Page 3 - Preface; Important Information; SAFETY PRECAUTIONS; CAUTION – TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE; adjacent to the power inlet housing the fuse.; PRECAUTIONS DE SECURITÉ; élément ne peut être réparé par un particulier.; SICHERHEITSVORKEHRUNG
Preface P117F(R) Stackable Switch Installation Guide 1 Important Information SAFETY PRECAUTIONS CAUTION – TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE 1. All servicing should be undertaken ONLY by qualified personnel. The parts inside the unit CANNOT be serviced or repaired by the end user. Please ...
Page 5 - Chapter 1; Overview; This guide is divided into four main sections:; Description
Chapter 1 Overview This guide is divided into four main sections: • Overview: A general description of the features of the Avaya Stackable Switch and P117FR (jointly referred to as the P117F(R)). • Installation: Instructions for getting the P117F(R) Stackable Switch and P110 stack up and running. • ...
Page 7 - Chapter 2; Installation; Setting the DIP switches; Figure 1
Chapter 2 Installation Setting the DIP switches First, set the DIP switches. The position of the switches depends on the application. The drawing below shows the default positions of the DIP switches on the rear panel of the P110 switch. Figure 1 The P117F(R) Stackable Switch Rear Panel Showing the ...
Page 8 - Installing the P117F(R) Stackable Switch; Standalone Operation - Plug ‘n’ Play; The switch is now fully operational.; Stacking Operation; NMA does not contain the latest software version, you have to
Chapter 2 Installation Installing the P117F(R) Stackable Switch The procedure for getting the P117F(R) Stackable Switch up and running depends on whether the switch is to operate in standalone or as part of a stack. Standalone Operation - Plug ‘n’ Play Getting the P110 switch working is quick and ea...
Page 9 - or other P110 switches in the stack. The P110 NMA must be; Cabling Requirements:; be installed
Chapter 2 Installation 4. Place the P117F(R) or other P110 switches in the stack. The P110 NMA must be in the top switch of the stack. To ensure proper ventilation, ensure that all empty P110 NMA slots in the stack are closed. 5. Connect P110 switches using the supplied P110 Exoplane cables, as show...
Page 10 - and
Chapter 2 Installation The P110 NMA and the on-board agent in all P110 switches (e.g., P117F(R) and P113F) must have the same version number. 8 P117F(R) Stackable Switch Installation Guide
Page 11 - Rack Mounting; Figure
Chapter 2 Installation Rack Mounting P110 switches slot into a standard 19-inch rack. If the switches are to be rack mounted, first place them in the rack, then connect the P110 Exoplane, as follows: 1. Snap open the ends of the front panel to reveal the fixing holes. 2. Slot the switch into the rac...
Page 12 - Diagnostics; Figure 4
Chapter 2 Installation Diagnostics Tables 2 and 3 explain the meaning of the P117F diagnostic LED indicators. Figure 4 The P117F Front Panel LEDs and Buttons Figure 5 The P117FR Front Panel LEDs and Buttons 10 P117F(R) Stackable Switch Installation Guide
Page 13 - Table 2
Chapter 2 Installation Table 2 Meaning of the P117F Front Panel Buttons Button Function Meaning Select The buttons determine what function will be displayed by the 17 Port LEDs (the top two rows of LEDs). The five Function LEDs (above the Select buttons) show which function is currently displayed by...
Page 14 - Table 4
Chapter 2 Installation LED Indicator Function Status Meaning duplex ON (Ethernet only) Full duplex connection to port (ATM is always ON) Table 4 Meaning of the additional P117FR front panel LEDs LED Indicator Function Status Meaning M S Master port (Upper ATM connector) Secondary port (Lower ATM con...
Page 15 - Chapter 3; Software Download to the On-Board Agent; not; Connecting the Console Terminal; Console
Chapter 3 Software Download to the On-Board Agent The P117F(R) contains an on-board agent. This agent does not use the same software as the P110 NMA. When you receive the P117F(R), its on-board agent comes pre-loaded with fully functional software. New software is made available at regular intervals...
Page 16 - Software Download Summary; If you’re using routers, set up a default gateway.; Setup Menus; Setup Main Menu; Underlined spaces in the example screens represent variables.
Chapter 3 Configuration Software Download Summary Below is a procedure checklist for successfully configuring a P117F(R) for SNMP management. Instructions for each item in the list can be found in the pertinent sections of this guide. If necessary, enter an IP address for the P117F(R), and reset the...
Page 17 - Press; Enter; to view the Setup Main Menu.
Chapter 3 Configuration Press Enter to view the Setup Main Menu. Notes: • The following Setup Main Menu is correct for a stand-alone P117F(R) module without an NMA agent card inserted. • An NMA module is required in a stack configuration. In this case options 5 and 6 are set via the P110 NMA setup m...
Page 18 - How to Navigate through the Setup menus; Save the
Chapter 3 Configuration How to Navigate through the Setup menus • All Setup menus conform to the following display conventions: This symbol Means ... This item has a sub-menu [ ] This item has a sub-menu to insert parameter values 1, 2, 3, etc. Denotes a sequence number. To select an item from any m...
Page 19 - Parameter configuration; Display Current Version; — Reset the Module
Chapter 3 Configuration Parameter configuration The following sections provide step-by-step instructions for configuring each parameter. In many module configuration menus, the following parameters are displayed: • Display Current Version shows the active configuration. • Display Configured Version ...
Page 20 - — Software Download; In the P110 on-board agent, the flash memory contains; two; independent software
Chapter 3 Configuration 2 — Software Download General When you receive the P117F(R), its on-board agent comes pre-loaded with fully functional software. New software is made available at regular intervals. You should make sure that all P110 units contain the latest available software. The P110 on-bo...
Page 21 - The TFTP Process; TFTP Server and File parameters
Chapter 3 Configuration The TFTP Process The agent software file should be placed on a computer that can be located anywhere on the network. During the TFTP process, the computer acts as the Server and the agent as the Client. From the Terminal, the user configures the agent with the IP address of t...
Page 22 - Start Software Download process; . You will get a warning and a; Monitor; . Press Enter to get an update of the download
Chapter 3 Configuration TFTP Server IP address: 000.000.000.000 File Name: __________ Destination: Flash B (Application) >>>Enter Server IP address [000.000.000.000]: 135.49.60.115 >>>Enter File Name: /home/v16155 >>>Enter Destination (1-Flash A (Basic), 2-Flash B (Applica...
Page 23 - Troubleshooting Software Download
Chapter 3 Configuration Agent Software Download Monitoring Screen Visage 16155(R) S/W Version: ____ Slot #: ____ TFTP Server: 135.49.60.115 File Name: c:/home/v16155 Destination: Flash Bank B (Application) Download State : tftp-running-ip Activity Status : Download Process Started Download Size : --...
Page 24 - — Agent Access Addresses; The agent also stores a; from the Setup Main Menu. This opens the; InBand Interface
Chapter 3 Configuration 3 — Agent Access Addresses This parameter stores IP addresses for the P117 agent’s communication interfaces in stand-alone mode. The interface addresses facilitate communication between the agent and the management station. By assigning an IP address to the agent interface, y...
Page 26 - — IP Routes; The IP address of the station or the network (not subnet)
Chapter 3 Configuration 4 — IP Routes When the P117F(R) is in stand-alone configuration and is connected to one side of a router (on one network) and the file containing the new software is located on the other side of the router (on a different network), you must set up a communication path via the...
Page 27 - IP Routes; from the Setup Main Menu. This opens the IP Routes sub-; Add; to define a new IP Route.; Delete; to remove an existing IP Route.
Chapter 3 Configuration To define an IP Route: 1. Select IP Routes from the Setup Main Menu. This opens the IP Routes sub- menu shown below. IP Routes menu Visage 16155(R) S/W Version: ____ Slot #: ____ <CR> Refresh the screen 0 Return to previous menu 1 Save the Session 2 List - static routin...
Page 28 - List; To save your changes select; Save the Session; to return to the Setup main menu.
Chapter 3 Configuration 3. Type the destination address of a host (IP address of the management station) or a network (IP of management network) as shown in the menu below and press Enter . For a default gateway, leave the destination address as 000.000.000.000 . IP Route parameters menu Visage 1615...
Page 29 - – SNMP Community; The default community for all three options is
Chapter 3 Configuration 5 – SNMP Community (Not applicable for P117F(R) Stackable Switch in a stack) This parameter defines the trap, read-only and read-write communities. The community name can be up to 24 characters in length. The default community for all three options is public . SNMP Community ...
Page 30 - Select Update to change the community:; without; saving the changes.
Chapter 3 Configuration 1. Select Update to change the community: Trap Community Menu Visage 16155(R) S/W Version: ____ Slot #: ____ <CR> Refresh the screen 0. Return to Previous Menu 1. Save the Session --------------------------------- 2. Update [] >>>Enter your choice: 2 Trap Commu...
Page 31 - – Permanent Managers; Listing Permanent Managers; Press Enter to return to the Permanent Managers Menu.
Chapter 3 Configuration 6 – Permanent Managers (Not applicable for P117F(R) Stackable Switch in a stack) This option allows you to define up to ten management stations which can receive alarms. Permanent Managers Menu Visage 16155(R) S/W Version: ____ Slot #: ____ <CR> Refresh the screen 0. Re...
Page 32 - Adding Permanent Managers
Chapter 3 Configuration Adding Permanent Managers 1. To add permanent managers, select Add: 2. Type in the IP address of the permanent manager and press Enter. Deleting Permanent Managers 1. Select Delete from the Permanent Managers Menu: 2. Select the index number (1 - 10) of the permanent manager ...
Page 33 - – Module Advanced Configuration; This option is not currently implemented.; Changing the UNI Version; Select “Change configured UNI version”:
Chapter 3 Configuration 7 – Module Advanced Configuration (Not applicable for P117F(R) Stackable Switch in a stack) This option is not currently implemented. 8 (5) – UNI Version This option determines the UNI version used for the P117F(R). Before changing the UNI Version check that the ATM switch su...
Page 34 - Changing the ATM Physical Media; You will need to reset the unit in order to implement the change.
Chapter 3 Configuration 9 (6) – ATM Physical Media This option allows you to change the ATM media to be SONET or SDH. To access the ATM physical media menu select ATM Physical Media. Before choosing the ATM Physical Media, check that the ATM switch supports this media type. ATM physical media menu V...
Page 35 - unit. To access the ATM address prefix menu select ATM Address:; either
Chapter 3 Configuration 10 (7) – ILMI/ATM Address This option allows you to define how the ATM address prefix will be allocated to the P117F(R) unit. To access the ATM address prefix menu select ATM Address: ILMI/ATM address menu Visage 16155(R) S/W Version: ____ Slot #: ____ <CR> Refresh the ...
Page 36 - Changing the Configured LECS ATM address
Chapter 3 Configuration 11 (8) – LECS ATM Address This option allows you to change the LECS ATM address. This address is derived using the following algorithm: 1. Address entered by the user 2. ILMI (if the user has not entered a value) 3. Well-known address (WKA) 4. VP0 VC17 It is therefore not nec...
Page 38 - Display ELAN/VLAN associations
Chapter 3 Configuration Display ELAN/VLAN associations 1. To view current ELAN/VLAN assocations select Display ELAN/VLAN associations. An example is shown here: ELAN/VLAN Associations: Assoc LecIF Index Vlan Elan Status Status IfIndex -----------------------------------------------------------------...
Page 39 - Displaying Default ELAN information; column of the ELAN/VLAN associations list.; Changing the Default ELAN Name; To change the default ELAN name select Change default ELAN name:; alpha
Chapter 3 Configuration Displaying Default ELAN information The default ELAN is the ELAN associated with VLAN 0. 1. To display the default ELAN information, select Display default ELAN information: Default ELAN information (VLAN = 0): Association: 1 Elan name: default Assoc Status: Active LecIf Stat...
Page 40 - To display Current Redundancy Parameters, select
Chapter 3 Configuration 13 (10) – ATM Redundancy This menu only appears for the P117FR, which has a redundant ATM port. This menu enables and disables the redundancy mechanism. Redundancy can be Enabled or Disabled, and the Active port can be either the Upper or the Lower port. ATM Redundancy menu S...
Page 41 - 4 (11) – Set ATM Port Parameters to their Default Values; from the device manager.
Chapter 3 Configuration 14 (11) – Set ATM Port Parameters to their Default Values This option returns the ATM port parameters to their default values. ATM port default values: UNI Version : 3.1 Physical Media : SONET ATM Address : Using ILMI LECS ATM Address : Using ILMI/WKA/PVC ELAN Configuration :...
Page 43 - Chapter 4; Terminal Connector Pin Assignments
Chapter 4 Terminal Connector Pin Assignments Figure 6 Terminal port – RS-232 Wiring Connection to Console Terminal P117F(R) Stackable Switch Installation Guide 41
Avaya 16-601433
Manual
Avaya 4600
Manual
Avaya 1603
Manual
Avaya 555-245-703
Manual
Avaya Gigabit Ethernet Adapter
Manual
Avaya 4606
Manual
Avaya 585-215-871
Manual
Avaya 4412D+
Manual
Avaya S8400
Manual
Avaya 10-Watt
Manual
Avaya 9600
Manual
Avaya R3.0
Manual
Avaya 1120E
Manual
Avaya 555-245-600
Manual
Avaya 16xx
Manual
Avaya Desk
Manual
Avaya B149
Manual
Avaya 2402
Manual
Avaya IPM515
Manual