Page 2 - Warning Labels; Safety Precautions; CAUTION; WARNING
Table of Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Grounding Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Gasoline Engine Safety . . . . ...
Page 4 - Grounding Instructions; Gasoline Engine Safety
Grounding Instructions Electric models must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. Th...
Page 5 - Specifications; Gas Units
© Titan Tool Inc. All rights reserved. 5 Specifications Gas Units Delivery (GPM) 1.2 (LPM) 4.5 Cycles per gallon 87 Cycles per liter 23 Cycles per minute (maximum) 104 Maximum Tip Size - 1 Gun .034" Maximum Tip Size - 2 Guns .025" Maximum Tip Size - 3 Guns .019" Pressure Range (psi) 400 ...
Page 6 - Operating Components
6 © Titan Tool Inc. All rights reserved. Bleed Line Siphon Hose Hydraulic Filter Muffler Hydraulic Fluid Fill and Dipstick Hydraulic Bypass Valve Choke Engine ON/OFF Switch Hydraulic Reservoir Grounding Lug Hydraulic Return Hose Hydraulic Pressure Hose Siphon Hose Fluid Pump Pressure Adjustment Knob...
Page 7 - Setup; Fueling; Fuel Specifications
Setup Read, understand, and follow all warnings before starting or operating this sprayer. 1. Connecting the Hoses: The siphon hose and the bleed line hose have factory installed 37)( tape on the male end of the hoses. Tighten the syphon hose and bleed line wrench tight. 2. One Gun Operation - Attac...
Page 8 - Gasolines Containing Alcohol; Startup
Gasolines Containing Alcohol If you decide to use a gasoline containing alcohol (gasohol), be sure its octane rating is at least as high as that recommended by the engine manufacturer. There are two types of "gasohol": one containing ethanol, and the other containing methanol. Do not use gas...
Page 9 - Cleanup; Pressure Relief Procedure; Color Change/Clean Out
Cleanup Special cleanup instructions for use with flammable solvents: • Always flush spray gun preferably outside and at least one hose length from spray pump. • If collecting flushed solvents in a one gallon metal container, place it into an empty five gallon metal container, then flush solvents. •...
Page 10 - Maintenance; Hydraulic System; General Fluid Pump Maintenance; Basic Engine Maintenance; Engine Operation and Service
Maintenance Hydraulic System Use of Speeflo's Coolflo™ Hydraulic Fluid is mandatory in the PowrTwin hydraulic system. Do not use any other hydraulic fluid. Use of any other hydraulic fluid may seriously damage hydraulic system and will void warranty. 1. Check the hydraulic fluid daily. It should rea...
Page 11 - Troubleshooting; Airless Gun; Fluid Section; Problem
© Titan Tool Inc. All rights reserved. 11 Troubleshooting Airless Gun Problem Spitting gun Gun will not shut off Gun does not spray Fluid Section Problem Pump delivers on upstroke only or goes up slowly and down fast (commonly called downstroke dive) Pump delivers on down stroke only or goes up fast...
Page 12 - Hydraulic Motors; Cause
Hydraulic Motors Problem Oil motor stalls at bottom (no unusual heat problems) Oil motor stalls at top (no unusual heat problems) Low pressure (okay on down stroke, sluggish on up.stroke — high heat) NOTE: Engine labors on upstroke, idles back at stall on the down stroke. Low pressure (both strokes ...
Page 13 - Spray Patterns
© Titan Tool Inc. All rights reserved. 13 Troubleshooting Spray Patterns Problem Tails Hour glass Distorted Pattern expanding and contracting (surge) Round pattern Cause 1. Inadequate fluid delivery 1. Inadequate fluid delivery 1. Plugged or worn nozzle tip 1. Suction leak 2. Pulsating fluid deliver...
Page 14 - Sécurité; AVERTISSEMENT; ATTENTION
Sécurité Le présent manuel comprend des renseignements devant être lus attentivement avant toute utilisation de l'appareil. Lorsque l'un des symboles suivants apparaît, il est recommandé d'être particulièrement attentif et de tenir compte des mesures de sécurité indiquées. Ce symbole indique un dang...
Page 15 - Instructions de mise à la terre; Sécurité du moteur à essence
DANGER: GÉNÉRALITÉS - Peut causer des dommages matériels ou corporels sérieux. MESURES PRÉVENTIVES: • Avant d'utiliser tout équipement, lire attentivement toutes les instructions et les consignes de sécurité • Toujours débrancher le moteur de l’alimentation électrique avant d’effectuer des travaux s...
Page 16 - Seguridad; ADVERTENCIA; PRECAUCION
Seguridad Este manual contiene información que debe leer y comprender antes de usar el equipo. Cuando se encuentre con uno de los siguientes símbolos, asegúrese de observar sus indicaciones de seguridad. Este símbolo indica la existencia de un peligro potencial que puede causar lesiones graves o la ...
Page 17 - Instrucciones para conectar a tierra; Seguridad con los motores de gasolina
• Observe todos los códigos locales, estatales y nacionales apropiados que rigen las medidas de ventilación, prevención de incendios y operación. • Los Estándares de Seguridad del Gobierno de los Estados Unidos se han adoptado bajo el Acta de Seguridad y Salud Ocupacionales (OSHA por sus siglas en i...
Page 18 - Parts Lists, Drawings, and Service Instructions; Major Components
18 © Titan Tool Inc. All rights reserved. Honda Item Part # Description 335-580 1 335-555 Cart assembly ........................................................1 2 920-559 Filter assembly, outlet manifold .............................1 3 235-107 Motor/pump assembly .....................................
Page 20 - DC — Electric Convertokits
20 © Titan Tool Inc. All rights reserved. DC — Electric Convertokits 506-217 506-204 506-214 115V CSA, 115V 220V Item Part # Description Qty. Qty. Qty. 1 506-259 Cover ......................................................................1 ................1 ...............1 2 860-501 Nut stop .........
Page 21 - Electric Convertokit Service Instructions
© Titan Tool Inc. All rights reserved. 21 Electric Convertokit Service Instructions Before servicing the electric motor, follow the Pressure Relief Procedure in the Cleanup section of this manual. Once you have completed this procedure, unplug the power supply cord. Failure to reduce pressure can re...
Page 22 - Cart Assembly
22 © Titan Tool Inc. All rights reserved. Cart Assembly Item Part # Description Quantity 1 590-502 Handle ..............................................1 2 449-051 Motor/pump bracket ..........................1 3 335-562 Axle ...................................................1 4 335-563 Spacer, lon...
Page 23 - Torque and Sealant Guide
© Titan Tool Inc. All rights reserved. 23 Hydraulic System 4 5 6 7 8 10 13 14 15 16 18 1920 26 25 22 24 212223 17 12 11 9 3 2 1 30 35 36 37 39 44 43 45 21 38 40 4142 43 3637 34 31 32 33 27 28 29 Item Part # Description Quantity 1 420-250 Tubing, 37)( ...........................................1 2 44...
Page 24 - Hydraulic Motor; Hydraulic Motor Service Instructions
24 © Titan Tool Inc. All rights reserved. Hydraulic Motor Hydraulic Motor Service Instructions Disassembly 1. Disconnect the high pressure hose line from the elbow (31, in Hydraulic System parts list) on the back of the rotary pump. 2. Remove the two mounting screws (22 and 23, in Cart Assembly part...
Page 26 - Connecting Pin Arrangement; Fluid Pump; Fluid Pump Service Instructions
26 © Titan Tool Inc. All rights reserved. 7. With motor/pump block (25) still in vise, install lower seal (24) by pushing it towards its groove with a properly sized blunt rod. Then complete installation with the fingers. No tool is necessary. Do not twist the seal. 8. Pre-lubricate the piston and v...
Page 28 - Inlet Accessories; Siphon Hose Assembly
28 © Titan Tool Inc. All rights reserved. Inlet Accessories Bleed Line Assembly with Valve (P/N 840-211) Item Part # Description Quantity 1 944-620 Bleed valve...............................................1 2 103-117 Tube .........................................................1 3 539-078 Hose ass...
Page 29 - Outlet Accessories; 20 Outlet Manifold Filter Assembly
© Titan Tool Inc. All rights reserved. 29 Outlet Accessories 920 Outlet Manifold Filter Assembly Item Part # Description Quantity 1 920-917 Filter cap assembly ..................................1 2 920-103 Ball ...........................................................1 3 920-004 Filter element, 50...
Page 31 - SAE O-Ring Fitting Installation; Accessories and Service Kits; Airless Tip Selection
© Titan Tool Inc. All rights reserved. 31 SAE O-Ring Fitting Installation Steps 1 & 2: Step 3: Step 4: Step 5: Cautions: Lubricate Lubricate Tighten nut Recess gap No gap Align Hold this part stationay Avoid screwing fitting in too far. Avoid leaving fitting too far out. Bent washer allows for o...
Page 32 - Limited Warranty; Patents
32 © Titan Tool Inc. All rights reserved. Limited Warranty Titan Tool Inc. warrants all equipment manufactured by it and bearing its brand names to be free from defects in material and workmanship at the time of sale by an authorized Speeflo distributor. Titan Tool Inc. will for a period of twelve m...
