Canon DC-4365 - Manuals

EN-6 WARNING: Unplug the power cord or remove the battery immediately if there is somethingwrong with your projector. Do not operate if smoke, strange noise or odor comes out of your projector, adaptor or battery. It may cause fire or electric shock. In this case, unplug immediately and contact your...

EN-8 Overview 1 2 5 6 4 8 7 3 9 Control panel 1 LAMP indicator 2 POWER indicator 3 CHARGE indicator 4 POWER button 5 F o u r d i r e c t i o n a l buttons 6 OK button 7 MENU button Terminal board 1 S-VIDEO terminal 2 VIDEO terminal 3 VGA IN terminal 4 Power jack 5 AUDIO IN terminal 6 AUDIO OUT(Earph...

EN-9 Power Using the provided AC adapter or an optional Lithium-ion rechargeable battery. Warning: The projector must be used with the provided AC adapter. Damage caused by theuse of an incorrect adapter is not covered under the warranty. Using the AC adapter 1 . Insert the plug from the AC adapter ...

EN-10 4 . Insert the plug from the AC adapter into the DC IN terminal.5 . Insert the appropriate end of the power cord into the AC adapter.6 . Insert the plug on the power cord into a wall outlet. The CHARGE indicator lights red when charging is started and turns off whencharging is completed.We rec...

EN-11 Remote control For the first time use: Remove the transparent insulation tape by pulling it beforeuse. For batter y change: 1 . Push the catch to the right and remove the battery holder. Catch Battery holder 1 POWER button 2 Four directional buttons 3 Menu button 4 Enter button 5 Keystone S T ...

EN-12 2 . Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up. 3 . Push the battery holder back into the remote control until you feel a click. Operating Range The infrared signal operates by line-of-sight up to a distance of approximately 9.8 ...

EN-14 Installation Layout of the projector Image size varies depending on the distance between the screen and the projector. Front projection L W A B H C D L : Between the screen and the front edge of the projectorA : Height of the projected image under the horizontal lineOptical offset:B:A 27:13C:D...

EN-16 VIDEO IN S-VIDEO IN to S-video output to video output VCR etc. AUDIO IN AUDIO OUT to Audio output Basic connections This projector can be connected with various devices such as a VCR, video camera,videodisc player, or personal computer that have analog RGB output connectors. Important: Make su...

EN-17 Projector + Computer For computer with D-SUB Important: When you use a longer RGB cable instead of the common length cable, the imagemay not be projected correctly.Some computers require additional connectors or analog RGB output adapters tobe connected with this projector. For Macintosh If yo...

EN-18 Preparation Preparation for projection 1 . Attach the provided AC adapter to the projector.2 . Plug the AC adapter in the wall outlet. The POWER indicator lights red when using the AC adapter. Warning: Do not look into the lens directly when the projector is on.Use 100-240 V AC 50/60 Hz to pre...

EN-19 In the following cases: Important: When the keystone adjustment is carried out, the adjustment value is indicated. Notethat this value doesn’t mean a projection angle.The allowable range of the adjustment value in the keystone adjustment variesdepending on the installation conditions.When the ...

EN-20 Basic operation On the control panel 4 3 3 Power-on 1 . Turn on the device connected to the projector first.2 . Plug the AC adapter in both the projector and the wall outlet. The POWER indicator lights up.The CHARGE indicator lights up when the projector connects with a not fullycharged batter...

EN-21 Important: Images may not be projected with good quality in an extremely hot or cold environment.(This is not a product malfunction.) 4 . Adjust the focus by turning the focus ring.5 . Choose your desired external input source using the COMPUTER / VIDEO buttons. The projector automatically sel...

EN-22 On the remote control Keystone S T button Press the Keystone S or Keystone T to adjust image distortion caused by tilting the projector. Important: Keystone adjustment will not change the shape of the menus, the start-up screen,and the background (with no signal input). Volume S T button Press...

EN-23 *1: Not active when connecting with VGA signal and SD card mode. *2: Active when connecting with VGA, Component_P and HD source. *3: Active when connecting with VGA source only. *4: Only available for SD card mode. *5: SD Slideshow Delay will be active when SD Slideshow sets to Auto. *6: Range...

EN-24 1 Color Brightness..............Use to adjust the image brightness. The image becomes brighter as the value increases. Contrast................. Use to adjust the image contrast. The contrast becomes higher as the value increases. Gamma.................. Use to select Gamma mode. PC: For compu...

EN-25 3. Management Projection Ceiling........... Use to reverse the image horizontally. Project Rear................... Use to reverse the image vertically.Source Lock................... Use to lock the current source.Lamp Hour Elapse............ Displays the LED lamp’s elapsed operating time (in h...

EN-26 Using an SD Card You can playback image and video files stored in an SD card. Video MPEG1 Supported file type: *.mpg (I-Frame Supported audio format: MPEG1 AUDIO LAYER I and MPEG1 AUDIO LAYER only) II( 8Bit OUT ) Supported audio sampling rate: 8k,11.025k,12k,16k,22k,24k,32k,48k Hz (Note: 44.1K...

EN-29 Troubleshooting The following offers solutions to some of the common problems you may encounter. Wesuggest that you consult this chart before contacting your dealer. Images aren’t projected on the screen. Problem Power isn’t turned on. Images aren’t projectedon the screen. Images suddenlydisap...

EN-30 Turn on the power of the connected device, or check whetherthere is something wrong with the connected device.Check the external device outputs signals. (Check thise s p e c i a l l y w h e n t h e e x t e r n a l d e v i c e i s a n o t e b o o kcomputer.)Check that the cable connected to the...

EN-31 Others Problem Cause and solution Projected images appear wavyand distorted. T i n t i n p r o j e c t e d i m a g e s i sincorrect. Projected images areobscured. Fine streak pattern appears inprojected images. Only the motion areas in theimages supplied from thecomputer aren’t displayed. Rain...

EN-32 This air comes out as a result of cooling the inside ofthe projector. This isn’t a product malfunction.The microcomputers inside the projector may bewrongly operating because of noise.Press the POWER button twice to turn off the lamp and unplug the power cord from the wall outlet. Waitabout 1 ...

EN-33 Maintenance Caution: Be sure to turn off the lamp and unplug the power cord from the wall outlet before youperform any maintenance on the projector. Cleaning of the projector and the ventilation slots Use a soft cloth to clean the projector and the ventilation grilles. When the grillesbecome d...

EN-34 POWER (Red) OFF ON CHARGE (Red) OFFOFF CONDITION System ON System standby POWER (Red) OFFOFF ONON CHARGE (Red) ON OFF ON OFF CONDITION System ON+Battery charging System ON + Battery full System standby+Battery charging System standby+Battery full Normal condition (AC Adaptor only) Indicators T...

EN-35 Normal condition (Battery only) Abnormal condition POWER (Red) OFF ON Flashing x 10 CHARGE (Red) OFFOFFOFF CONDITION System ON System standby Low Battery (System turned off) LAMP (Green) ON OFFOFF LAMP (Red) OFFOFFOFF Flashing x 1Flashing x 2 Flashing x3 ON POWER (Red) Off x 1 (Flashing)Off x ...

EN-36 Specifications Type DLP TM projector Rated input 15V, 2.0A Display technology Single 0.55” DLP panel Native resolution 800 x 600 pixels Colors 16.7 million Projection lens Fixed zoom with focus adjustment; F2.0 Light source RGB LED lamps Projection range Typical image size: 12" - 60"Ty...

EN-38 What’s included in the box 1 Soft Carrying Bag (for projector only)1 User’s Manual1 Quick Start Guide1 Composite Video Cable1 AC Adaptor1 Power Cord1 Remote Control1 Lithium-ion Rechargeable Battery * Output: Normal DC 11.1V 4300 mAh

EN-40 Important: Some computers aren’t compatible with the projector.The projector’s maximum resolution is 800 x 600 pixels. It may not display images ofhigher resolutions than 800 x 600 correctly.Images with SYNC on G (Green) signal may jitter.Images with SYNC on G (Green) signal may be tinged with...