Audiovox 128-7405B - Manual
Audiovox 128-7405B – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – To program these selectable features
- Page 4 – This Remote Start/Alarm System is designed to be used with; Automatic Transmission- Fuel Injection
- Page 5 – . If the diesel engine; INSTALLATION OF THE MAJOR COMPONENTS:; Do Not Mount The Module In The Engine Compartment
- Page 6 – STARTER INHIBIT RELAY:
- Page 7 – AUTOMATIC TRANSMISSIONS; only! Although this combination; IT MUST NOT; stalled into a vehicle with a; manually operated transmission; . Doing so may result in serious personal; Do not remove the fuse holders from this wire harness. Fuses must be
- Page 8 – Starter Output; YELLOW START WIRE DETAIL; Ignition 1 Output
- Page 9 – WIRING THE 4 PIN ALTERNATE IGNITION HARNESS; Parking Brake Input
- Page 10 – Siren Output; WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness; Parking Light Flasher Feed; Parking Light Wiring Detail
- Page 11 – Siren Wiring Detail; Positive Door Switch Wiring Detail; Ground Output While Running Under Remote Start Control
- Page 12 – General Motors VATS By-Pass Diagram; Entry Illumination Ground Output
- Page 13 – Entry Illumination Detail; Negative Inhibit Input Plus Trigger When Armed; Grey w/ Black Trace Negative Inhibit Safety Shut Down Detail; Ground When Armed Output
- Page 14 – Positive Inhibit Input Plus Trigger When Armed; Brake Switch Positive Shutdown Detail; Chassis Ground Source; Chassis Ground Connection Detail
- Page 15 – Tachometer Input Signal; Tachometer Input Wiring Detail; Negative Door Trigger; Negative Door Switch Wiring Detail; Delayed 300mA Pulsed Channel 3 Output
- Page 16 – Channel 3 Relay Wiring Detail; 00mA Latched Channel 4 Output
- Page 18 – Pin Transponder Control Output:; operates, see remote start feature # 10 for setting this output.; Pin Control Switch:; mating red two pin connector shell of the control module.; Pin Shock Sensor:; connector shell of the control module.
- Page 19 – Wire Positive Switched Door Lock/Unlock Wiring Detail; In this application, the; Wire Ground Switched Door Lock/Unlock Wiring Detail
- Page 21 – Door Lock Control Circuits; change, the above sequence will have to be followed.; TIMED START OPERATION:
- Page 22 – Programming Tach Rate:; NOTE: All applications require that tach be programmed.
- Page 24 – the ignition switch off. DO NOT attempt to remove the key.; MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:
- Page 27 – PIN IN VEHICLE DATA BUS PORT (IDB Port); COMPLETING THE INSTALLATION:; sure to clean the surface before affixing the label.
- Page 28 – WWW
128-7405B
1 of 28
Model APS-998
Installation Manual
The select
able features can be set manually as explained below
, or with the RF feature programmer
.
T
o
set features using the RF programmer
, follow the instructions p
ackaged with the programmer
.
Factory default settings are indicated by bold text.
Note :
The method of manual override can either be selected to operate from the valet switch or operate as custom code.
Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
NOTE: Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.
Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no s
election will be available.
RF Programmable Feature Bank 1 Is For T
ransmitter Programming See T
ransmitter Programming Guide.
RF Programmable Features Bank 2 Is Alarm Selectable Features:
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
5 Chirps
6 Chirps
1st DoorL/UL
1 Sec.
3.5
Sec.
1 Sec L, Dbl. U/L
Dbl L, 1 Sec UL
Dbl
L,
Dbl
UL
1
S
l/350mS
ul
2nd
Accy
Lock
Auto Lock On
Auto Lock Off
3rd
Accy
. UL
Auto
UL
Dr
.
Auto
UL
A
ll
Auto UL Off
4th Headlights
On
Arm
On
Disarm
On Both
Off
5th Passive
Locks
Passive
Active
6th Pass/Act
Arm
Passive Arm
Active Arm
7th Siren/Horn
Siren/Horn
Siren Only
Horn
Only
8th Horn Chirp
10mS
16mS
30mS
40mS
50mS
9th O/R Method
Custom
Code
V
alet
10th 2 S
tep U/L
O
n
Off
1
1th Chp Del
Tx
O
n
Off
12th V
olt
s/HdW
ire
Not A
vailable
13th Trigger Circuits
Not
A
vailable
14th L/UL Poll
Not A
vailable
When using the RF programmer
, enter the program mode as follows:
Turn the ignition on
Press and release valet switch 3 times
turn ignition off then on
Press and hold valet switch for 5 seconds
Siren chirps 2 times indicating access to RF feature program mode.
Action
System Response
Rev to "a" to add Fuses To Harness and PBLED 7/06
Rev to "b" to 136-4002 Updated F/W to add DBI Tach, Module Rev 6. 6-30-08
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-7405B 2 of 28 2 To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable...
128-7405B 4 of 28 4 Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote Start Selectable Features First Press the valet switch one tim...
128-7405B 5 of 28 Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat in addition to a "Wait To Start Input" either of which may be required forcertain diesel vehicles, (see selectable feature #11 Bank 3 &...
