Worx WG307E - Manual - manualsarea.com

Page 2 - GENERAL POWER TOOL

2 WG307E WG308E Limbing and Trimming Electric Chain Saw GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future r...

Page 3 - ADDITIONAL SAFETY

3 WG307E WG308E Limbing and Trimming Electric Chain Saw dust collection can reduce dust-related hazards. 4) PoWeR tool USe AND cARe a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was de...

Page 5 - SYMBOLS

5 WG307E WG308E Limbing and Trimming Electric Chain Saw Read the manual Warning Wear eye protection Wear ear protection Wear dust mask Do not expose to rain Remove plug from the mains immediately if the cable is damaged or cut. RCM approval mark Warning of danger from overhead electric-power lines S...

Page 8 - TECHNICAL DATA

8 WG307E WG308E Limbing and Trimming Electric Chain Saw TECHNICAL DATA Voltage 220-240V~50/60Hz Rated power 600W No load speed 3000/min Guide bar length 150mm Oil tank capacity 30ml Chain pitch 6.4mm Chain gauge 1.3mm Chain speed 5.5m/s Number of chain links 42 Weight WG307E 3.7kg (without pole) WG3...

Page 9 - INTENDED USE

9 WG307E WG308E Limbing and Trimming Electric Chain Saw INTENDED USE This JawSaw has been designed for pruning branches and cutting small logs up to 100mm in diameter, not for cutting metals (See Fig. A). ADJUSTMENT AND ASSEMBLY WARNING: Before touching the chain or making any other adjustments, mak...

Page 12 - LUBRICATION

12 WG307E WG308E Limbing and Trimming Electric Chain Saw 10.Check if all parts are seated properly (See Fig J).11.Refit and tighten the chain tensioner bolt. Note the cam (e) of the tensioner will engage the projecting tab (f) of the bar mounting plate and push the bar outward to tension the chain, ...

Page 13 - OPERATION

13 WG307E WG308E Limbing and Trimming Electric Chain Saw OPERATION PRePARe yoUR JAWSAW foR USe WARNING: Read and understand all instructions. failure to follow all instructions listed may result in electric shock, fire and/or serious personal injury. WARNING: Sharp moving blade. to prevent accidenta...

Page 17 - ASSEMBLING THE EXTENSION

17 WG307E WG308E Limbing and Trimming Electric Chain Saw ASSEMBLING THE EXTENSION POLE (ONLY FOR MODEL WG308E) WARNING: Before attaching the extension pole (20), make sure that the tool is switched off and unplugged. 1. Turn the release lever to allow the handle clamp to spring open (See Fig. Z1).2....

Page 19 - SAW MAINTENANCE AND; MAINTENANCE AND STORAGE OF

19 WG307E WG308E Limbing and Trimming Electric Chain Saw 6. One hand should firmly grip the push handle of the extension pole. The other hand should hold the metal portion of the pole or the sliding handle on the pole (See Fig. AC).7. Complete the cut as described in “Trimming Branches”.8. At the co...

Page 22 - TROUBLESHOOTING

22 WG307E WG308E Limbing and Trimming Electric Chain Saw TROUBLESHOOTING If your saw does not operate correctly check the following: PRoBleMS PoSSIBle cAUSeS PoSSIBle SolUtIoN • Tool will not start. • Fuse blown or breaker tripped.• Extension cord not plugged in. • Check fuse or breaker.• Check to m...

Worx WG307E - Manual

Table of Contents:

Summary

Other Worx Models