Audiovox 128-7405B - Manuals

Audiovox 128-7405B – Manual in PDF format online.

Manuals:

Manual

Manual Audiovox 128-7405B

Summary

Page 2 - To program these selectable features

128-7405B 2 of 28 2 To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Selectable...

Page 4 - This Remote Start/Alarm System is designed to be used with; Automatic Transmission- Fuel Injection

128-7405B 4 of 28 4 Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote Start Selectable Features First Press the valet switch one tim...

Page 5 - . If the diesel engine; INSTALLATION OF THE MAJOR COMPONENTS:; Do Not Mount The Module In The Engine Compartment

128-7405B 5 of 28 Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat in addition to a "Wait To Start Input" either of which may be required forcertain diesel vehicles, (see selectable feature #11 Bank 3 &...

Page 6 - STARTER INHIBIT RELAY:

128-7405B 6 of 28 DASH MOUNTED LED: The small LED included in the kit will serve as a visual indicator of the alarm's status and provide a visualdeterrent to a potential thief. The LED also provides important feed back information during the transmitterand feature program modes. The LED should be in...

Page 7 - AUTOMATIC TRANSMISSIONS; only! Although this combination; IT MUST NOT; stalled into a vehicle with a; manually operated transmission; . Doing so may result in serious personal; Do not remove the fuse holders from this wire harness. Fuses must be

128-7405B 7 of 28 relay to an existing harness in the chosen location using a cable tie around the relay's wiring harness. CAUTION! Do not wire tie the metal bracket to an existing wiring harness as vibration may cause chaffing and shorting damaging the factory wiring. If an existing harness is not ...

Page 8 - Starter Output; YELLOW START WIRE DETAIL; Ignition 1 Output

128-7405B 8 of 28 IMPORTANT! It is the responsibility of the installing technician to determine the load factor of the vehicles electricalcircuits when the vehicle is running, and to adequately fuse the two power wires based on that load. If thevehicle, running under load with the air conditioner, h...

Page 9 - WIRING THE 4 PIN ALTERNATE IGNITION HARNESS; Parking Brake Input

128-7405B 9 of 28 GREEN Wire: Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when theignition key is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position.This wire will s...

Page 10 - Siren Output; WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness; Parking Light Flasher Feed; Parking Light Wiring Detail

128-7405B 10 of 28 White w/ Black Trace Wire: (+) Siren Output This is the positive siren feed wire. Route this wire through a grommet in the firewall to the sirenlocation. Connect the White w/ Black Trace wire to the Red wire of the Siren. Secure the Black wireof the Siren to a known chassis ground...

Page 11 - Siren Wiring Detail; Positive Door Switch Wiring Detail; Ground Output While Running Under Remote Start Control

128-7405B 11 of 28 Siren Wiring Detail 11 (-) TO VEHICLE'S CHASSIS GROUND TO WHITE w/BLACK WIRE OF MODULE Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches + 12 volts when the door is opened, (Some Fords and someImports), you must connect this wire to the positive out...

Page 12 - General Motors VATS By-Pass Diagram; Entry Illumination Ground Output

128-7405B 12 of 28 A. Shock Sensor By Pass: If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during theRemote Start activation period, then vibration from the running vehicle can cause the alarm to trigger. Inthis case, connect the Light Blue Wire to terminal #...

Page 13 - Entry Illumination Detail; Negative Inhibit Input Plus Trigger When Armed; Grey w/ Black Trace Negative Inhibit Safety Shut Down Detail; Ground When Armed Output

128-7405B 13 of 28 1 3 Entry Illumination Detail Grey w/ Black Trace Wire: Negative Inhibit Input Plus Trigger When Armed The Grey w/ Black Trace wire provides an instant shutdown for the Remote Start Control Module wheneverit is grounded also trigger for the alarm when armed. Connect the Grey w/ Bl...

Page 14 - Positive Inhibit Input Plus Trigger When Armed; Brake Switch Positive Shutdown Detail; Chassis Ground Source; Chassis Ground Connection Detail

128-7405B 14 of 28 Brown w/ Black Trace Wire: Positive Inhibit Input Plus Trigger When Armed The Brown w/ Black Trace wire provides an instant shutdown for the Remote Start Control module when-ever it gets + 12 volts also triggers the alarm when armed. If the Brake lights switch in the vehicleswitch...

Page 15 - Tachometer Input Signal; Tachometer Input Wiring Detail; Negative Door Trigger; Negative Door Switch Wiring Detail; Delayed 300mA Pulsed Channel 3 Output

128-7405B 15 of 28 1 5 Green w/ Orange Trace Wire: Tachometer Input Signal This wire will continually monitor the engine's tach rate while the unit is under power of the Remote Startmodule. This wire will be routed to the vehicle ECM tach input or through the firewall into the enginecompartment and ...

Page 16 - Channel 3 Relay Wiring Detail; 00mA Latched Channel 4 Output

128-7405B 16 of 28 Channel 3 Relay Wiring Detail 1 6 Green w/ Black Trace Wire: 300mA Latched Channel 4 Output The Green w/ Black Trace wire supplies a 300 mA switched output whenever channel four of the receiveris accessed. Pressing the pre-programmed transmitter button(s) will access channel four ...

Page 18 - Pin Transponder Control Output:; operates, see remote start feature # 10 for setting this output.; Pin Control Switch:; mating red two pin connector shell of the control module.; Pin Shock Sensor:; connector shell of the control module.

128-7405B 18 of 28 1 8 Black w/ Yellow Trace Wire: Ground Output During Start (Crank) The Black w/ Yellow Trace wire will provide a 300 mA ground output while the starter output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb Test wire found in some GM vehi...

Page 19 - Wire Positive Switched Door Lock/Unlock Wiring Detail; In this application, the; Wire Ground Switched Door Lock/Unlock Wiring Detail

128-7405B 19 of 28 1 9 3 Wire Positive Switched Door Locks: In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the disarmingsequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire fromthe factory door unlock swi...

Page 21 - Door Lock Control Circuits; change, the above sequence will have to be followed.; TIMED START OPERATION:

128-7405B 21 of 28 2 1 NOTE: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, orfor convenience, a Door Lock Interface. Refer to the...

Page 22 - Programming Tach Rate:; NOTE: All applications require that tach be programmed.

128-7405B 22 of 28 2 2 TEMPERATURE START: When Temperature Start, Bank 3 feature #13 is selected on, the temperature start mode can be activatedfrom the transmitter. See owners manual for turning this feature on from the transmitter. Once activated,the unit will start 1 time if the vehicle temperatu...

Page 24 - the ignition switch off. DO NOT attempt to remove the key.; MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:

128-7405B 24 of 28 If the unit fails this test, recheck your enable switch connection to the Ground and the Black/White wire ofthe Audiovox Remote Start Unit. If you have a plug in enable switch, check that the two pin connector isfirmly seated in the mating connector on the control module. DO NOT R...

Page 27 - PIN IN VEHICLE DATA BUS PORT (IDB Port); COMPLETING THE INSTALLATION:; sure to clean the surface before affixing the label.

128-7405B 27 of 28 2 7 be connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, becertain to use the dual diode assembly packaged with the Audiovox Remote Start Unit as shown in thisinstallation guide. (Page 9) AFTER THE CONNECTION OF THE NEUTRAL START SAF...

Page 28 - WWW