York B3CH 048 and 060 - Manual
York B3CH 048 and 060 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – FIGURES; No. Description Page; TABLE OF CONTENTS
- Page 3 – INSTALLATION
- Page 5 – TABLE 2 - AIR FLOW LIMITATIONS
- Page 6 – OPTIONAL ECONOMIZER RAIN HOOD; NOTE: Sensor must be positioned so that the sensing ports
- Page 7 – TABLE 3 - PHYSICAL DATA; Basic Unit
- Page 8 – OUTDOOR COIL; UTILITIES ENTRY DATA
- Page 9 – REAR VIEW
- Page 10 – TABLE 4 - SUPPLY AIR PERFORMANCE - BCH048; TABLE 5 - SUPPLY BLOWER PERFORMANCE - BCH060
- Page 12 – NOTE: Prior to each cooling season, the crankcase heater; COOLING SEQUENCE OF OPERATION; CONTROL; OPERATION
- Page 13 – LOCKOUT CONTROL; minute delay before starting.; CHECKING SUPPLY AIRFLOW; NOTE: The tubes must be inserted and held in a position per-
- Page 14 – NORMAL MAINTENANCE; CAUTION: Prior to any of the following maintenance proce-; MAINTENANCE
GENERAL
YORK Model BCH units are single package heat pumps
designed for outdoor installation on a rooftop or a slab.
Supplemental electric heaters are available as field-installed
accessories. The units are manufactured under ISO 9002
Quality System Certification.
Units are completely assembled on rigid, permanently
attached base rails. All piping, refrigerant charge, and electrical
wiring is factory-installed and tested. The units require only
electric power and duct connections at the point of installation.
The supplemental electric heaters have nickel-chrome
elements and utilize single point power connection.
INSPECTION
As soon as a unit is received, it should be inspected for possible
damage during transit. If damage is evident, the extent of the
damage should be noted on the carrier's freight bill. A separate
request for inspection by the carrier's agent should be made in
writing. See local distributor for additional information.
REFERENCE
Additional information on the design, installation, operation
and service of this equipment is available in the following
reference forms:
•
55.70-N1
-General Installation
•
55.70-N2
-Pre-start & Post-start Check List
•
530.18-N1.2V
-Economizer Accessory
•
530.18-N1.4V
-Fixed Outdoor Air Damper Accessory
•
530.18-N1.6V
-Motorized Outdoor Air Damper Accy.
•
530.18-N7.1V
-Electric Heater Accessory
•
530.18-N7.2V
-Fuse Block Accessory
Renewal Parts:
•
Refer to Parts Manual for complete listing of replacement
parts on this equipment.
All forms referenced in this instruction may be ordered from:
Standard Register
Toll Free Tel: (405) 691-1126
Toll Free Fax: (405) 799-7746
APPROVALS
These units are designed and manufactured as follows:
1. For use as a heat pump only unit or a heat pump unit with
supplemental electric heat.
2. For outdoor installation only.
®
SUNLINE 2000
SINGLE PACKAGE HEAT PUMPS
INSTALLATION INSTRUCTION
Supersedes: 511.13-N1YI (900)/035-12984-000
035-12984-001-A-0204
Installer should pay particular attention to the words: NOTE, CAUTION and WARNING. Notes are intended to clarify or make the
installation easier. Cautions are given to prevent equipment damage. Warnings are given to alert installer that personal injury
and/or equipment damage may result if installation procedure is not handled properly.
MODELS B3CH 048 AND 060
(WORLD 50 HZ)
CAUTION
T H E E N C LO SE D IN S TA LLA TIO N IN S TR U C TIO N S A N D A N Y A P PLIC A B LE
LO C AL, ST AT E, A N D N AT IO N A L C O D E S IN C LU D IN G , B U T N O T LIM IT ED
TO , BU ILD IN G , ELE C TR IC A L, AN D M E C H AN IC A L C O D E S .
T H IS P R O D U C T M U S T B E IN S T A L L E D IN S T R IC T C O M P LIA N C E W IT H
WARNING
O P E R A T IO N O F T H E P R O D U C T C O U L D C A U S E P E R S O N A L IN J U R Y
O R P R O P E R T Y D A M A G E .
IN C O R R E C T IN S TA LLAT IO N M AY C R E A TE A C O N D IT IO N W H E R E TH E
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
035-12984-001-A-0204 2 Unitary Products Group General................................................................................1Inspection ............................................................................1Reference .......................................................................
LIMITATIONS These units must be installed in accordance with national andlocal or municiple safety codes: Refer to Table 1 for UnitApplication Data. If components are to be added to a unit to meet local codes, they are to be installed at the dealer's and / or the customer's expense. LOCATION Use the...
035-12984-001-A-0204 Unitary Products Group 5 FIG. 3 - TYPICAL FIELD WIRING CONTROL WIRING POWER WIRING NOMINAL HEATER SIZE KW VOLTAGE UNIT MODEL SIZE, NOMINAL TONS 4 5 MINIMUM SUPPLY AIR CFM 7 10152030 380/415-3+N-50 1,3001,3001,3001,300 – 1,6001,6001,6001,6001,600 TABLE 2 - AIR FLOW LIMITATIONS TO...
