Zip MT2792Z10 - Manuals

Zip MT2792Z10 Faucet – User Manual in PDF format online.

Manuals:

User Manual

User Manual Zip MT2792Z10

Summary

Page 2 - Cut a 35mm hole in the bench / sink; Tap assembly exploded view and kitchen layout side view.

Page 2 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 Apply a light smearing of silicon sealant on the underside of the spacer to ensure a watertight fit. 1.2 Cut a 35mm hole in the bench / sink top. BENCH TOP 1.1 Ø35mm ALL THREAD ROD STAINLESS STEEL SPACER SPIDER CLAMP NUT BLACK PLAST...

Page 3 - Installation Instructions; Note

803341 - Tap Installation Instructions - 02.17 - v2.02 Page 3 of 20 BLACK PLASTIC SPACER 1.3 Installation Instructions Pass all the hoses, tubes and USB lead through the 35mm hole. 1.4 35mm hole Note Note : feed each of the three tubes and electrical cable evenly in between the legs of the SPIDER CL...

Page 4 - To change the spout position

Page 4 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 2 - HydroTap Arc/Cube The HydroTap Arc/Cube has a spout that may be fixed in one of 6 angular positions (depending on the position of the rotary control) and fixed in one of two height positions. The spout is fixed and does not swiv...

Page 5 - Left Hand Control; Height adjustment

803341 - Tap Installation Instructions - 02.17 - v2.02 Page 5 of 20 Installation Instructions A A Left Hand Control Right Hand Control B C C B 50mm Height adjustment (Fixed position options) Angular adjustment (Fixed position options) 2.2 O-RING LOWER RUBBER WASHER WASHER NUT 2.3 2.4 Mounting (See t...

Page 6 - - Mixer Tap Installation

Page 6 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 Cut a 35mm hole in the bench / sink top. SINK TOP 3.1 35mm Note: make sure the tap location will allow the nozzle to drain into the sink. Tap assembly exploded view and kitchen layout side view. BRAIDED HOSE x 3 3 - Mixer Tap Instal...

Page 7 - Installing the Mixer Tap; Arc Mixer Tap; Fit the lower rubber seal to the threaded extension.

803341 - Tap Installation Instructions - 02.17 - v2.02 Page 7 of 20 3.3 Installing the Mixer Tap (Classic, Arc and Cube) Installation Instructions Sink top O-ring Lower seal Washer Securing nut Mixer tap Arc Mixer Tap • Fit the O-ring into the recess on the underside of the Mixer tap. (Note: If moun...

Page 8 - RED

Page 8 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 Installation Instructions 3.4 COLD isolation valve (Not supplied) HydroTap Mixer Connections RED CLEAR BLUE WHITE Restrictafl ow valve (Supplied) Typical HydroTap 4-in-1 Installation (see section 5) Tee piece (Supplied) POWER CORD U...

Page 9 - : make sure the tap location will allow the; Installation; sealant to ensure a watertight seal; Installation Procedure

803341 - Tap Installation Instructions - 02.17 - v2.02 Page 9 of 20 Cut a 50mm hole in the bench / sink top. SINK TOP 4.1 50mm Note Note : make sure the tap location will allow the nozzle to drain into the sink. (See Page 11) 4 - Classic All-In-One Tap Installation Min 300mm 335mm 470mm 4.2 • Fit th...

Page 10 - AIO Vented assy; BLUE; AIO Mains assy; Clamp Block markings and silicon tube positions,

Page 10 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 FIXING NUT 4.3 Installation Instructions 4.4 CLAMP BLOCK O-RING AIO Vented assy BLUE to Chiller connection CLEAR to vent RED to Boiling connection From Mixer OUT AIO Mains assy BLUE mark WHITE mark BLUE mark RED mark Clamp Block ma...

Page 11 - Vented

803341 - Tap Installation Instructions - 02.17 - v2.02 Page 11 of 20 4.5 Installation Instructions CLAMP BLOCK • Screw the braided hoses into the extension tubes. Ensure the o-rings are lubricated prior to assembly and that the braided hoses, with coloured markings, are correctly matched with the co...

Page 12 - Restrictaflow valve

Page 12 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 Installation Instructions 4.7 Typical All-In-One Vented assembly with Booster heater (See section 5) Booster BC Unit A-I-O Tap 400mm 335mm Restrictaflow valve & Tee piece (Supplied) Note: The All-In-One vented taps require a Re...

Page 13 - Special Tools Required:

803341 - Tap Installation Instructions - 02.17 - v2.02 Page 13 of 20 5.1 5 - Celsius All-In-One Tap Installation 464 Clearance Min 300mm 335mm Cut a 50mm hole in the bench / sink top. Note: make sure the tap location will allow the nozzle to drain into the sink 5.2 BENCH TOP Ø 50mm Special Tools Req...

Page 14 - Trim all plastic tubes to min-

Page 14 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 Installation Instructions +RW &ROG :DWHU2XWOHW &KLOOHG:DWHU 2XWOHW %RLOLQJ:DWHU 2XWOHW 6WHDP9HQW 2XWOHW 42.9 85 439.5 258 255 220mm (Hot & Cold Outlet) Swing Swing 151 Underside of spout of Celisus AIO tap. 5.4 5.5 Note...

Page 15 - Plumbing Connection

803341 - Tap Installation Instructions - 02.17 - v2.02 Page 15 of 20 Installation Instructions BRASS NUT USB PLUG FROM BOILING OUTLET AT BASE UNIT OR COMMAND CENTRE 5.6 Plumbing Connection COLD MAINS HOT MAINS JG STRAIGHT CONNECTOR BRAIDED HOSE FOR MIXED WATER FROM CHILLED OUTLET AT BASE UNIT OR COM...

Page 17 - In addition to normal tools, the following will be required:; Tap Installation; Taps are available with ARC or CUBE neck options.; Double Bowl

803341 - Tap Installation Instructions - 02.17 - v2.02 Page 17 of 20 Special Tools Required: In addition to normal tools, the following will be required: • 35mm diameter sheet metal hole punch for sink tops. (Not supplied) • 35mm diameter hole saw for timber bench tops. (Not supplied) • 42mm AF tube...

Page 18 - Chilled Sparkling Tap components; CSHA Tap connections

Page 18 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 Cut a 35mm hole in the bench / sink top. BENCH TOP 6.1 Ø35mm HOT & COLD BRAIDED HOSES CHILLED TUBE BRASS WASHER BLACK RUBBER Seal BRASS NUT USB PLUG SPARKLING TUBE JG Y-PIECE Note: Trim all plastic tubes to minimise any dead le...

Page 19 - BHA and CHA Tap connections

803341 - Tap Installation Instructions - 02.17 - v2.02 Page 19 of 20 HOT & COLD BRAIDED HOSES BOILING or CHILLED TUBE BRASS WASHER BLACK RUBBER SEAL BRASS NUT VENT TUBE USB PLUG BHA and CHA Tap connections RUBBER Washer Boiling model Vent outlet 6.3

Page 20 - NZ Office

Page 20 of 20 803341 - Tap Installation Instructions - 02.17 - v2.02 • Pass all the hoses, tubes and USB lead through the 35mm hole. • Ensure the black rubber seal is correctly positioned to give a water tight seal • Secure the rubber & brass washers and large nut from inside the cupboard space,...