Page 2 - Table of Contents
Table of Contents 2 Warnings _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Kit Contents _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ...
Page 3 - IMPORTANT–; Please Read and Follow!; DANGER
IMPORTANT– Please Read and Follow! 3 Fire/explosion hazard. IF THE INFORMATION INTHIS MANUAL IS NOTFOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULTCAUSING PROPERTY DAMAGE,PERSONAL INJURY, OR DEATH. • DO NOT store or use gasoline or other flammable vapors and liquids in thevicinity of this or any oth...
Page 4 - LP Orifice Conversion Kit Contents
4 LP Orifice Conversion Kit Contents VGICVGRCVGRTVGCCVGSCDCCGDSCGDGRT VGR5VDR5VRT5 Burner Type Size Quantity Infrared Broiler 56 (2) Sealed Type 1 1.1 (8) Sealed Type 2 1.07 (8) Designer Surface Burner 57 (1) Designer Surface Burner 61 (1) Designer Surface Burner 63 (1) Designer Surface Burner 65 (1...
Page 5 - Regulator Conversion; Flip Cap; CAUTION
5 Regulator Conversion Flip Cap Hex Nut Cap Before proceeding with conversion, turn off gas supply and disconnect power to unit. • Sealed Surface Burner Models Identify regulator type from rear of range/rangetop located underneath main top assembly. • Open Surface Burner Models Identify regulator ty...
Page 6 - Infrared Broiler Conversion; Preparing for Top Surface Conversion
6 Infrared Broiler Conversion IMPORTANT: The infrared broiler orifice must be changed from rear of range before unit is installed. Locate bag labeled IR Broiler Orifice. Remove nut securing 90 degree fitting and broiler tubing to rear of range. Remove Orifice from 90 degree fitting and replace with ...
Page 8 - WARNING
8 Locate bag labeled Sealed Burner Orifice Type 2. NOTE: If the burner is a PowerPlus™ Burner (check control panel), use orifice kit 011915-000 to convertthis burner only. Remove the screws (Item #1) and set burner base aside (Item #2).IMPORTANT: Burner bases must be handled carefully to prevent ign...
Page 10 - Orifice Locations
10 Orifice Locations (#61) (#63) (#61) (#67) (#57) (#65) (#65) (#57) (#67) DGRT301 DGRT361 (#60) (#67) (#58) (#70) DCCG130 DSCD130
Page 11 - Open Burner Type 3
11 Open Burner Type 3 Surface Burner Conversion Locate bag labeled Open Burner Orifice Type 3.Remove screws securing open surface burner to burner box and remove open surface burner.NOTE: Igniter wire must be disconnected to remove burner.Loosen air shutter screw and adjust opening to 7/16” and tigh...
Page 12 - Griddle Conversion; U-Shape Burner with Spark Ignition
12 Griddle Conversion (for models equipped with griddle) U-Shape Burner with Spark Ignition Locate bag labeled Griddle Orifice.Remove screws securing griddle venturi plate to griddle box and remove griddle venturi plate.Remove screws securing griddle burner to burner box.Loosen air shutter screw and...
Page 13 - Straight Tube Burner with Spark Ignition
13 Griddle Conversion (for models equipped with griddle) Straight Tube Burner with Spark Ignition Locate bag labeled Griddle Orifice.Remove screws securing griddle venturi plate to griddle box and remove griddle venturi plate.Remove screws securing griddle burner to burner box.Loosen air shutter scr...
Page 14 - Straight Tube Burner with Glow Bar Ignition
14 Straight Tube Burner with Glow Bar Ignition Remove screws securing glow bar igniter to burner box and place glow bar igniter aside.Remove screws securing metal plate to burner box located underneath griddle burner and removemetal plate.Remove screws securing griddle burner to unit and remove grid...
Page 15 - Grill Conversion
15 Grill Conversion (for models equipped with grill) Lift flavor grids from unit.Lift flavor grid support from unit.Remove screws securing rear bracket to burner box.Remove screws securing flame shield to burner box.Lift out left and right side burner box liners.Remove screws securing burner to burn...
Page 16 - Wok Conversion; Overhead
16 Wok Conversion (for models equipped with wok) Remove center trivet and/or grates, center ring and grate support.Lift and remove burner from unit.Loosen air shutter screw and adjust opening on burner to 5/8” and tighten air shutter screw.Remove orifice by turning counterclockwise and replace with ...
Page 17 - Bake Conversion; “L” Shaped
17 Bake Conversion “L” Shaped Remove oven racks and rack supports.Remove oven bottom by sliding toward rear of range, then lift upward.Remove screws securing toe grille to unit.Remove screws securing burner support bracket to frame of unit and remove burner supportbracket.Slide bake burner to the le...
Page 18 - “U” Shaped
18 Bake Conversion “U” Shaped Remove oven racks and rack supports.Remove oven bottom.Remove screws securing bake igniter to bake burner.Remove screws securing bake burner shield to oven burner box.Remove screws securing bake burner to oven burner box.Loosen air shutter screw and adjust opening on bu...
Page 19 - Rating Label Locations
19 Rating Label Locations When LP/Propane conversion is complete, complete the enclosed conversion label and place it nextto the rating label. The rating label locations can be found as follows: Professional Open Burner Range & Rangetop - On the interior left side of the burner box. To accessthi...
