Page 3 - Contents
Issue 8 February 2007 3 Chapter 1: Before You Go to the Installation Site . . . . . . . . . . . . . 5 Other documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 License file, software, and firmware . . . . . . . . . . . . . . . . . . . . . . . . . 5 Laptop requirements ....
Page 5 - Chapter 1: Before You Go to the Installation Site; Other documents; Obtain access to the following documentation:
Issue 8 February 2007 5 Chapter 1: Before You Go to the Installation Site The following activities must be completed before going to an installation site. Other documents Obtain access to the following documentation: ● The G700/S8300 Installation guide: Installation and Upgrades for Avaya G700 Media...
Page 6 - Communication Manager; Laptop requirements
Before You Go to the Installation Site 6 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server 3. Retrieve the required license file from Remote Feature Activation (RFA). Note: Note: As of Communication Manager Release 3.1, the Avaya Installation Wizard no longer require...
Page 7 - Chapter 2: Conduct Equipment Inventory; Avaya G700 Media Gateway Chassis
Issue 8 February 2007 7 Chapter 2: Conduct Equipment Inventory The following list of equipment contains items that may not be needed for your configuration — those items are specified as "optional" and may not be included in your inventory. Avaya G700 Media Gateway Chassis Optional Avaya S83...
Page 8 - Optional Avaya MM760 VoIP Media Module
Conduct Equipment Inventory 8 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server Optional Avaya MM716 24-port Analog Media Module Optional Avaya MM717 24-port DCP Media Module. Note: Note: Endpoints connected to this media module must be in-building only. Optional Ava...
Page 10 - Screw Packet and Rack Mount Brackets
Conduct Equipment Inventory 10 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server Screw Packet and Rack Mount Brackets For each bracket: ● three flat-head machine screws attach the bracket to the G700 ● two round-head lock-washer machine screws attach the bracket to t...
Page 12 - Optional AC Power Cord
Conduct Equipment Inventory 12 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server Optional AC Power Cord Optional DC Power Cord. Feet used for table mounting.
Page 13 - Chapter 3: Mount Media Gateway; Wear an anti-static ground wrist strap
Issue 8 February 2007 13 Chapter 3: Mount Media Gateway 1. Wear an anti-static ground wrist strap and attach to an approved ground. 2. For rack mount, install the mounting brackets on the left and right sides of the gateway chassis using the flathead screws from the bracket packet. Note: Note: The b...
Page 14 - For desktop mount. Install feet using
Mount Media Gateway 14 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server 4. For desktop mount. Install feet using plastic push rivets. 5. Connect the ground wire to the ground conductor on the back of the media gateway. 6. Attach the other end of the ground wire to a...
Page 15 - Chapter 4: Install Octaplane Stacking Module; Remove the blank faceplate from
Issue 8 February 2007 15 Chapter 4: Install Octaplane Stacking Module Note: Note: Complete these steps only if you are connecting more than one G700 Media Gateway in a stack configuration. 1. Remove the blank faceplate from the Octaplane slot on the back of the media gateway. 2. Align the X330STK Oc...
Page 17 - Chapter 5: Connect Media Gateways
Issue 8 February 2007 17 Chapter 5: Connect Media Gateways Note: Note: Complete these steps only if you are connecting more than one G700 Media Gateway in a stack configuration. 1. Using the gray X330SC short cables, connect the media gateways from the bottom up: ● Connect the light gray connector t...
Page 18 - For multiple stack redundancy, connect
Connect Media Gateways 18 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server 3. For multiple stack redundancy, connect the stacks using the black X330RC redundancy cable and the gray X330LC long cable: ● Connect the light gray connector of the black X330RC redundancy ...
Page 19 - Chapter 6: Install S8300 Media Server; From the front of the G700 Media
Issue 8 February 2007 19 Chapter 6: Install S8300 Media Server Note: Note: Complete these steps if you are installing an S8300 Media Server (configured as the primary controller or as a Local Survivable Processor). 1. From the front of the G700 Media Gateway, remove the blank faceplate from slot V1....
Page 21 - Chapter 7: Install Media and Expansion Modules
Issue 8 February 2007 21 Chapter 7: Install Media and Expansion Modules Note: Note: In each gateway, a single expansion module can be installed in the lower left slot only. If the S8300 is installed (in slot V1), up to 3 media modules can be installed in slots V2–V4. If no S8300 is installed, a four...
Page 23 - Chapter 8: Install USB Modem and CD-ROM Drive; USB Modem; not; USB
Issue 8 February 2007 23 Chapter 8: Install USB Modem and CD-ROM Drive USB Modem 1. Connect the USB cable to one of the USB ports on the faceplate of the S8300. 2. Following the instructions packaged with the modem, connect the other end of the USB cable to the modem. 3. Connect the analog telephone...
Page 25 - Chapter 9: Install UPS and Apply Power; AC power; Apply power to each media gateway
Issue 8 February 2007 25 Chapter 9: Install UPS and Apply Power UPS (AC only) 1. The UPS is an option for AC-powered gateways only. From the back of the G700 Media Gateway, connect the Uninterruptable Power Supply (UPS) using the manufacturer’s instructions. Note: Note: A stand-alone version of the ...
Page 26 - DC power
Install UPS and Apply Power 26 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server DC power 1. Apply power to each media gateway by connecting the DC power cord. Note: Note: There is no on/off switch. The units will power up when connected.
Page 27 - Chapter 10: Connect the Laptop — G700 without an; Connect the RJ45 end of a serial
Issue 8 February 2007 27 Chapter 10: Connect the Laptop — G700 without an S8300 This section assumes the G700 does not contain an S8300 Media Server. Use the Gateway Installation Wizard from the laptop to enter the initial gateway configuration parameters. 1. Connect the RJ45 end of a serial cable t...
Page 31 - To connect to the customer’s LAN
Issue 8 February 2007 31 14. Select Administrator Accounts from the menu, and add a super-user (SUSER) login. Assign the login to the suser login group of and the prof18 additional group. Note: Note: An SUSER group must be created before you can install the authentication file. The authentication fi...
Page 32 - To connect USB Modem; Connect the USB cable to either of the; Submit
Connect the Laptop — G700 with S8300 32 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server To connect USB Modem To configure the G700 and S8300 remotely, connect the USB modem. 1. Connect the USB cable to either of the two USB port on the faceplate of the S8300. 2. Fo...
