important If an older version of the printer driver has been installed, uninstall the older version before installing the new version. 1. Double-click the Printer Driver .dmg to display it’s ...

54 Installing the Fax Driver 1. Double-click the Fax Driver .dmg to display it’s contents. Before using the fax, you must install the fax driver for it. Important: • If a older version of the fax driver has been installed, uninstall the older version before installing the new version. • Close all ap...

60 Installing the Scanner Driver 1. Double-click the Scanner Driver .dmg to display it’s contents. Note: Before installing. • Perform the following procedures. -Exit running applications.-Remove the USB cable that connects the computer and the scanner. When an older version of the scanner driver is ...

66 Adding the Printer in the System Preferences 1. Open [System Preferences] then click [Print & Fax] or [Print & Scan]. The [Print & Fax] or [Print & Scan] dialog box is displayed. << Previous Next >>

72 Adding the Fax in the System Preferences 1. Open [System Preferences] then click [Print & Fax] or [Print & Scan]. The [Print & Fax] or [Print & Scan] dialog box is displayed. << Previous Next >>

79 Registering the Scanner to the MF Toolbox 1. Double-click the icon of [MF Toolbox] installed in the following folder. To scan documents via network connection, you need to register the scanner to the MF Toolbox. The hard disk you are using >[Applications]>[Canon MF Utilities]. 2. Click [Net...

83 Congratulations! You have successfully added your Canon imageCLASS device to your wireless network. << Previous End