Zip MT2792Z10 - User Manual
Zip MT2792Z10 Faucet – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Cut a 35mm hole in the bench / sink; Tap assembly exploded view and kitchen layout side view.
- Page 3 – Installation Instructions; Note
- Page 4 – To change the spout position
- Page 5 – Left Hand Control; Height adjustment
- Page 6 – - Mixer Tap Installation
- Page 7 – Installing the Mixer Tap; Arc Mixer Tap; Fit the lower rubber seal to the threaded extension.
- Page 8 – RED
- Page 9 – : make sure the tap location will allow the; Installation; sealant to ensure a watertight seal; Installation Procedure
- Page 10 – AIO Vented assy; BLUE; AIO Mains assy; Clamp Block markings and silicon tube positions,
- Page 11 – Vented
- Page 12 – Restrictaflow valve
- Page 13 – Special Tools Required:
- Page 14 – Trim all plastic tubes to min-
- Page 15 – Plumbing Connection
- Page 17 – In addition to normal tools, the following will be required:; Tap Installation; Taps are available with ARC or CUBE neck options.; Double Bowl
- Page 18 – Chilled Sparkling Tap components; CSHA Tap connections
- Page 19 – BHA and CHA Tap connections
- Page 20 – NZ Office
803341 - Tap Installation Instructions - 02.17 - v2.02
Page 1 of 20
116
BC HydroTap Classic
Single
Bowl
For
Elite,Classic
and Arc/Cube
35mm hole
For
A-I-O 50mm and
Mixer taps 35mm
hole
Double Bowl
HydroTap Taps Installation
Hole positioning:
Position the tap such that it dispenses into the sink bowl with ample clearance for a cup or tea pot.
Alternatively, the tap could be mounted away from the sink using a font, available as an accessory.
TAP
Recommended dispensing distance **
Elite
116 mm
HydroTap Classic
116 mm
HydroTap Arc/Cube
171 - 174 mm (Extended)
Classic All-In-One
211 mm
Celsius All-In-One
242 - 250 mm
Celsius Arc/Cube
220 mm
Mixer - Arc neck
220 mm
Mixer - Classic
270 mm
Mixer - Cube neck
220 mm
For new installations, It is recommended to fit the tap prior to installing the undersink unit.
Note:
This book must be read in conjunction with the undersink installation manual and the user manual
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 Apply a light smearing of silicon sealant on the underside of the spacer to ensure a watertight fit. 1.2 Cut a 35mm hole in the bench / sink top. BENCH TOP 1.1 Ø35mm ALL THREAD ROD STAINLESS STEEL SPACER SPIDER CLAMP NUT BLACK PLAST...
803341 - Tap Installation Instructions - 02.17 - v2.02 Page 3 of 20 BLACK PLASTIC SPACER 1.3 Installation Instructions Pass all the hoses, tubes and USB lead through the 35mm hole. 1.4 35mm hole Note Note : feed each of the three tubes and electrical cable evenly in between the legs of the SPIDER CL...
Page 4 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 2 - HydroTap Arc/Cube The HydroTap Arc/Cube has a spout that may be fixed in one of 6 angular positions (depending on the position of the rotary control) and fixed in one of two height positions. The spout is fixed and does not swiv...
