Canon 7822A001 - i 950 Color Inkjet Printer- Manuals

1 CLICK HERE TO GO THE INDEX Brother Cartridges Black Cartridges: IN-700, LC11BK 1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the car- tridge. (Do not remove the cap.) 2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print ...

3 CLICK HERE TO GO THE INDEX Brother Cartridges LC01BK, LC01C, LC01M, LC01Y 1. The filling hole is located under the label as shown. Just peel back the label leaving it still connected to the cartridge, do not remove completely. 2. Use the provided eyelet screw to drill a filling hole on the top of ...

4 CLICK HERE TO GO THE INDEX Brother Cartridges LC02BK, LC02C, LC02M, LC02Y, LC21Bk, LC21C, LC21M, LC21Y, LC31C, LC31M, LC31Y, LC31BK 1. Put a piece of tape over the bottom hole of the cartridge. 2. Use a flathead screwdriver to remove the cover by prying up the clip holding the cover on the cartrid...

7 CLICK HERE TO GO THE INDEX LC51 1. Cut the label at joint between the top and bottom halves of the cartridge case. 2. Flip open the cartridge casing (shell). 3. Remove the cartridge from the casing (shell). 4. There is a round hole (well) in the top of the cartridge. Inside the hole or well is a r...

8 CLICK HERE TO GO THE INDEX Brother Cartridges LC61C, LC61M, LC61Y, LC61BK, LC65BK, LC65C, LC65Y, LC65M LC71C, LC71M, LC71Y, LC71BK LC75C, LC75M, LC75Y, LC75BK, LC79BK, LC79C, LC79Y, LC79M LC103BK, LC103C, LC103M, lC103Y, LC105BK, LC105C, LC105M, LC105Y 1. Place the cartridge over a towel, or paper...

9 CLICK HERE TO GO THE INDEX Canon Cartridges BCI-21 Black & 24 Black BCI-21 Color & 24 Color 1. Use a knife to remove the top of cartridge(s). 2. Use the included eyelet screw to enlarge the filling hole(s) in the top of the cartridge(s). 3. Connect the needle to the syringe and fill with i...

10 CLICK HERE TO GO THE INDEX Canon Cartridges BC-20 & BC-23 High Capacity Cartridge 1. Use the eyelet screw to remove plug located on top of the cartridge. 2. Connect the needle to the syringe and fill with ink. 3. Insert the syringe through the filling hole and push into the cartridge. Note: Y...

12 CLICK HERE TO GO THE INDEX Canon Cartridges BC-01, BC-02, BC-05, BX-02, BX-03, 1. Use the eyelet screw to remove plug located on the top side of the cartridge. FOR BX-03 ONLY : A hole must be made on the top of the cartridge by us- ing the hole making tool included in the kit. . Firmly hold the h...

14 CLICK HERE TO GO THE INDEX Canon Cartridges BCI-3e , BCI-3, BCI-5, BCI-6, Cli-8, PGI-5, PGI-220, CLI-221, PGI-225, CLI-226, PGI-250, CLI-251 (All Colors) NOTE: Canon Resetter may be required to have the cartridges resgister as full upon installation. Method #1 Using a manual drill or the small dr...

15 CLICK HERE TO GO THE INDEX Canon Cartridges Method #2 1. Use electrical or duct tape to seal the Air Vent found on the top of the cartridge. Note: Make sure tape is completely covering the vent. 2. Remove the label partially, only to expose the ball bearing underneath. Then use a screw- driver or...

16 CLICK HERE TO GO THE INDEX BCI-15B / BCI-16C 1. Put the cartridges on some paper towels in an area where you can toler- ate a spill. 2. Turn the cartridge up side down so that the outlet port of the cartridge is facing upward. 3. Fill the syringe with 3ml of ink for the color being refilled. 4. D...

17 CLICK HERE TO GO THE INDEX Canon Cartridges BC-22e 1. Use the eyelet screw to remove the plugs located on top of the cartridge. 2. Connect the needle to the syringe and fill with ink. 3. Insert the syringe through the filling hole and push into the cartridge. Note: You may feel a slight pressure ...

18 CLICK HERE TO GO THE INDEX 1. Remove the label from the top of cartridge 2. Using the drill tool, widen the refill holes for each color. Please use the illustrations on the right for color guidance. 3. Attach the needle to syringe and load syringe with 6 ml of ink for each color in the color car-...

19 CLICK HERE TO GO THE INDEX Compaq Cartridges Black Cartridges: 337714-001, 180845-001, 337709-001, 180847-001 1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge. (Do not remove the cap.) 2. Connect the needle to the syringe and fill the syringe with 8...

20 CLICK HERE TO GO THE INDEX Dell Cartridges Black Cartridges: Dell: 7Y743, T0529, T0601 Lexmark: 18L0032 1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge. (Do not remove the cap.) 2. Connect the needle to the syringe and fill the syringe with 8 ml. o...

21 CLICK HERE TO GO THE INDEX Dell Cartridges MAGENTA CYAN YELLOW BLACK Dell 21, 22, 23, 24 Series 1. Peel back the label from the top of the cartridge to expose the refill holes of the car- tridge. (If the illustration on the right differ from your cartridge model, use 3 tooth- picks and poke each ...

22 CLICK HERE TO GO THE INDEX Digital Cartridges LJ50X-AB, LJ50X-AK, LJ50X-AC Color Cartridge 1. The filling holes are located under the cap. The cap is easily removed by simply pulling it off with your fingers. Be careful not to damage the sensors on the back 2. Connect the needle to the syringe an...

23 CLICK HERE TO GO THE INDEX Epson Cartridges S020062, S020118, S020122, S020130 1. The filling hole is the same hole as the hole that connects to the printer. 2. Note: The cartridge is lined in a delicate Mylar bag and it is very important not to insert the needle more than 3/4” or it is possible ...

24 CLICK HERE TO GO THE INDEX Epson Cartridges S020093, S020097, S020110, S020193, S020187, S020189, S020191, S020089, S020093, S020108, S020047, S020049, S020097, S020034, S020036, S020138, T001, T003011, T003012, T005011, A Chip Resetter (sold separately) is needed for the following: T007201, T008...

26 CLICK HERE TO GO THE INDEX Epson Cartridges A Chip Resetter (sold separately) is needed for the following cartridges: T0431, T0441, T0442, T0443, T0444, T0481, T0482, T0483, T0484, T0485, T0486, T0540, T0541, T0542, T0543, T0544, T0545, T0546, T0547, T0548, T0549, T0601-T0604 1. It is important t...

27 CLICK HERE TO GO THE INDEX Epson Cartridges A Chip Resetter (sold separately) is needed for the following cartridges: T124120, T124220, T124320, T124420, T125120, T125220, T125320, T125420, T126120, T126220, T126320, T126420, T127120, T127220, T127320, T127420, T128120, T128220, T128320, T128420 ...

28 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges 51626A, 51629A, 51626G, 51629G, 51633M, C6614AN, C6628AN 1. Put a piece of tape over (Aerator “B”) on the bottom of the cartridge. This aerator must be sealed tightly to prevent leaking. - See diagram. 2. Aerator “C” is located in the center o...

29 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges 51625A, 51649A , 51649G, C1816A 1. The plastic cover must be remove to reveal the filling holes. Carefully pry it off with a thin metal blade, such as a thin flathead screwdriver. Or lay the car- tridge on its side with the plastic cap off the...

30 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges 51645A, 51645G, 51640A, 51640C, 51640M, 51640Y, 51644C, 51644M, 51644Y, C6615DN , C6615AN 1. Turn the cartridge upside down and using a peel back the plastic film covering the stainless steel ball bearing as shown below. 2. Using a screwdriver...

31 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges 51641A, C1823A, C1823D, C1823G, C6625AN, C6578AN, C6578DN, C3844A, C3845A 1. The small sealed holes on the top are the filling holes. Use a small screwdriver to push the plastic seals into the cartridge. 2. Connect the needle to the syringe an...

32 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges C4841A, C4842A, C4843A, C4844A 38, 50, 70, 72, 80, 81, 82, 83, 88, 90, 940 1. Cut label at joint between top and bottom cap of cartridge case. 2. Flip back the bottom cap of cartridge. 3. Squeeze the sides of cartridge casing and wiggle out th...

33 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges 21, 22, 27, 28, 56, 57, 58, 60, 61, 61XL, 74, 74XL, 75, 75XL, 92, 93, 94, 95, 96, 97, 98, 99, 901 1. Peel back the label from the top of the cartridge to expose the refill holes of the cartridge. (If the illustration on the right differ from y...

34 CLICK HERE TO GO THE INDEX HP Cartridges HP 701 1. Peel back the label from the top of the cartridge to expose the vent hole of the cartridge. 2. Fill the syringe with 15 ml of black ink (5 ml for each color on color car- tridges) . 3. If the vent hole is to small, use the provided drill to incre...

35 CLICK HERE TO GO THE INDEX HP Cartridges HP 564 and 920 1. Use electrical or duct tape to seal the Air Vent found on the top of the cartridge. Note: Make sure tape is completely covering the vent. 2. Remove the label partially, only to expose the ball bearing underneath. Then use a screw- driver ...

36 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges C1806A, C1807A, C1808A, C1809A 1. Remove the Mylar ink bag from the cardboard covering. Note: (This Mylar ink bag is very delicate and must be handled with care). 2. Use both hands when holding the top of the Mylar bag and use both thumbs to p...

37 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges C5010A, C5011A 1. Connect the needle to the syringe. Using the needle, pierce through the label into the cartridge. Note: We have removed the label to illustrate where the filling holes are located. We do not recommend removing it. 2. After yo...

38 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges C6634A, C6635A 1. Drill filling holes on the top of the cartridge (as shown below left) or pry off the cartridge top as shown below right. Do the procedure that is easier for you. Use the hole making tool included in the kit, drill each fillin...

39 CLICK HERE TO GO THE INDEX Refilling the Black Cartridge: 1. Use the enclosed eyelet screw to create the filling hole at the top of the cartridge. Picture A, on the right, illustrates where the refill hole should be created. 2. Fill the syringe with ink. Insert the needle into the filling hole an...

40 CLICK HERE TO GO THE INDEX Hewlett Packard Cartridges 932, 933, 950, 951 1. Locate the “Fill Port” on your cartridge. 2. You should see a plastic ball in this “Fill Port”. Use a allen wrench, or a small screw driver with a hammer, to gently knock the plastic ball into the cartridge. 3. Connect th...

41 CLICK HERE TO GO THE INDEX Chip Replacement This illustration shows the cartridge sitting in its upright position. The chip is located on the bot- tom part of the cartridge. Although this cartridge may sit in a certain position in your printer, this would be considered the correct upright positio...

42 CLICK HERE TO GO THE INDEX Kodak Cartridges Black Black Cyan Magenta Glossy Yellow *Chip installation instructions* Newly refilled Kodak ink cartridges need to have their chips replaced with new chips so that the printer can “recognize” them as full again. Aftermarket chips are slightly different...

43 CLICK HERE TO GO THE INDEX Lexmark Cartridges Black Cartridges: 10N0016, 10N0217, 12A1970, 12A1975, 1361400, 13400HC, 1380620, 1382050, 15M2971, 16G0055, 17G0050, 18L0032, 1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge. (Do not remove the cap.) 2....

44 CLICK HERE TO GO THE INDEX Lexmark Cartridges 1380490, 1380491, 1380492, 1380493 1. The filling hole is the same hole as the hole that connects to the printer. 2. Note: The cartridge is lined in a delicate Mylar bag and it is very important not to insert the needle more than 3/4” or it is possibl...

46 CLICK HERE TO GO THE INDEX Lexmark Cartridges / Dell Cartridges 1. Peel back the label from the top of the cartridge to expose the refill holes of the cartridge. (If the illustration on the right differ from your cartridge model, use 3 toothpicks and poke each hole to de- termine its color) 2. Fi...

47 CLICK HERE TO GO THE INDEX Lexmark Cartridges / Dell Cartridges Items needed : gloves, hand-drill, cartridges, paper towels. Note : You will need the Lexmark 100A version. Some models may require a new replacment chip to succesfully reset the cartridge. Lexmark offers for sale two different versi...

48 CLICK HERE TO GO THE INDEX Okidata Cartridges Black Cartridge: 52109301 1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the car- tridge. (Do not remove the cap.) 2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print Head C...

49 CLICK HERE TO GO THE INDEX Okidata Cartridges 52110001, 52110002, 52110003, 52110004 1. The filling hole is located under the label as shown. Just peel back the label leaving it still connected to the cartridge, do not remove completely. 2. Use the provided eyelet screw to drill a filling hole on...

50 CLICK HERE TO GO THE INDEX Pitney Bowes Cartridge 769-0 1. Put a piece of tape over the exit hole located on the bottom of the cartridge 2. The filling hole is located on the back of the cartridge and must be widen using the included eyelet screw 3. Connect the needle to the syringe and fill with...

52 CLICK HERE TO GO THE INDEX Xerox Cartridges Color Cartridges: 8R12591, 8R7880, 8R882 1. The filling holes are located under the plastic cap. Use a thin flathead screw\driver or knife to remove the cap. Important: Do not to damage the sensors on the back of the cartridge. 2. Connect the needle to ...

54 CLICK HERE TO GO THE INDEX Xerox Cartridges 8R7638 1. Using the included hole making tool make a filling hole in the front of the cartridge about 1/2” from the top. 2. Connect the needle to the syringe and fill with ink. 3. Insert the filling needle into the hole and aim it towards the center of ...

55 CLICK HERE TO GO THE INDEX Xerox Cartridges 8R7903, 8R7904 1. The filling holes are located under the plastic cap. The cap is held in place with a pin at the each corner. Use a thin flathead screwdriver or knife to remove the cap. Important: Do not to damage the sensors on the back of the cartrid...

56 CLICK HERE TO GO THE INDEX Xerox Cartridges 8R12728 1. Use the eyelet screw to make the filling hole in the small notch on the corner located next to the “1” shown on the label. 2. Fill the syringe with ink and inject about 8 ml. of ink until the ink tank is full. 3. Use a piece of tape to seal t...

57 CLICK HERE TO GO THE INDEX Xerox Cartridges 8R7971, 8R7972, 8R7973, 8R7974 1. The filling hole is located under the label on the top of the cartridge. Use the empty needle to pierce through the label to make the filling hole. 2. Fill the syringe with ink and inject about 4 ml. of ink until the in...

58 CLICK HERE TO GO THE INDEX Pitney Bowes 793-5 1. Peel off the sticker on the top front of the cartridge (original Pitney Bowes cartridges have a sticker that covers the entire top side of the cartridge, whereas NuPost Compatible cartridges have a smaller sticker). 2. Underneath the sticker, you w...

59 CLICK HERE TO GO THE INDEX 797-0 1. SKIP THIS STEP if your cartridge is not a Pitney Bowes original cartridge. The original PB cartridges have a cap which needs to be removed. Using a medium sized flat screwdriver, lift the tab as shown in the picture. Once the tab has cleared the top of the cart...