Canon D1- Manuals

Page 2 - Structure of the Users Guide; Before You Begin

Structure of the Users Guide Before You Begin Operating Procedures Troubleshooting Appendix Read here first. Chapter 1 Chapter 2 Chapter 3 Chapter 4

Page 4 - Important Information

i Important Information • This manual is designed to help you to install, operate and maintain the trimmer. Please read and under- stand this manual, and keep it in a safe and convenient place. • Do not operate the trimmer until you read and understand the instructions in this manual.• Canon shall n...

Page 5 - Safe Use of Machine; Operating Safety Precautions; WARNING

ii Safe Use of Machine To use this machine safely, proper operation and periodical maintenance are indispensable. Read the safety precautions described in this manual thoroughly, and do not perform operations or maintenance procedures until you understand them completely. The operating procedures an...

Page 6 - Caution Label Locations; NOTICE

iii Caution Label Locations FCC NOTICES NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-ference when the equipment is operate...

Page 7 - CONTENTS

iv CONTENTS Important Information ...............................................................................................................iSafe Use of Machine ............................................................................................................... iiOperating Safety Pre...

Page 8 - CHAPTER

1-1 1 CHAPTER Before You Begin Machine Description ............................................................................................................................ 1-2 Section Descriptions ......................................................................................................

Page 9 - Machine Description

1-2 Machine Description Machine Description [6] [5] [3] [2] [1] [4] [1] Infeed Section (See page 1-3.)[2] Trim Section (See page 1-4.)[3] Booklet Lifter Section 1 (See page 1-5.)[4] Booklet Lifter Section 2 (See page 1-6.)[5] Front Cover[6] Conveyor Section (See page 1-7.)

Page 10 - Section Descriptions

Section Descriptions 1-3 Section Descriptions [1] Infeed Section Booklets delivered from the host machine are received here. The booklets are jogged, and then transported to the trim section. Once the trimmer is installed, you cannot touch this section. When booklet jams in this section, pull out th...

Page 16 - Operating Procedures

2-1 2 CHAPTER Operating Procedures Trimmer Setup ..................................................................................................................................... 2-2 Operation While Trimming ...........................................................................................

Page 17 - Trimmer Setup

2-2 Trimmer Setup Trimmer Setup 1 Turn on the power switch on the saddle stitcher first, then turn on the power switch on the host machine (printer). Trimmer will also be powered on because it is connected to the saddle stitcher. See the operation manual for the printer and set up the printer.

Page 18 - Operation While Trimming

Operation While Trimming 2-3 Operation While Trimming When the conveyor is full with booklets, remove the booklets. If the machine stops because the conveyor is full, remove the booklets, and the operation restarts automatically. · If you remove booklets before the conveyor is full, you can increase...

Page 20 - Troubleshooting

3-1 3 CHAPTER Troubleshooting This section describes the cause and solution of the errors. Error Messages.................................................................................................................................... 3-2 Service Call Error ..........................................

Page 21 - Error Messages; Service Call Error

3-2 Error Messages Error Messages When an error occurs and the machine does not work properly, “SERVICE CALL ERROR” appears on the LCD of the host machine (printer). If “SERVICE CALL ERROR” appears, perform as follows: Service Call Error When the SERVICE CALL ERROR appears on the LCD of the host mac...

Page 22 - Error Message Chart

Error Messages 3-3 Error Message Chart Perform the required remedies according to the error indicated on the host machine (printer). *1 If this error message appears when the conveyor is not full, trim may exists at the sensor. Cause of Error Remedy The delivery section cover is open. Close the deli...

Page 23 - Clearing Paper Jams

3-4 Clearing Paper Jams Clearing Paper Jams Procedure 1 Open the guide and check to see if there are any paper chips left on the booklet feed path. (See page 3-3.) Procedure 2 Transport belt cleaning is required. To clean the transport belt, contact your local authorized dealer. Jam in Trim Section ...

Page 24 - Appendix

4-1 4 CHAPTER Appendix Specifications ....................................................................................................................................... 4-2 Index .......................................................................................................................

Page 25 - Specifications

4-2 Specifications Specifications Specifications * 1 If the cover sheet is thinner than the other sheets in the booklet, the cover sheet may be scratched. It is recommended to use a thicker sheet for the cover sheet. * 2 The maximum number of sheets trimmable can change depending on the connected ho...

Page 26 - Index

Index 4-3 Index B Booklet Lifter Section 1 ............................ 1-2, 1-5 Booklet Lifter Section 2 ............................ 1-2, 1-6 Booklet Lifter Section Belt Unit ....................... 1-5 C Conveyor Section ..................................... 1-2, 1-7 D Delivery Section Cover .......