Avaya A800 - Manual
Avaya A800 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Network Topology; Interface setting
- Page 3 – Connecting the APs; Known Limitations; Text Style; Typed command; Via console; None
- Page 4 – Via the CLI; enable; Via the Web interface; Network Summary
- Page 5 – Initial Setup
- Page 6 – Assigning an IP to the Mobility Controller; Connecting APs; Provisioning APs
- Page 7 – SSID Configuration; CLI command configuration; Configuration
- Page 8 – Access Point Configuration; Preamble settings
- Page 9 – Channel and Tx power; Set to default
- Page 10 – CLI Commands; ESSID
- Page 11 – Short preamble; commands
- Page 12 – Web-based configuration; Basic Rates
- Page 13 – To assign the power and channel setting manually:
- Page 14 – Dynamic RF Management - ARM Aware Scanning; configure terminal; Security Policies and Quality of Service (QoS); The steps are as follows:
- Page 15 – Create an alias for the AVPP; Create policies for the wireless IP telephone user
- Page 16 – Assign policies to the role; Create a role, for example; phones; , and assign the policies to this role. This is the role that will
- Page 17 – Authentication
- Page 18 – CLI commands to set up subnet roaming; Configure terminal; NetLink Gateway
- Page 19 – Commands to verify setup for sub-net routing; From the Aruba 800:
- Page 20 – Checking the Configuration; The switch and AP are now ready for use with wireless IP telephones.
Configuration Guide
VIEW Certified
© Copyright 2007 Avaya, Inc. All rights reserved
21-601645, Issue 1, May 2007
Page 1
Aruba Mobility Controller
Configuration and Deployment Guide
SpectraLink’s Voice Interoperability for Enterprise Wireless (VIEW) Certification Program is
designed to ensure interoperability and high performance between wireless IP telephones and
WLAN infrastructure products. The products noted below have been thoroughly tested in
SpectraLink’s lab and have passed VIEW Certification. This document details how to configure
the Aruba mobility controller for use with wireless IP telephones.
Certified Product Summary
Manufacturer:
Aruba Networks:
Access Points
Approved products:
A200
A800
A2400
A6000 †
AP41
AP60
AP61
AP65
AP70 †
RF technology:
802.11b/g/a
Radio:
2.4 GHz (802.11 b/g), 5 GHz (802.11a)
Security :
WPA2-PSK
AP firmware version tested:
2.5.4.X
Handset models
3616/3620/3626
3641/3645
Radio
mode
802.11b
802.11b 802.11g 802.11a
Maximum telephone calls per AP:
12
12*
Network topology:
Switched Ethernet (recommended)
† Denotes products directly used in Certification Testing
* Maximum calls tested during VIEW Certification and the recommended setting in the AVPP. The certified product
may actually support a higher number of calls for 802.11a and 802.11g radio modes.
Service Information
If you encounter difficulties or have questions regarding the configuration process, please
contact Aruba Networks technical support at 1-800-943-4526, visit
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Aruba Mobility Controller Configuration Guide VIEW Certified Page 2 Network Topology The following topology was tested during VIEW Certification testing. Deployment Description It is required that voice users be placed on a separate VLAN (e.g., VLAN 10) and data users on a separate VLAN (e.g., VLAN ...
Aruba Mobility Controller Configuration Guide VIEW Certified Page 3 Connecting the APs The APs need an IP address for communication with the mobility controller. The APs can connect to the controller over a L2 or L3 network. Ensure that DHCP is enabled on the subnets the APs are connected to and can...
Aruba Mobility Controller Configuration Guide VIEW Certified Page 4 Via the CLI By default, only SSH (Secure SHell) access to the switch (mobility controller) is permitted. 1. From a management system that has network connectivity to the switch, connect to the switch using SSH: ssh admin@<switch ...
