Audiovox 128-8121 - Manual
Audiovox 128-8121 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 5 – This system is to be used in vehicles with; AUTOMATIC TRANSMISSIONS; personal injury and property damage.; MUST HAVE a Tach Signal Input, and an Automatic Transmission.
- Page 7 – SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output
- Page 8 – WIRING THE 4 PIN ALTERNATE IGNITION HARNESS; Parking Brake Input; Do not remove the fuse holders from this wire harness. Fuses must be
- Page 9 – Brake Switch Positive Shutdown Detail
- Page 11 – General Motors VATS By-Pass Diagram; Tach Sensor Input
- Page 12 – Diesel Wait To Start Input; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start; Pushbutton LED Programming Switch Assembly:
- Page 15 – Channel 3 Relay Wiring Detail
- Page 16 – Entry Illumination Detail; change, the above sequence will have to be followed.
- Page 18 – ignition switch off. DO NOT attempt to remove the key.
- Page 21 – sure to clean the surface before affixing the label.
- Page 23 – THIS PAGE LEFT BLANK INTENTIONALLY
128-8121
1 of 24
1
The select
able features can be set manually as explained below
, or with the RF feature programmer
.
T
o
set features using the RF programmer
, follow the instructions p
ackaged with the programmer
.
Factory default settings are indicated by bold text.
Note :
The method of manual override can either be selected to operate from the valet switch or operate as custom code.
Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
NOTE: Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.
Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no s
election will be available.
RF Programmable Feature Bank 1 Is For T
ransmitter Programming See T
ransmitter Programming Guide.
RF Programmable Features Bank 2 Is Alarm Selectable Features:
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
5 Chirps
6 Chirps
1st DoorL/UL
1 Sec.
3.5
Sec.
1 Sec L, Dbl. U/L
Dbl L, 1 Sec UL
Dbl
L,
Dbl
UL
1
S
l/350mS
ul
2nd
Accy
Lock
Auto Lock On
Auto Lock Off
3rd
Accy
. UL
Auto
UL
Dr
.
Auto
UL
A
ll
Auto UL Off
`
4th Headlights
Not Available
5th Passive Locks
Not Available
6th Pass/Act
Arm
Not Available
7th Siren/Horn
Not Available
8th Horn Chirp
10mS
16mS
30mS
40mS
50mS
9th O/R Method
Not Available
10th 2 S
tep U/L
O
n
Off
1
1th Chp Del
Tx
O
n
Off
12th Vlot Sense/Hd Wire
Not
A
vailable
13th Trigger Circuits
Not
A
vailable
14th L/UL Poll
Not A
vailable
15th
Aux Ch 5 Sel
Pulse
Push & Hold
1
0
S
e
c
2
0
S
e
c
Latch On/Off
Hold 3/S For O/P
16th
Aux Ch 6 Sel
Pulse
Push & Hold
1
0
S
e
c
2
0
S
e
c
Latch On/Off
Hold 3/S For O/P
17th
Aux Ch 7 Sel
Pulse
Push & Hold
1
0
S
e
c
2
0
S
e
c
Latch On/Off
Hold 3/S For O/P
18th Trigger Delay
Not Available
When using the RF programmer
, enter the program mode as follows:
Turn the ignition on.
Press and release valet switch 3 times;
turn ignition off then on.
Press and hold valet switch for 5 seconds.
Siren and or lights chirp/flash 2 times indicating access to RF feature program mode.
Model APS-687a
Installation Manual
From APS687 Change Transmitters to 07SP 05/07 add door lock
s e c t i o n
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-8121 5 of 24 5 This system is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this combina- tion Keyless Entry/Remote Start unit is a sophisticated system with many advanced features, IT MUST NOT be installed into a vehicle with a manually operated transmission. Doing so may r...
128-8121 7 of 24 7 Note: This wire must be connected to the vehicle side of the starter cut relay (when used). For theelectrical neutral switch configuration, this connection must be made between the starter inhibitrelay, (when used) and the neutral safety switch as shown in the following diagram. F...
128-8121 8 of 24 8 WIRING THE 4 PIN ALTERNATE IGNITION HARNESS ORANGE/BLACK Wire: Parking Brake Input This wire is used only when the turbo timer mode, Bank 3, feature # 16 is selected ON. This input insuresthat the vehicle parking brake is applied whenever the vehicle is set up for and the turbo ti...
