Audiovox PRO-9675FT - Manuals

Page 2 - INSTALLATION OF THE MAJOR COMPONENTS:; HOOD AND TRUNK PIN SWITCHES:

The PRO-9675 Remote Start/Alarm System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel...

Page 5 - Yellow Start Wire Detail

BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when theignition key is turned to the to the "ON" or "RUN" and the "START" or CRANK" positions, and will have0 volts when the key is turned to the...

Page 6 - WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness; Parking Light Flasher Feed; Parking Light Wiring Detail

WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red Trace Wire: Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay. If the vehicle you are workingon has +12 volt switched parking lights, connect this wire to a fused + 12 volt ...

Page 8 - General Motors VATS By-Pass Diagram

General Motors VATS By-Pass Diagram Light Blue Wire: Ignition 3 Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of the...

Page 9 - Entry Illumination Ground Output; Entry Illumination Detail; Negative Inhibit Input; Grey w/ Black Trace Negative Inhibit Safety Shut Down Detail

Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm thealarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. Thiswire should be connected to an ext...

Page 10 - Brake Switch Positive Shutdown Detail

Orange Wire: Ground When Armed Output This wire provides a 300mA ground output when the alarm circuit is armed to control the starter inhibitrelay. Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85(red wire) of the relay to an ignition wire in the vehi...

Page 11 - Chassis Ground Source; Chassis Ground Connection Detail; Tachometer Input Signal; Tachometer Input Wiring Detail; Negative Door Trigger; Negative Door Switch Wiring Detail

Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Becertain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. Chassis Ground Connection Detail Green w/ Orange Trace Wir...

Page 12 - Channel 2 Relay Wiring Detail; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS

Dark Blue Wire: Delayed 300mA Pulsed Channel 2 Output The Dark Blue wire supplies a 300mA ground pulsed output whenever channel two of the receiver is accessed.Pressing the pre-programmed transmitter button for three seconds will access channel two. This is a lowcurrent output and must be connected ...

Page 14 - switch to the factory door lock relay. See Below For Wiring Detail.

3 Wire Positive Switched Door Lock/Unlock Wiring Detail 14 3 Wire Ground Switched Door Lock/Unlock Wiring Detail 128-5371 14 of 22 To Red Lock WireOf Control Module To Green Unlock WireOf Control Module 3 Wire Positive Switched Door Locks: In this application, the Red wire of the two pin harness pro...

Page 15 - TIMED START OPERATION:

LED Flash Pattern 1 Flash Pause etc. 2 Flash Pause etc. 3 Flash Pause etc. 4 Flash Pause etc. 5 Flash Pause etc. First Second Third Fourth Fifth Action Turn the ignition switch onFlip the valet/program switch on then off 3 timesWithin 3 seconds, turn the ignition switch offand then on. Press the tra...

Page 16 - REMOTE START SELECTABLE FEATURES

REMOTE START SELECTABLE FEATURES RF Programmable Features: LED Pattern1 x Pause etc.2 x Pause etc.3 x Pause etc.4 x Pause etc.5 x Pause etc.6 x Pause etc.7 x Pause etc.8 x Pause etc.9 x Pause etc.10 x Pause etc. DefaultOff10 MinutesSteadyTach----------------Off during crankOff---------------Gasoline...

Page 20 - METHOD 1; To connect to the key in sensor as shown in method 1:

KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will prevent the vehicle with a Mechanical ...

Page 21 - METHOD 2; To connect to the key in sensor circuit as shown for method 2:; COMPLETING THE INSTALLATION:; Make sure to clean the surface before affixing the label.

METHOD 2 To connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.B. Cut this wire and connect the ignition cylinder side to chassis ground.C. Locate the key in sensor switch wire that connects the...

Page 22 - WIRING DIAGRAM