Audiovox PRO-9675FT - Manual
Audiovox PRO-9675FT – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION OF THE MAJOR COMPONENTS:; HOOD AND TRUNK PIN SWITCHES:
- Page 5 – Yellow Start Wire Detail
- Page 6 – WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness; Parking Light Flasher Feed; Parking Light Wiring Detail
- Page 8 – General Motors VATS By-Pass Diagram
- Page 9 – Entry Illumination Ground Output; Entry Illumination Detail; Negative Inhibit Input; Grey w/ Black Trace Negative Inhibit Safety Shut Down Detail
- Page 10 – Brake Switch Positive Shutdown Detail
- Page 11 – Chassis Ground Source; Chassis Ground Connection Detail; Tachometer Input Signal; Tachometer Input Wiring Detail; Negative Door Trigger; Negative Door Switch Wiring Detail
- Page 12 – Channel 2 Relay Wiring Detail; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS
- Page 14 – switch to the factory door lock relay. See Below For Wiring Detail.
- Page 15 – TIMED START OPERATION:
- Page 16 – REMOTE START SELECTABLE FEATURES
- Page 20 – METHOD 1; To connect to the key in sensor as shown in method 1:
- Page 21 – METHOD 2; To connect to the key in sensor circuit as shown for method 2:; COMPLETING THE INSTALLATION:; Make sure to clean the surface before affixing the label.
- Page 22 – WIRING DIAGRAM
4 Channel Remote Car Starter
With Full Feature Alarm System
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems,
Gasoline or Diesel With True Tach Reference
And Automatic Transmissions Only.
Kit Contents:
Remote Start/Alarm Control Module
(2) - Three Button Anti Code Grabbing Transmitters
3 Channel Code Learning Receiver
External Superheterodyne Antenna/Receiver
Six Tone Siren
(1) - Multi Pin Input/Output Harness
(1) - Six Pin Power Harness
(1) - Four Pin Auxiliary Output Harness
(1) - Two Pin LED Indicator
(1) - Two Pin Valet / Programming Switch
(1) - Two Pin Control Switch
(1) - Four Pin Shock Sensor Harness
(1) - Two Pin Door Lock Harness
(1) - Dual Stage Shock Sensor
(1) - Starter Inhibit Relay and Socket
(2) - 30 Amp In-line Fuse Holders With Fuses
(1) - Pin Switch Hardware Bag
(2) - Under Hood Caution Labels
(1) - Installation Manual
(1) - Operator's Manual
(1) - Limited Warranty
(2) - Window Decals
128-5371
1 of 22
Model PRO-9675FT
Installation Manual
Released 8-20-98
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
The PRO-9675 Remote Start/Alarm System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel...
BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when theignition key is turned to the to the "ON" or "RUN" and the "START" or CRANK" positions, and will have0 volts when the key is turned to the...
WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red Trace Wire: Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay. If the vehicle you are workingon has +12 volt switched parking lights, connect this wire to a fused + 12 volt ...
