AEG GYB00416UT Installation Manual

Page 2 - CONTENTS; Visit our website to:; Register your product for better service:; FOR PERFECT RESULTS; Subject to change without notice.

B www.aeg.com 1. INTRODUCTION ..............................................................................................1 2. SAFETY INFORMATION ..................................................................................2 3. PRODUCT DESCRIPTION ................................................

Page 3 - Intended use and; INTRODUCTION

1 ENGLISH 1.1 Intended use and unintended use This AEG appliance is intended to be used to store, heat and provide drinking water. The appliance should only be used in household and similar environments, such as: • In shops, offices and other similar working environments; • In farm houses; • By clie...

Page 4 - SAFETY INFORMATION; Children and vulnerable

2 www.aeg.com 1.3 Article numbers The table below describes the available components of the appliance. Main parts Type Article number Boiler 4 litres GYB00416UT 8 litres GYB00816UT Tap Curve – Chrome finish GYT11012CB Square – Chrome finish GYT12012CB Curve – Stainless steel finish GYT11012SB Square...

Page 5 - Electrical connection

3 ENGLISH • Children must be supervised to ensure that they do not play with the appliance. • The appliance contains hot parts. Ensure that children do not have access to the appliance and lock possible access doors. • Keep all packaging away from children. 2.3 Installation • Only qualified, certifi...

Page 6 - com; Care and cleaning

4 www.aeg.com 2.6 Pressure safety valve installation • Leave the outlet of the pressure-relief device open to the atmosphere so water may drip from the discharge pipe. 2.7 Filter installation • Always read the instruction manual supplied with the filter. • A filter can be installed to reduce the har...

Page 7 - Procedure in the event; Part; PRODUCT DESCRIPTION

5 ENGLISH 2.11 Procedure in the event of breaks in operation • After a break in operation exceeding two days (weekend, holiday, etc.), the appliance must be flushed with 4 or 8 litres of water before being reused, depending on the capacity of your boiler. • After a shutdown of 4 weeks or more, the f...

Page 10 - INSTALLATION; Important installation information; Before installation; Step

8 www.aeg.com 4. INSTALLATION 4.1 Important installation information • Read and follow all instructions in the SAFETY INFORMATION section. • Refer to the separate manuals supplied with the other components for more relevant information. 4.2 Before installation Step Action 1 Make sure that you have t...

Page 11 - Installing the appliance

9 ENGLISH 4.3 Installing the appliance Step Action 1 Determine which configuration you are going to install. The appliance is available for 2 different configurations: • Solo situation (see image 4) • Combi situation (see image 5) The solo configuration supplies only boiling water. Warm water comes ...

Page 14 - Filling the appliance with water

12 www.aeg.com Step Action 1 Make sure all connections are tightened properly to prevent leakages. 2 If the mixing valve is (D) installed, set the temperature with the temperature regulator (34). 3 Make sure the valve (16) on the pressure safety valve is in the OPEN position. 4 Open the cold water s...

Page 15 - Important operation information; DAILY USE; Starting the boiler

13 ENGLISH 5.1 Important operation information • Read and follow all instructions in the SAFETY INFORMATION section. • Refer to the separate manuals supplied with the other components for other relevant information. • The amount of boiling water provided is limited by the size of your boiler. When n...

Page 17 - MAINTENANCE, CARE AND CLEANING; Important care and cleaning information; Task; Important trouble shooting information

15 ENGLISH 6. MAINTENANCE, CARE AND CLEANING 7. TROUBLESHOOTING 6.1 Important care and cleaning information • Read and follow all instructions in the SAFETY INFORMATION section. • Refer to the separate manuals supplied with the other components for other relevant care and cleaning information. 6.2 F...

Page 19 - TECHNICAL INFORMATION; Important other technical information

17 ENGLISH Problem Cause Solution Flow rate too high. Too much pressure. • Close the valve of the pressure safety valve (23) or the cold water supply valve. • Place a pressure reducing valve. Water drips from the discharge pipe or the pressure- relief device. • Replace the expansion vessel. 8. TECHN...

Page 21 - Image 1

19 ENGLISH www.aeg.com Image 1 Main components of the complete system B E C D A

Page 22 - Image 2

20 www.aeg.com IMAGES 6 7 8 10 11 12 13 9 4 1 2 3 5 Image 2 Parts description

Page 25 - Image 3

Page 26 - Image 4

24 www.aeg.com Image 4 Overview Solo Situation IMAGES

Page 27 - Image 5

Page 28 - Image 6

Page 29 - Image 7

Page 30 - Image 8; Image 9

28 www.aeg.com Image 8 Attach t-piece to cold water supply Image 9 Place discharge connection on siphon IMAGES