Page 2 - - Consult the dealer or an experienced radio/TV technician for help.; Waste Recycling information for users:; Following information is only for EU-member states:
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. VORSICHT: • Schallemission: unter 70dB (A) nach DIN 45635 (oder ISO 7779) • Die für das Gerät Vorgesehene Steckdose muß in der Nähe des Gerätes und leicht zugänglich ...
Page 3 - TOSHIBA Barcode Printer; Owner’s Manual
TOSHIBA Barcode Printer B-SV4D SERIES Owner’s Manual
Page 4 - Safety Summary; This indicates that there is the risk of; death; or; serious injury; if the; WARNING
Safety Summary ENGLISH VERSION EO1-33061 ( ) i Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understo...
Page 5 - This indicates that there is the risk of personal; Injury; damage; to; Precautions; CAUTION
Safety Summary ENGLISH VERSION EO1-33061 ( ) ii If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorised TOSHIBA TEC representative for assistance. Continued use of...
Page 6 - TABLE OF CONTENTS; GLOSSARIES
ENGLISH VERSION EO1-33061 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW .......................................................................................................... E1-1 1.1 Introduction .........................................................................................................
Page 7 - OVERVIEW; This printer has the following features:
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33061 1.1 Introduction E1- 1 1. PRODUCT OVERVIEW 1.1 Introduction 1.2 Features 1.3 Unpacking 1.4 Accessories Thank you for choosing the TOSHIBA B-SV4D series barcode printer. This Owner’s Manual contains valuable information from general set-up to confirming t...
Page 8 - When purchasing the power cord
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33061 1.4 Accessories E1- 2 When purchasing the power cord Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your Authorised TOSHIBA TEC representative. (As of September 2004) Country ...
Page 10 - Lamp
1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33061 1.5 Appearance E1- 4 1.5.4 Interior 1.5.5 Button and Indicator Lamp The FEED/PAUSE Button and the Indicator Lamp have the following functions: As the FEED button • Pressing this button when the printer is in online state causes a media feed. • Pressing t...
Page 11 - SETUP; Store the media in accordance with the specifications.
2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.1 Precautions E2- 1 2. PRINTER SETUP 2.1 Precautions This section outlines the steps necessary to setup your printer prior to its operation. The section includes precautions, connecting cables, assembling accessories, loading media, and performing a test ...
Page 12 - Procedure before; Power Switch
2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.2 Procedure before Operation E2- 2 2.2 Procedure before Operation 2.3 Turning the Printer ON/OFF 2.3.1 Turning ON the Printer This section describes the outline of the printer setup. 1. Unpack the accessories and printer from the box. 2. Refer to Safety P...
Page 13 - Printer; Cables to the Printer; Do not turn off the printer
2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.4 Connecting the Cables to the Printer E2- 3 2.3.2 Turning OFF the Printer 2.4 Connecting the Cables to the Printer 1. Before turning off the printer power switch verify that the Indicator Lamp is illuminated in green, not flashing. 2. To turn OFF the pri...
Page 14 - Make sure that the printer power switch is in the OFF (O) position.; Power Adapter; Since the power cord is not
2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.5 Connecting the Power Adapter and the Power Cord E2- 4 2.5 Connecting the Power Adapter and the Power Cord 1. Make sure that the printer power switch is in the OFF (O) position. 2 . Insert the Power Cord into the inlet of the Power Adapter. 3. Insert the...
Page 15 - This section describes in detail how to load the media.; Slot
2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.6 Loading the Media E2- 5 2.6 Loading the Media This section describes in detail how to load the media. 1. Turn OFF the printer and open the Top Cover. 2. When the inner core diameter of the media roll is 25.4 mm (1”), remove the Media Holder Spacers from...
Page 16 - Loading the Media; The Feed Gap Sensor can be; Media Sensor
2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.6 Loading the Media E2- 6 2.6 Loading the Media (Cont.) 6. Feed the media between the Media Guides. 7. Pull the media until it extends past the Media Outlet. 8. Adjust the Media Guide position to the media width by rotating the Media Guide Adjustment Knob...
Page 17 - How to set the media; Open the Strip Block by the tabs on both sides.; Be sure to cut the backing; When attaching or removing
2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.6 Loading the Media E2- 7 Strip Feed Roller 2.6 Loading the Media (Cont.) Strip mode (Option): When issued in the strip mode, labels are automatically removed from the backing paper each time a label is printed. • How to set the media When issuing labels ...
Page 19 - Orange
2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.7 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities E2- 9 2.7 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities 2.7.1 Media Sensor Calibration 2.7.2 Self Print Test and Dump Mode This utility is used to calibrate the sens...
Page 20 - Print test label sample; TOTAL FEED
2. PRINTER SETUP ENGLISH VERSION EO1-33061 2.7 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities E2-10 2.7.2 Self Print Test and Dump Mode (Cont.) Print test label sample The test print contents should be changed by the following commands and parameters: PROGRAM VERSION: VX.XX XXXX ...
Page 22 - Print Head Element (positioned at the print head edge)
3. MAINTENANCE ENGLISH VERSION EO1-33061 3.1 Cleaning E3- 1 3. MAINTENANCE 3.1 Cleaning 3.1.1 Print Head This chapter describes how to perform routine maintenance. To ensure the continuous high quality operation of your printer, you should perform a regular maintenance routine. For high throughput i...
Page 23 - Platen
3. MAINTENANCE ENGLISH VERSION EO1-33061 3.1 Cleaning E3- 2 3.1.2 Platen/Sensors 3.1.3 Cover 1. Wipe the Platen with a soft cloth moistened with alcohol. 2. Remove dust or paper particles from the Media Sensor and Cover Open Sensor using an air blower. Wipe the Cover with a dry soft cloth. Wipe off ...
Page 24 - Media
3. MAINTENANCE ENGLISH VERSION EO1-33061 3.2 Care/Handling of the Media E3- 3 3.2 Care/Handling of the Media • Do not store media for longer than the manufacturer’s recommended shelf life • Store media rolls on the flat end. Do not store them on the curved sides as this might flatten that side causi...
Page 25 - Troubleshooting Guide; Problems Solutions; Removing Jammed Media; Do not use any tool that may damage the print head.
4. TROUBLESHOOTING ENGLISH VERSION EO1-33061 4.1 Troubleshooting Guide E4- 1 4. TROUBLESHOOTING This chapter lists the error messages, possible problems, and their solutions. 4.1 Troubleshooting Guide Problems Solutions The Online Indicator Lamp (green) is not illuminated. 1. Check that the Power Co...
Page 26 - APPENDIX 1 SPECIFICATIONS; The following are the printer specifications.; Item Specifications; Optional interface; QR Code is a trademark of DENSO CORPORATION.
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33061 A1.1 Printer EA1- 1 APPENDIX 1 SPECIFICATIONS Appendix 1 describes the printer specifications and supplies for use on the B-SV4D printer. A1.1 Printer The following are the printer specifications. Item Specifications AC100 to 240V, 50/60 Hz 100 to ...
Page 27 - Option Name; Feed Direction; Tag paper; Label
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33061 A1.2 Options EA1- 2 A1.2 Options Option Name Type Description Keyboard display unit KB-75-QM-R This module is an external intelligent keyboard display unit. Cutter module B-SV204-QM-R B-SV404-QM-R A cutter unit that makes stub cuts. A cutter unit t...
Page 28 - A1.3.2 Detection Area of the Transmissive Sensor; optional External Media Roll Hanger is required.
APPENDIX 1 SPECIFICATIONS ENGLISH VERSION EO1-33061 A1.3 Media EA1- 3 A1.3.1 Media Type (Cont.) Unit: mm (inch) Issue mode Item Batch mode Strip mode Cut mode c Width including backing paper 25.4 to 112 (1.0 to 4.4) d Media width Min. 17 (0.7) e Media pitch 10 to 609 (0.39 to 24.0) 15 to 609 (0.59 t...
Page 30 - APPENDIX 2 INTERFACE; Interface Cables; Keep as short as possible.; RS-232C Cable description; Connector to the Host Computer
APPENDIX 2 INTERFACE ENGLISH VERSION EO1-33061 APPENDIX 2 INTERFACE EA2- 1 APPENDIX 2 INTERFACE Interface Cables To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements: • Fully shielded and fitted with metal or metallized connector housings....
Page 32 - INDEX
INDEX ENGLISH VERSION EO1-33061 INDEX INDEX B Backing paper A1-3 Bar code A1-1 Batch mode 2-6 Black mark A1-2 Black mark length A1-3 Black mark sensor 2-6, 2-9 C Centronics 1-4, 2-2, 2-3, A1-1 Cover open sensor 1-4, 3-2 Cut mode 2-7 Cutter module A1-2 D Dimensions 1-3, A1-1 E Effective print range A...
