Page 3 - death; serious injury
iii Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not at...
Page 4 - Injury; damage; Precautions
iv If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorised TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause fire...
Page 5 - TABLE OF CONTENTS; GLOSSARIES
ENGLISH VERSION TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW .......................................................................................................... E1-1 1.1 Introduction ...................................................................................................................
Page 6 - OVERVIEW; Check for damage or; Ribbon Spindle
1. PRODUCT OVERVIEW ENGLISH VERSION 1. 1 Accessories 1. PRODUCT OVERVIEW 1.1 Introduction Thank you for choosing the B-SV4T series barcode printer. This Owner’s Manual contains valuable information from general set-up to confirming the printer's operation using test prints. You should read it carefu...
Page 7 - When purchasing the power cord; Power Cord Instruction
1. PRODUCT OVERVIEW ENGLISH VERSION 1.1 Introduction • When purchasing the power cord Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your Authorised TOSHIBA TEC representative. (As of June 2003) Country Agency Certificati...
Page 9 - Lamp
1. PRODUCT OVERVIEW ENGLISH VERSION 1.5 Appearance E1- 4 1.5.4 Interior 1.5.5 Button and Indicator Lamp The FEED/PAUSE Button and the Indicator Lamp have the following functions: As the FEED button • Pressing this button when the printer is in online state causes a media feed. • Pressing this button...
Page 11 - Procedure before; Power Switch
2. PRINTER SETUP ENGLISH VERSION 2.2 Procedure before Operation 2.2 Procedure before Operation 2.3 Turning the Printer ON/OFF 2.3.1 Turning ON the Printer This section describes the outline of the printer setup. 1. Unpack the accessories and printer from the box. 2. Refer to Safety Precautions in th...
Page 12 - Printer; Cables to the Printer
2. PRINTER SETUP ENGLISH VERSION 2.4 Connecting the Cables to the Printer E2- 3 2.3.2 Turning OFF the Printer 2.4 Connecting the Cables to the Printer 1. Before turning off the printer power switch verify that the Indicator Lamp is illuminated in green, not flashing. 2. To turn OFF the printer power...
Page 13 - Power Adapter and; Make sure that the printer power switch is in the OFF (O) position.; Since the power cord is not
2. PRINTER SETUP ENGLISH VERSION 2.5 Connecting the Power Adapter and the Power Cord E2- 4 2.5 Connecting the Power Adapter and the Power Cord 1. Make sure that the printer power switch is in the OFF (O) position. 2 . Insert the Power Cord into the inlet of the Power Adapter. 3. Insert the Power Ada...
Page 14 - Loading the Media; When the outer roll diameter
2. PRINTER SETUP ENGLISH VERSION 2.6 Loading the Media E2- 5 2.6 Loading the Media This section describes in detail how to load the media. 1. Turn OFF the printer and open the Top Cover. 2. Take out the Media Holder Ass’y from the printer. 3. Remove one of the Media Holders from the Media Shaft. 4. ...
Page 15 - The Feed Gap Sensor can be
2. PRINTER SETUP ENGLISH VERSION 2.6 Loading the Media E2- 6 2.6 Loading the Media (Cont.) 8. Feed the media between the Media Guides. 9. Pull the media until it extends past the Media Outlet. 10. Adjust the Media Guide position to the media width. 11. Make sure that the media path through the print...
Page 16 - Loading the Media; How to set the media; Strip block; close the; Media Outlet
2. PRINTER SETUP ENGLISH VERSION 2.6 Loading the Media 2.6 Loading the Media (Cont.) Strip mode (Option): When issued in the strip mode, labels are automatically removed from the backing paper each time a label is printed. • How to set the media When issuing labels in the strip mode, set the label i...
Page 17 - Rear Media Guides
2. PRINTER SETUP ENGLISH VERSION 2.6 Loading the Media 2.6 Loading the Media (Cont.) When a media roll has an outside diameter exceeding 127 mm (5 ” ) or an inner core diameter of 38.1 mm (1.5 ” ), the optional External Media Roll Hanger will be required. 1. Fit the protrusions on the bottom of the ...
Page 18 - Loading the Ribbon; ribbon
2. PRINTER SETUP ENGLISH VERSION 2.7 Loading the Ribbon 2.7 Loading the Ribbon The printer automatically detects if a ribbon is installed after power on and will switch to thermal transfer or direct thermal printing mode. If the printer does not detect a ribbon (direct thermal mode), the motor that ...
Page 19 - Calibration; NOTE; green; Orange; Dump Mode
2. PRINTER SETUP ENGLISH VERSION 2. 8 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities 2.8 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities This utility is used to calibrate the sensitivity of the Feed Gap/Black Mark Sensor. It is necessary to set the media sensor...
Page 20 - Print test label sample; TOTAL FEED
2. PRINTER SETUP ENGLISH VERSION 2. 8 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities 2.8.2 Self Print Test and Dump Mode (Cont.) Print test label sample PRINTER INFO.PROGRAM VERSION VX.XX XXXX TONE ADJUST +XX FEED ADJUST +XX.Xmm CUT POSITION ADJUST +XX.Xmm BACKFEED ADJUST +XX.Xmm...
Page 21 - Please purchase the Print Head
3. MAINTENANCE ENGLISH VERSION 3.1 Cleaning E3- 1 3. MAINTENANCE 3.1 Cleaning 3.1.1 Print Head This chapter describes how to perform routine maintenance. To ensure the continuous high quality operation of your printer, you should perform a regular maintenance routine. For high throughput it should b...
Page 22 - Wipe the Platen with a soft cloth moistened with alcohol.
3. MAINTENANCE ENGLISH VERSION 3.1 Cleaning E3- 2 3.1.2 Platen/Sensors 3.1.3 Cover 1. Wipe the Platen with a soft cloth moistened with alcohol. 2. Remove dust or paper particles from the Media Sensor and Cover Open Sensor using an air blower. Wipe the Cover with a dry soft cloth. Wipe off dirt with ...
Page 23 - Media
3. MAINTENANCE ENGLISH VERSION 3.2 Care/Handling of the Media E3- 3 3.2 Care/Handling of the Media • Do not store media for longer than the manufacturer’s recommended shelf life • Store media rolls on the flat end. Do not store them on the curved sides as this might flatten that side causing erratic...
Page 24 - Troubleshooting Guide; Problems; Removing Jammed Media; representative for assistance.; Do not use any tool that may damage the print head.
4. TROUBLESHOOTING ENGLISH VERSION 4.1 Troubleshooting Guide E4- 1 4. TROUBLESHOOTING This chapter lists the error messages, possible problems, and their solutions. 4.1 Troubleshooting Guide Problems Solutions The Online Indicator Lamp (green) is not illuminated. 1. Check that the Power Cord is prop...
Page 25 - APPENDIX 1 SPECIFICATIONS; Item; Data Matrix; QR Code is a trademark of DENSO CORPORATION.
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION A1.1 Printer EA1- 1 APPENDIX 1 SPECIFICATIONS Appendix 1 describes the printer specifications and supplies for use on the B-SV4T printer. A1.1 Printer The following are the printer specifications. Item Specifications AC100 to 240V, 50/60 Hz 100 to 120V: 2.1A...
Page 26 - Option Name; Feed Direction; Tag paper; Label
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION A1.2 Options EA1- 2 A1.2 Options Option Name Type Description Keyboard display unit KB-75-QM This module is an external intelligent keyboard display unit. Cutter module B-SV204-QM B-SV404-QM A cutter unit that makes stub cuts A cutter unit that makes normal ...
Page 27 - A1.3.2 Detection Area of the Transmissive Sensor; optional External Media Roll Hanger is required.
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION A1.3 Media EA1- 3 A1.3.1 Media Type (Cont.) Unit: mm (inch) Issue mode Item Batch mode Strip mode Cut mode Width including backing paper 25.4 to 112 (1.0 to 4.4) Media width Min. 17 (0.7) Media pitch 10 to 1000(0.39 to 39.3) 25.4 to 1000 (1.0 to 39.3) Media ...
Page 29 - APPENDIX 2 INTERFACE; Interface Cables; Keep as short as possible.; RS-232C Cable description
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION APPENDIX2 INTERFACE EA2-1 Function 9 pin 25 pin RXD 2 3 TXD 3 2 DTR 4 20 GND 5 7 DSR 6 6 RTS 7 4 C TS 8 5 APPENDIX 2 INTERFACE Interface Cables To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements:...
