Titan 110V Complete - Manuals

Titan 110V Complete – Manual in PDF format online.

Manuals:

Manual

Manual Titan 110V Complete

Summary

Page 2 - CAUTION; WARNING

Table of Contents Safety Precautions ..................................................................2 Français ...............................................................................14Español................................................................................16 General Descrip...

Page 3 - Grounding Instructions

GAS ENGINE (WHERE APPLICABLE) Always place sprayer outside of structure in fresh air. Keep allsolvents away from the engine exhaust. Never fill fuel tankwith a running or hot engine. Hot surface can ignite spilledfuel. Always attach ground wire from sprayer unit to agrounded object, such as a metal ...

Page 4 - Setup; Preparing a New Sprayer; Preparing to Paint

General Description This piston pump is a precision power tool used for sprayingmany types of materials. Read and follow this instructionmanual carefully for proper operating instructions,maintenance, and safety information. Operation This equipment produces a fluid stream at extremely highpressure....

Page 5 - Painting; Pressure Relief Procedure

12. Unlock the gun by turning the gun trigger lock to the unlocked position. Ground the gun by holding it againstthe edge of the metal container whileflushing. Failure to do so may lead toa static electric discharge, which maycause a fire. 13. Trigger the gun into the metal waste container. 14. Slow...

Page 6 - Spraying; Spraying Technique; Practice

Spraying POSSIBLE INJECTION HAZARD. Do not spray without thetip guard in place. Never trigger the gun unless the tip isin either the spray or the unclog position. Always engagethe gun trigger lock before removing, replacing, orcleaning tip. Spraying Technique The following techniques, if followed, w...

Page 7 - Cleanup; Maintenance; General Repair and Service Notes

Cleanup Special cleanup instructions for use with flammablesolvents: • Always flush spray gun preferably outside and at least one hose length from spray pump. • If collecting flushed solvents in a one gallon metal container, place it into an empty five gallon container, thenflush solvents. • Area mu...

Page 8 - Replacing the Motor; Replacing the Motor Brushes; Replacing the Gears

Replacing the Motor 1. Unplug the unit.2. Loosen and remove the four rear cover screws. Remove the rear cover. 3. Remove the cover plate and the insulator plate on the pump housing by removing the corresponding fourscrews. 4. Disconnect the white motor wire from the white power cord wire and the bla...

Page 9 - Replacing the Switch Stem

Replacing the Motor Starter Before proceeding, follow the Pressure Relief Procedureoutlined previously in this manual. Additionally, follow allother warnings to reduce the risk of an injection injury,injury from moving parts or electric shock. Always unplugthe sprayer before servicing! 1. Remove the...

Page 10 - Servicing the Fluid Section; Servicing the Valves; Repacking the Fluid Section

Servicing the Fluid Section Use the following procedures to service the valves and repackthe fluid section. Perform the following steps beforeperforming any maintenance on the fluid section. 1. Loosen and remove the four front cover screws. Remove the front cover. 2. Stop the sprayer at the top of i...

Page 11 - Replacing the Transducer; Replacing the Filters; Pump Filter

18. Insert the elbow on the suction set into the bottom of the foot valve. Position the retaining clip into the foot valve tosecure the suction set assembly. 19. Thread the return hose into the pump block and tighten securely. 20. Place the front cover on the pump housing and secure in position usin...

Page 12 - Troubleshooting; Airless Pump

Solution 1. Check2. Increase3. Replace4. Replace5. Replace6. Replace 1. Check siphon tube o-ring and/or let paint circulate in prime position 2. Increase pressure 1. Check supply2. Clean3. Clean and replace4. Thin material 1. Tighten connections2. Tighten, check for leaks3. Service or clean4. Replac...

Page 13 - Spray Patterns; Problem

© Titan Tool Inc. All rights reserved. 13 Troubleshooting Spray Patterns Problem Tails Heavy centered pattern Distorted pattern Pattern expanding andcontracting (Surge) Cause 1. Inadequate fluid delivery2. Fluid not atomizing3. Insufficient velocity4. Material too cohesive5. Tip worn past pump capac...

Page 14 - Consignes de sécurité; AVERTISSEMENT; ATTENTION

14 © Titan Tool Inc. Tous droits réservés. Consignes de sécurité Le présent manuel comprend des renseignements devant êtrelus attentivement avant toute utilisation de l'appareil. Lorsquel'un des symboles suivants apparaît, il est recommandé d'êtreparticulièrement attentif et de tenir compte des mesu...

Page 15 - Instructions de mise à la terre

© Titan Tool Inc. Tous droits réservés. 15 MOTEUR À ESSENCE (DANS LES CAS OÙ CELA S’APPLIQUE) Toujours placer la pompe à l’extérieur de la structure à l’airfrais. Garder tous les solvants loin de l’échappement dumoteur. Ne jamais remplir le réservoir à carburant lorsque lemoteur est en marche ou lor...

Page 16 - Precauciones de seguridad; ADVERTENCIA; PRECAUCION

16 © Titan Tool Inc. Todos los derechos reservados. Precauciones de seguridad Este manual contiene información que debe leer y comprenderantes de usar el equipo. Cuando se encuentre con uno de lossiguientes símbolos, asegúrese de observar sus indicacionesde seguridad. Este símbolo indica la existenc...

Page 17 - Instrucciones para conectar a tierra

© Titan Tool Inc. Todos los derechos reservados. 17 PELIGRO: PELIGRO DE EXPLOSIÓN DEBIDO A MATERIALES INCOMPATIBLES - Podríacausar lesiones severas o daños en lapropiedad. PARA PREVENIR: • No utilice materiales que contengan blanqueador o cloro.• No use solventes con hidrocarburos halogenados, tales...

Page 18 - Parts List; Main Assembly

Page 20 - Gear Box Assembly

Page 21 - Electrical Schematics

© Titan Tool Inc. All rights reserved. 21 Item Part # Description Quantity 1 700-511 Thrust washer ..................................1 2 700-732 Pinion gear.......................................1 3 710-120 Crankshaft/gear assembly ...............1 4 700-680 Thrust washer ..............................

Page 22 - Pump Block Assembly

22 © Titan Tool Inc. All rights reserved. Pump Block Assembly 1 2 3 7 6 9 8 4 5 10 11 12 13 14 15 16 17 18 19 Item Part # Description Quantity 1 700-421 Filter housing ...................................1 2 500-200-03 Filter .................................................1 3 560-038 Seal ............

Page 23 - Fluid Section Assembly; Accessories; Airless Tip Selection

© Titan Tool Inc. All rights reserved. 23 Fluid Section Assembly Item Part # Description Quantity 1 704-120 Fluid section complete ..........................1 1A 704-085 Fluid section complete (includes filterand PRIME/SPRAY valve assembly) 2 704-090 Piston assembly (includes items 8–14) .....1 3 70...