Page 2 - Figure 1
DJB; Reviewed: PV 4/13/06 Solution & Interoperability Test Lab Application Notes ©2006 Avaya Inc. All Rights Reserved. 2 of 18 3448PAppNotes.doc 1. Introduction Power over Ethernet (PoE) allows both power and data to be simultaneously carried over standard Ethernet cables. PoE-enabled Ethernet s...
Page 3 - Successful boot operation.; Figure 1: PoE Interoperability Between Dell PowerConnect
The power tests included verification of the following after the product was connected to the switch: • Successful boot operation. • For Avaya IP Telephones, successful registration with Avaya Communication Manager or Avaya IP Office (the Avaya 5600-Series IP Telephones are only supported on IP Offi...
Page 4 - Equipment and Software Validated; Equipment; Configure Dell PowerConnect 3448P
DJB; Reviewed: PV 4/13/06 Solution & Interoperability Test Lab Application Notes ©2006 Avaya Inc. All Rights Reserved. 4 of 18 3448PAppNotes.doc 2. Equipment and Software Validated The following equipment and software/firmware were used for the sample configuration provided: Equipment Software/F...
Page 5 - Getting Started with a New or Initialized System; Enter
DJB; Reviewed: PV 4/13/06 Solution & Interoperability Test Lab Application Notes ©2006 Avaya Inc. All Rights Reserved. 5 of 18 3448PAppNotes.doc 3.1. Getting Started with a New or Initialized System 1. Identify the IP Address, Subnet Mask and Default Gateway that will be used for the Dell PowerC...
Page 6 - admin
DJB; Reviewed: PV 4/13/06 Solution & Interoperability Test Lab Application Notes ©2006 Avaya Inc. All Rights Reserved. 6 of 18 3448PAppNotes.doc Now we need to setup your initial privilege (Level 15) user account. This account is used to login to the CLI and Web interface. You may setup other ac...
Page 8 - Add; . This opens up a new browser. Enter the VLAN ID for the Voice VLAN and a; Apply Changes; . Go back to the main VLAN screen and press; Refresh
10. Create a VLAN for the Voice VLAN . Select Switch->VLAN->VLAN Membership . Press Add . This opens up a new browser. Enter the VLAN ID for the Voice VLAN and a Name. Press Apply Changes . Go back to the main VLAN screen and press Refresh . The newly created VLAN is now displayed. DJB; Review...
Page 10 - Apply
12. Tag the appropriate ports on the VLAN. Select Switch->VLAN->VLAN Membership. All IP telephone ports must be tagged. The Telephony server (IP Office or Avaya Communication Manager and the PC running IP Office Manager must be Untagged (in this example, the telephone ports are 5 – 10 and the ...
Page 11 - Configure QoS for the IP Phone ports. Select; Enable; for Quality of Service and; CoS; for Trust
13. Configure QoS for the IP Phone ports. Select Quality of Service->Global Parameters->Global Settings . Select Enable for Quality of Service and CoS for Trust Mode. DJB; Reviewed: PV 4/13/06 Solution & Interoperability Test Lab Application Notes ©2006 Avaya Inc. All Rights Reserved. 11 o...
Page 14 - successfully provided inline power to the Avaya IP telephones.
DJB; Reviewed: PV 4/13/06 Solution & Interoperability Test Lab Application Notes ©2006 Avaya Inc. All Rights Reserved. 14 of 18 3448PAppNotes.doc 4.2. Test Results All Power over Ethernet test cases completed successfully. The Dell PowerConnect ™ 3448P successfully provided inline power to the A...
Page 15 - Verification and Troubleshooting; Unplug the set and plug it back in. When prompted, press; Home; on the browser interface (see below) and verify that the
5. Verification and Troubleshooting If an IP telephone does register, check the following: • Unplug the set and plug it back in. When prompted, press * . Verify that all IP Addresses and VLANs are correct. Plug the IP telephone directly into the Dell PowerConnect ™ 3448P if possible. Select Home on ...
Page 17 - Additional References
• Check that the ports are correctly marked as tagged or untagged. Select Switch->VLAN->VLAN Membership. Verify the IP Telephone ports show T and the Telephony Server port (IP Office or Avaya Communication Manager) shows U. 6. Conclusion These Application Notes describe the steps for configuri...