BEA LO-21P - Manual
BEA LO-21P – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – STANDARD WIRING; WIRE CONNECTIONS; red; BODYGUARD; EAGLE; Approach SuperScan; yellow; SAFETY; AUTO; OPERATOR; Door Control
- Page 3 – MOTOR; Bodyguard must be programmed to a relay value of 2.
- Page 5 – CLOSED DOOR; Volts DC; STOP
- Page 6 – sec
- Page 8 – RANS; beas; PARALLAX II SYSTEM Q-DISCONNECT; WHITE; IK; BLACK; 7 STALL INPUT; LEFT APPROACH SIDE; BROW
- Page 9 – RANSF; BLUE; ee Not; YELLOW
- Page 10 – TRANSFORMER; VIOLET; COMMON; ST; WHI; GRAY
- Page 11 – WHIT; TI
- Page 12 – rs; IL; IS; IG
- Page 13 – ROL; GREEN
75.5079.08 20061129
Page 1 of 13
PRODUCT
DESCRIPTION
TECHNICAL
SPECIFICATIONS
USERS GUIDE
LO-21P
LOCK OUT RELAY
COMPONENT ID
SAFETY
PRECAUTIONS
The microprocessed LO-21P (PN: 10LO21P) Lock Out Relay is designed to provide a lockout function for the BEA
Bodyguard presence sensor, when used with the complete Parallax System. The LO-21P uses the motor and Bodyguard to
determine if the swing path of the automatic door is clear and allows the door to open or close. If the swing path of the
automatic door is not clear and the door is in the open position, the LO-21P will allow the Bodyguard to hold the door open
as long as it detects something. If the door is closed and there is something in the Bodyguard pattern, the LO-21P will
prohibit the activation device from opening the door.
•
Shut off all power going to the header before attempting any wiring procedures.
•
Maintain a clean & safe environment when working in public areas.
•
Constantly be aware of pedestrian traffic around the door area.
•
Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected
reactions by the door.
•
Always check placement of all wiring before powering up to insure that moving door parts will not catch any
wires and cause damage to equipment.
•
Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
DESCRIPTION
SPECIFICATIONS
Power Supply
12-24 Volts AC/ DC
Operating Frequency
4 MHz (Microprocessor)
Power Consumption
10 mA at rest, 50 mA Max.
Output SPST
Relay
Max. Voltage - Relay Contact
60V DC, 120V AC
Max. Current - Relay Contacts
2A DC, 0.5A AC
Dipswitches
Green LED – Activation
Red LED – Safety
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
75.5079.08 20061129 Page 2 of 13 ELECTRICAL INSTALLATION – OPTION 1 – STANDARD WIRING STANDARD WIRING WIRE CONNECTIONS Black Motor Input - Red Motor Input + Purple Bodyguard COM. Pin 3 White Bodyguard Data (-) Pin 6 Black / White Activation Sensor COM. Orange Power input / 12-24 VAC/VDC ( - ) Gray B...
75.5079.08 20061129 Page 3 of 13 ELECTRICAL INSTALLATION OPTION 2 – Operator Mounted Switch Wiring diagram below shows how to wire when using an operator-mounted switch to control the flow of voltage from the motor to the lockout module. Switch should be set to close a set of dry contacts when door ...
75.5079.08 20061129 Page 5 of 13 SET-UP INSTRUCTIONS Upon completion of all wiring, proceed with the set-up as follows: 1. Insure that the On-Off-Hold Open switch is in the ON position, and insure that the door control is powered and operating normally. 2. Power the Bodyguard sensor and, using a BEA...
