Canon LBP3200 - LBP 3200 B/W Laser Printer- Manuals

Contents 5.2 Countermeasures ............................................................................................................................................... 5- 2 5.2.1 Image Faults ..........................................................................................................

Chapter 1 1-1 1.1 PRODUCT SPECIFICATIONS 1.1.1 Product Specifications 0002-6360 Body installation method Desk-top page printer Photosensitive medium OPC drum Exposure method Semi-conductor laser Development method Toner projection Transfer method Roller transfer Separation method Curvature/bias on s...

Chapter 1 1-3 1.2 Detailed Specifications 1.2.1 Printing Speed 0002-6870 T-1-1 (unit: sheets/min)*If "LGL" is indicated in the cassette, you can load the legal-size in the cassette. 1.2.2 Stack Upon Delivery 0002-6888 T-1-2 Fixing mode Paper size P l a i n paper P l a i n paper L H e a v y p...

Chapter 1 1-5 1.3 NAMES OF PARTS 1.3.1 External View 0002-9016 <Front View> F-1-1 T-1-3 <Rear View> [1] Face-down delivery tray [5] Cassette [2] Face-down delivery area [6] Manual feed slot [3] Delivery selection cover [7] Paper guide [4] Power switch [8] Front cover A5 A4 LTR LG L ON B5...

Chapter 1 1-7 1.4 SAFETY 1.4.1 Safety of Laser Light 0002-4309 Laser radiation could be hazardous to the human body. For this reason, laser radiation emitted inside this machine ishermetically sealed within the protective housing and external cover. No radiation can leaak from the machine in thenorm...

Chapter 1 　 1-8 F-1-4 1.4.4 Safety of Toner 0002-4556 The machine's toner is a non-toxic material composed of plastic, iron, and small amounts of dye. Do not put the toner into fire. It may explode. Toner on the Skin or Clothes1. If your skin or clothes came into contact with toner, use dry tissue t...

Chapter 2 2-1 2.1 LASER EXPOSURE SYSTEM 2.1.1 Overview/Configuration 2.1.1.1 Overview 0002-4749 F-2-1 T-2-1 The machine's laser scanner assembly consists of the laser driver and the scanner motor, which are driven by signalscoming from the engine controller.The laser driver serves to turn on the las...

Chapter 2 2-3 2.2 IMAGE FORMATION SYSTEM 2.2.1 Overview/Configuration 2.2.1.1 Overview 0002-8228 F-2-2 T-2-2 In response to a print command, the engine controller turns on the main motor to drive the photosensitive drum,developing cylinder, primary charging roller, and transfer charging roller.There...

Chapter 2 2-5 2.3 PICKUP AND FEEDING SYSTEM 2.3.1 Overview/Configuration 2.3.1.1 Overview 0002-8681 F-2-3 T-2-3 [1] Cassette feed [11] Face-down delivery roller [2] Cassette pickup roller [12] Face-down delivery [3] Separation pad [13] Main motor [4] Manual feed [14] Cassette pickup solenoid [5] Fee...

Chapter 2 　 2-6 Pickup and Feed Operation (from the cassette) If the cassette paper sensor detects the presence of paper while the absence of paper is identified in the manual feedpickup assembly, the machine picks up paper from the cassette.When the main motor operates and the cassette pickup solen...

Chapter 2 2-7 Initial Jam The top sensor or the delivery sensor goes on while the main motor is starting to rotate. Cover Open Jam The machine identifies a condition in which the front cover is opened while it is moving paper. 2.3.2.2 Delay Jams 2.3.2.2.1 Pickup Delay Jam 0002-8760 If the top sensor...

Chapter 2 2-9 2.4 FIXING SYSTEM 2.4.1 Overview/Configuration 2.4.1.1 Overview 0002-8375 F-2-4 T-2-4 The machine's fixing system is an on-demand type, and its fixing assembly consists of the fixing film unit and thepressure roller: the fixing film has a built-in fixing heater, thermistor, and thermal...

Chapter 2 　 2-10 2.4.2 Various Control Mechanisms 2.4.2.1 Protective Functions 2.4.2.1.1 Protective Mechanisms 0002-8543 The machine is equipped with the following 3 types of protective mechanisms used to prevent its fixing heater fromgoing awry. 1. protective mechanism by the CPU2. protective mecha...

Chapter 3 3-1 3.1 EXTERNAL AND CONTROLS SYSTEM 3.1.1 Rear Cover 3.1.1.1 Removing the Cassette 0002-3466 1) Remove the cassette by holding the cassette handle. 3.1.1.2 Removing the Rear Cover 0002-3475 1) Open the face-up cover [1], and remove the left/ right shaft [2]; then, detach the face-up cover...

Chapter 3 　 3-2 the front cover has already been removed.) 2) Free the 2 claws [1], and detach the top cover [2]. F-3-5 3.1.2.4 Removing the Right Cover 0002-3493 1) Remove the screw [1].2) Free the claw [2] at the rear; then, free the claw [4] at the front bottom as by sliding the bottom of therigh...

Chapter 3 3-3 F-3-9 3.1.3.4 Removing the Left Cover 0002-3501 1) Remove the screw [1].2) Free the claw [2] at the rear; then, free the claw [4] at the front bottom as by sliding the bottom of theleft cover [3] to the front. 3) While opening the bottom of the left cover [3] slightly toward the outsid...

Chapter 3 　 3-4 F-3-13 3.1.5 Front Cover 3.1.5.1 Removing the Front Cover 0002-3448 1) Open the front cover [1], and free the claw [2] of the arm to separate. 2) Remove the left/right shaft [3], and detach the front cover. F-3-14 3.1.6 Engine controller board 3.1.6.1 Removing the Cassette 0002-3581 ...

Chapter 3 3-5 F-3-17 3.1.6.4 Removing the Left Cover 0002-3586 1) Remove the screw [1].2) Free the claw [2] at the rear; then, free the claw [4] at the front bottom as by sliding the bottom of theleft cover [3] to the front. 3) While opening the bottom of the left cover [3] slightly toward the outsi...

Chapter 3 　 3-10 3.1.8.9 Removing the High- Voltage Power Supply Board 0002-3749 1) Remove the flat cable [1].2) Remove the 3 screws [2], and detach the high- voltage power supply board [3]. F-3-39 3.1.9 CAPT board 3.1.9.1 Removing the Cassette 0002-3591 1) Remove the cassette by holding the cassett...

Chapter 3 3-11 F-3-43 3.1.9.5 Removing the CAPT Board 0002-3596 1) Removing the flat cable [1].2) Remove the 3 screws [2], and detach the CAPT board [3]. F-3-44 3.1.10 Top sensor 3.1.10.1 Removing the Cassette 0002-3757 1) Remove the cassette by holding the cassette handle. 3.1.10.2 Removing the Fro...

Chapter 3 3-13 F-3-51 3.1.10.8 Removing the Power Supply Assembly 0002-3778 1) Remove the 3 screws [1].2) Disconnect the 4 connectors [2], and free the flat cable [3] of the engine controller board. F-3-52 3) Push down the front of the power supply assembly [2] while feeding the left/right boss [2];...

Chapter 3 　 3-16 3.2 IMAGE FORMATION SYSTEM 3.2.1 Transfer Charging Roller 3.2.1.1 Removing the Transfer Charging Roller 0002-3718 1) Open the front cover.2) Pick the 2 claws [1] on the right side of the roller, and lift it. 3) Slide the transfer charging roller [2] to the right to detach. F-3-61 [1...

Chapter 3 3-17 3.3 LASER EXPOSURE SYSTEM 3.3.1 Laser Scanner Unit 3.3.1.1 Removing the Cassette 0002-3683 1) Remove the cassette by holding the cassette handle. 3.3.1.2 Removing the Rear Cover 0002-3684 1) Open the face-up cover [1], and remove the left/ right shaft [2]; then, detach the face-up cov...

Chapter 3 3-19 3.4 PICKUP AND FEEDING SYSTEM 3.4.1 Cassette Pickup Roller 3.4.1.1 Removing the Cassette 0002-3510 1) Remove the cassette by holding the cassette handle. 3.4.1.2 Removing the Front Cover 0002-3513 1) Open the front cover [1], and free the claw [2] of the arm to separate. 2) Remove the...

Chapter 3 3-21 F-3-75 2) Remove the spring [1].3) While freeing the claw, detach the tooth-missing gear [2]. F-3-76 3.4.1.9 Removing the Cassette Pickup Roller 0002-3565 1) Shift down the main unit so that its front faces down (i.e., the inside of the main unit is in view). 2) Remove the boss of the...

Chapter 3 　 3-22 F-3-79 4) Remove the 2 claws [1] and remove the cassette separation pad [2] by sliding it up. F-3-80 3.4.3 Cassette Pickup solenoid 3.4.3.1 Removing the Cassette 0002-3511 1) Remove the cassette by holding the cassette handle. 3.4.3.2 Removing the Front Cover 0002-3514 1) Open the f...

Chapter 3 　 3-24 F-3-87 3.4.3.8 Removing the Power Supply Assembly 0002-3753 1) Remove the 3 screws [1].2) Disconnect the 4 connectors [2], and free the flat cable [3] of the engine controller board. F-3-88 3) Push down the front of the power supply assembly [2] while feeding the left/right boss [2]...

Chapter 3 　 3-26 F-3-95 3.4.4.6 Removing the Left Cover 0002-3694 1) Remove the screw [1].2) Free the claw [2] at the rear; then, free the claw [4] at the front bottom as by sliding the bottom of theleft cover [3] to the front. 3) While opening the bottom of the left cover [3] slightly toward the ou...

Chapter 3 3-29 3.4.5.9 Removing the Main Motor 0002-3780 1) Shift down the main unit so that its front faces down (i.e., the inside of the main unit is in view). 2) Remove the 2 screws [1], and detach the main motor [2]. F-3-108 3.4.6 Multi-purpose Pickup Roller 3.4.6.1 Removing the Cassette 0002-36...

Chapter 3 　 3-32 F-3-122 3.4.7 Multi-purpose Pickup Solenoid 3.4.7.1 Removing the Cassette 0002-3697 1) Remove the cassette by holding the cassette handle. 3.4.7.2 Removing the Front Cover 0002-3699 1) Open the front cover [1], and free the claw [2] of the arm to separate. 2) Remove the left/right s...

Chapter 3 　 3-36 3.5 FIXING SYSTEM 3.5.1 Fixing Pressure Roller 3.5.1.1 Removing the Cassette 0002-3720 1) Remove the cassette by holding the cassette handle. 3.5.1.2 Removing the Front Cover 0002-3722 1) Open the front cover [1], and free the claw [2] of the arm to separate. 2) Remove the left/righ...

Chapter 3 　 3-38 controller board, and free the cable from the cableclamp. 4) Disconnect the connector [2] of the power supply board. 5) Remove the left/right pressure spring and grounding spring [3]. 6) Remove the left/right pressure plate [4]. F-3-145 7) While holding the left/right frame [2] of t...

Chapter 3 　 3-40 F-3-153 3.5.2.6 Removing the Left Cover 0002-3729 1) Remove the screw [1].2) Free the claw [2] at the rear; then, free the claw [4] at the front bottom as by sliding the bottom of theleft cover [3] to the front. 3) While opening the bottom of the left cover [3] slightly toward the o...

Chapter 4 4-1 4.1 Periodically Replaced Parts 4.1.1 Parts Requiring Periodical Replacement 0002-4267 The machine does not have parts that require periodical replacement.

Chapter 4 　 4-2 4.2 Consumables 4.2.1 Consumable 0002-4308 T-4-1 Work by Item Interval (guide) User EP-26 toner cartridge every 2500 prints (approx.) Service technician None

Chapter 4 4-3 4.3 Periodical Service 4.3.1 Items Requiring Scheduled Servicing 0002-4268 The machine does not have items that require scheduled servicing.

Chapter 4 　 4-4 4.4 Cleaning 4.4.1 Items Requiring Cleaning 0002-4316 T-4-2 Before starting cleaning work, be sure to turn off the power and disconnect the power plug to avoid fires andelectric shocks. Work by Item Intervals User External covers As needed (when soiled) Service technician Cassette pi...

Chapter 4 4-7 4.5 Lubrications 4.5.1 Areas Requiring Application of Grease 0002-4235 The machine has areas that require grease to permit smooth movement of parts or ensure good electrical conductivity.If you have replaced a part in these areas or if you have removed the grease, be sure to apply grea...

Chapter 4 　 4-8 F-4-3 4.5.3 Fixing Drive Transmission Gear 0002-4240 Area of application: [1]Grease: MOLYKOTE EM-50LAmount: 10 +/-5 mgLocation of application:- 2 locations on gear butting ribs in opposition- spread in circumferential direction over a length of 1/4 or more F-4-4 4.5.4 Large Gear Bush...

Chapter 4 4-9 F-4-5 4.5.5 Large Gear 0002-4249 Area of application: [1]Grease: MOLYKOTE EM-50LAmount: 20 +/-10 mgLocation of application:- rib against which gear is butted- spread in circumferential direction over a length of 1/2 or more F-4-6 4.5.6 Feed Gear 0002-4250 Area of application: [1]Grease...

Chapter 4 　 4-10 F-4-7 4.5.7 Internal Gear 0002-4251 Area of application: [1]Grease: MOLYKOTE EM-50LAmount: 40 +/-10 mgLocation of application:- 5 teeth or more of internal gear in opposition- 2 locations in circumferential direction F-4-8 4.5.8 Large Gear Deceleration Gear/Plate R 0002-4252 Area of...

Chapter 4 　 4-12 4.5.10 Drive Releasing Arm 0002-4256 Area of application: [1]Grease: MOLYKOTE EM-50LAmount: 10 +/-5 mgLocation of application:- 4 locations on sliding surface against gear support shaft of drive releasing arm F-4-11 4.5.11 FU Delivery Roller 0002-4260 Area of application: [1]Grease:...

Chapter 4 4-13 F-4-12 4.5.12 Pickup Idler Gear 0002-4258 Are of application: [1]Grease: MOLYKOTE EM-50LAmount: 10 +/-5 mgLocation of application:- 2 locations on pickup idler gear support shaft- 5 teeth or more (covering entire large-diameter tooth surface of pickup idler gear) F-4-13 4.5.13 Feed De...

Chapter 4 　 4-14 - spread in axial direction F-4-14 4.5.14 Fixing Deceleration Gear 0002-4261 Area of application: [1]Grease: MOLYKOTE EM-50LAmount: 40 +/-10 mgLocation of application- 5 teeth or more (covering entire surface of fixing deceleration gear; small-diameter teeth) Area of application: [2...

Chapter 4 4-15 4.5.15 FD Delivery Roller 0002-4262 Area of application: [1]Grease: MOLYKOTE EM-50LAmount: 30 +/-5 mgLocation of application- entire sliding surface against FD delivery bushing F-4-16 4.5.16 Large Gear Bushing F 0002-4263 Area of application: [1]Grease: MOLYKOTE EM-50LAmount: 10 +/-5 ...

Chapter 4 　 4-16 4.5.17 Pressure roller 0002-4264 Area of application: [1]Grease: MOLYKOTE 41Amount: 10 +/-10 mgLocation of application:- edge of pressure roller shaft (sliding surface against contact spring F) F-4-18 [1]

Chapter 5 5-1 5.1 PHENOMENON TABLE 5.1.1 Symptoms 0002-9647 T-5-1 For details, see the instructions given as remedial action. Level 1 classification Description Image faults There are vertical black lines or a vertical white line in a solid black image. Malfunction The machine at times fails to go o...

Chapter 5 　 5-2 5.2 Countermeasures 5.2.1 Image Faults 5.2.1.1 Smudged/Streaked 5.2.1.1.1 There are vertical black lines or a vertical white line in a solid black image. 0003-1622 <Cause>The vertical black lines are likely to have been caused by the ribs of the heater holder. The vertical whit...

Chapter 5 5-3 5.2.3 Jam (Main Unit) 5.2.3.1 The machine identifies a jam when it is turned off and then on with paper in its manual feed section. 0003-1626 <Cause>The machine is designed to identify a jam if the manual feed paper sensor is on when it is tuned on, as it is not surewhether the p...

Chapter 5 　 5-4 5.3 MEASUREMENT AND ADJUSTMENT 5.3.1 Basic Adjustment 5.3.1.1 Items of Adjustment 0002-4265 The machine does not have items that are cited for adjustment.

Chapter 5 5-5 5.4 SERVICE TOOLS 5.4.1 Special Tools 0002-4333 T-5-2 Tool Description Parts No. Grease(MOLYKOTE EM-50L) Apply to specified areas. HY9-0007 Grease (MOLYKOTE 41) Apply to specified areas. CK-8007

Chapter 6 6-1 6.1 OUTLINE OF ELECTRICAL COMPONENTS 6.1.1 Sensor 6.1.1.1 Arrangement of Sensors and Switches 0002-4576 F-6-1 [1] Cassette Paper Sensor Used to detect the presence/absence of paper in the cassette. [2] Manual Feed Paper Sensor Used to detect the presence/absence of paper in the manual ...

Chapter 6 　 6-2 6.1.2 PCBs 6.1.2.1 Arrangement of PCBs 0002-4575 F-6-2 [1] Engine Controller Board Used to control the operation of the printer unit. [2] CAPT Board Used to serve as the interface between a PC and the printer unit. [3] Power Supply Board Used to control the supply of power to various...