AT&T 929 - Manual

3 Installation Table/desk installation Install the desk/table bracket to the upper portion on the telephone base. Plug the tabs on the bracket into the slots on the telephone base until they click into place. Install batteries to provide power for the AUDIO ASSIST , MUTE and lights. Press the batter...

4 Set the tone/pulse switch. If you have touch tone service, set the switch to TT (tone). If you have dial pulse (rotary) service, set the switch to DP (pulse). Connect the handset to the telephone. Plug the handset coiled cord into the handset jack on the left side of the telephone base. Plug the o...

5 Wall installation Install the wall bracket to the lower portion on the bottom of the telephone base. Plug the tabs on the bracket into the slots on the telephone base until they click into place. Install batteries to provide power for the AUDIO ASSIST , MUTE and lights. Press the battery cover tab...

6 Installation Set the tone/pulse switch. If you have touch tone service, set the switch to TT (tone). If you have dial pulse (rotary) service, set the switch to DP (pulse).Connect the telephone line cord to the telephone. Plug the telephone line cord into the jack labeled LINE IN and route it into ...

7 Reverse the handset tab. This tab holds the handset when you hang up. Hold down the switchhook and slide the tab up and out of its slot. Turn the tab so that the end with the hook is up. Then hold down the switchhook while you insert the tab back into its slot. Connect the handset to the telephone...

11 Telephone memory This telephone can store 13 telephone numbers, each up to 16 digits. You can dial numbers stored in memory by pressing one or two buttons. Directory card Lift the plastic cover off the directory c a r d t o w r i t e d o w n t h e n u m b e r s and names which are stored in the t...

12 Store a pause in a memory number Press REDIAL/PAUSE once to store a three to four second pause in the dialing sequence. Each additional press will add another three to four second pause. NOTE: Each three to four second pause is counted as one digit when storing numbers in the telephone memory. Di...

13 General product care To keep your telephone working and looking good, follow these guidelines: Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).DO NOT expose it to direct sunlight or moisture.Avoid dropping the telephon...

14 T h e te le p h o n e does not ring • Make sure the RINGER switch is not set to OFF . • I f t h e re a re s e ve ra l o t h e r te le p h o n e s c o n n e c t e d o n t h e s a m e l i n e , t r y disconnecting some of them. Having too m a n y te le p h o n e s co n n e c te d c a n a l s o crea...

15 Troubleshooting Cannot store telephone numbers in memory • Make sure you are pressing the correct sequence of buttons when storing numbers (see pages 11 and 12). • Make sure you have installed three fully c h a rg e d A A b a t t e r i e s ( n o t i n c l u d e d ) following the polarity guide in...

16 Technical specifications REN 1.5B Power Line feed voltage 48V +/- 2V Line loop current 18mA to 100mA Ringer levels Off = 0dB HI = 85dB Compliance FCC and UL approved Memory One-touch memory: 3 memory locations, 16 digits per location Two-touch memory: 10 memory locations, 16 digits per location A...

17 A Answer a call 8 Audio assist 10 B Batteries 3, 5 D Directory card 11 E End a call 8Erase redial 9 F Flash 9 H Handset tab 7Handset volume 10 M Make a call 8Memory 11Mute 8 N No dial tone 14 O One-touch memory 12 P Pause 12 R Redial 9Ringing indicator 8Ringer volume 10 S Speakerphone 8 T Tempora...