Page 2 - English; Important Safety Information; Read all safety information before
English 2 © Titan Tool Inc. All rights reserved. Important Safety Information · Read all safety information before operating the equipment. SavE ThESE INSTRucTIONS. This symbol indicates a hazardous situation, which, if not not avoided could result in death or serious injury.To reduce the risks of f...
Page 3 - Grounding Instructions
© Titan Tool Inc. All rights reserved. 3 Important Safety Information · Read all safety information before operating the equipment. SavE ThESE INSTRucTIONS. haZaRD: EXPLOSION haZaRD DuE TO INcOMPaTIBLE MaTERIaLS Will cause property damage or severe injury. PREvENTION: • Do not use materials containi...
Page 4 - Table of contents; Specifications
4 © Titan Tool Inc. All rights reserved. Table of contents Safety Precautions ................................................................... 2 Grounding Instructions ........................................................ 3 Specifications ..........................................................
Page 5 - Introduction; admiralTM Series
© Titan Tool Inc. All rights reserved. 5 Introduction Congratulations on having selected the finest airless sprayer available in the world. This Admiral™ represents the latest in airless technology. Its ability to efficiently apply a wide range of coatings makes it an excellent buy. We thank you for...
Page 6 - Setup
6 © Titan Tool Inc. All rights reserved. Setup The flow from the spray tip is at very high pressure. contact with any body part may be dangerous. Do not place finger on gun outlet. Do not point the gun at any person.Read, understand, and follow all warnings before starting or operating this sprayer....
Page 7 - Startup
© Titan Tool Inc. All rights reserved. 7 Startup 1. Close the self relieving shutoff valve. The figure below shows the handle in the closed position. 2. Start the compressor. 3. Drain the Petcock by pushing it off center. 4. adjusting the air regulator: The air motor is designed for a maximum air in...
Page 8 - Operation; Pressure Relief Procedure; color change / clean Out; PTFE
8 © Titan Tool Inc. All rights reserved. Operation 1. Repeat above Startup procedure with paint material. Lock gun trigger and attach spray tip. See the Technical Data Sheet on the gun provided for installation and selection of the proper tip size. 2. Test spray pattern. Operate the pump at the lowe...
Page 9 - air Motor Maintenance; NOTE: An air line filter / moisture separator are standard; Fluid Pump Maintenance; Lubrisolv; IMPORTaNT: It is very important that the threads on the; hydraulic Motor and Paint Pump Service
© Titan Tool Inc. All rights reserved. 9 air Motor Maintenance Air motors require a normal maintenance and service inspection at 1500 hours service. Service procedure includes replacement of motor service kit, minor. It is suggested that one motor service kit, major (which includes the minor kit) be...
Page 10 - Troubleshooting - airless Spraying
10 © Titan Tool Inc. All rights reserved. Troubleshooting - airless Spraying condition Possible cause correction A. Poor spray pattern and / or tails at top and bottom of the spray pattern. Worn or incorrect tip and/or insufficient atomization.Hose size or length is too small or too long. Dirty filt...
Page 12 - admiralTM Series Portable Models
12 © Titan Tool Inc. All rights reserved. admiral™ Series Portable Models 1 3 3 7 7 2 5 6 4 2 8 8 1
Page 13 - aLL MODELS WITh hEavy DuTy caRT
© Titan Tool Inc. All rights reserved. 13 admiral™ Series Portable Models aLL MODELS WITh hEavy DuTy caRT 30:1 40:1 60:1 ITEM NO. PaRT NO. DEScRIPTION 830-451 941-421 941-441 860-451 860-461 1 850-245 850-557 142-104 245-556 Motor pump assembly Air motor Assembly set Fluid pump assembly 1 1a 850-185...
Page 14 - admiralTM Series Wall Mount and Drum Mount Models
14 © Titan Tool Inc. All rights reserved. admiral™ Series Wall Mount and Drum Mount Models 1 4 9 3 1 2 2 6 6 8 5
Page 17 - Disassembly Procedure; Description
© Titan Tool Inc. All rights reserved. 17 air Motor Service Procedure This Air Motor requires a normal mantenance inspection at 1500 hours of service on the non-circulating models and 800 hours of service on the circulating models. Service procedure includes replacement of the Motor Service Kit, Min...
Page 19 - Reassembly Procedure; Service Kits
© Titan Tool Inc. All rights reserved. 19 155-559 Fluid Pump Service Information IMPORTaNT: use of non-Titan manufactured service parts may void warranty. The 155 Series Pump should receive a routine servicing after approximately 1000 hours of use or earlier if there is excessive leakage from the to...
Page 21 - Full thread engagement is sufficient. The foot
© Titan Tool Inc. All rights reserved. 21 181-556 Fluid Pump Service Information IMPORTaNT: use of non-Titan manufactured service parts may void warranty. The 181 Series Pump should receive a routine servicing after approximately 1000 hours of use or earlier if there is excessive leakage from the to...
Page 23 - pump is to be used for heavy block filler or
© Titan Tool Inc. All rights reserved. 23 185-551 Fluid Pump Service Information IMPORTaNT: use of non-Titan manufactured service parts may void warranty. The 185 Series Pump should receive a routine servicing after approximately 1000 hours of use or earlier if there is excessive leakage from the to...
Page 27 - admiralTM heavy Duty cart; heavy Duty cart assembly; cart Dimensions
© Titan Tool Inc. All rights reserved. 27 admiral™ heavy Duty cart A G H E F C I J D B 1 3 7 8 9 10 11 4 2 3 5 6 Part No. 590-301 heavy Duty cart assembly ITEM NO. PaRT NO. DEScRIPTION QTy. 1 590-352 Handle 1 2 935-014 End cap 2 3 590-350 Frame 2 4 862-410 Nut, 3/8” - 16 10 5 862-001 Washer, 3/8” 14...
Page 28 - admiralTM Pump Mount Drum cover; ITEM
28 © Titan Tool Inc. All rights reserved. admiral™ Pump Mount Drum cover 1 2 3 4 5 8 6 11 7 910 55 Gal. Drum cover assembly, Part No. 219-600 ITEM NO. PaRT NO. DEScRIPTION QTy. 1 860-535 Screw, HH, 5/16 - 18 x 7/8” 4 2 862-452 Screw, HH, 3/8 - 16 x 1.5” 1 3 219-506 Knob, plastic 1 4 219-505 Plate, i...
Page 29 - admiralTM Pump Mounts
© Titan Tool Inc. All rights reserved. 29 admiral™ Pump Mounts Mounting kit for 2 stanchion pump Part # 219-100* Part # 219-200 ITEM NO. PaRT NO. DEScRIPTION QTy. QTy. 1 860-535 Screw 4 4 2 219-504 Adapter plate 1 1 3 860-003 Washer 4 4 4 860-502 Nut 4 4 5 191-444 Nipple, extension 1 * For use with ...
Page 30 - admiralTM Outlet accessories - 920 Outlet Manifold Filter assembly; Outlet Manifold Filter assembly
30 © Titan Tool Inc. All rights reserved. admiral™ Outlet accessories - 920 Outlet Manifold Filter assembly Outlet Manifold Filter assembly ITEM NO. PaRT NO. DEScRIPTION 5000 psi 5000 psi 6000 psi 920-554 920-556 920-605 1 920-917 Cap, filter (5000 psi) 1 1 1a 920-930 Cap, filter (6000 psi) 1 2 920-...
Page 31 - cleaning
© Titan Tool Inc. All rights reserved. 31 admiral™ 920 Outlet Manifold Filter assembly Service Instructions cleaning Clean filter regularly. Dirty or clogged filters can greatly reduce filtering ability and cause a number of system problems including poor spray patterns, clogged spray tips, etc. To ...
Page 32 - admiralTM Fluid accessories - Siphon hoses; Siphon hose assemblies
32 © Titan Tool Inc. All rights reserved. admiral™ Fluid accessories - Siphon hoses Siphon hose assemblies ITEM NO. PaRT NO. DEScRIPTION 103-806 103-807 103-808 103-810 1 103-625 Rock Catcher 1 1a 710-046 Filter screen 1 1 1b 103-665 Strainer, 30 mesh 1 2 103-585 Siphon tube, 1” x 36” 1 2a 103-595 S...
Page 33 - admiralTM Fluid accessories
© Titan Tool Inc. All rights reserved. 33 admiral™ Fluid accessories Outlet Tee assembly with Pressure Bleed valve Part # 840-205 ITEM NO. PaRT NO. DEScRIPTION QTy. 1 200-554 Adapter, swivel 1 2 817-003 Tee 1 3 945-600 Pressure bleed valve 1 4 103-106 Bleed line assembly 1 5 813-555 Nipple, hex 1 84...
Page 34 - admiralTM Outlet accessories; Service Instructions
34 © Titan Tool Inc. All rights reserved. admiral™ Outlet accessories 944-620 Bleed valve assembly ITEM NO. PaRT NO. DEScRIPTION QTy. 1 944-005 Knob 1 2 860-721 Nut, lock 1 3 944-023 Valve stem 1 4 944-020 Valve body 1 5 944-004 O-ring 1 6 944-026 Valve stem stop 1 7 569-170 Ball, T.C. 1 8 945-003 G...
Page 35 - admiralTM Outlet accessories - Gun Manifold assemblies; Gun Manifold assemblies
© Titan Tool Inc. All rights reserved. 35 admiral™ Outlet accessories - Gun Manifold assemblies 2-Gun 5 2 3 7 3 4 1 2 5 4-Gun 2 2 2 3 1 7 3 2 5 5 4 4 1 3 1 Gun Add-On 3 2 5 Gun Manifold assemblies ITEM NO. PaRT NO. DEScRIPTION 975-102 975-104 975-111 975-302 975-304 975-311 2 - GuN 1/4” 4 - GuN 1/4”...
Page 36 - United States Sales & Service; Canadian Branch; Titan Warranty for the admiralTM airless Sprayers; admiralTM Key accessories and Service
36 © Titan Tool Inc. All rights reserved. United States Sales & Service 1770 Fernbrook Lane Minneapolis, MN 55447 www.titantool.com 200 Trowers Road, Unit 7B Woodbridge, Ontario L4L 5Z8 Phone: Fax: 1-800-526-53621-800-528-4826 Phone: Fax: 1-800-565-86651-800-856-8496 Canadian Branch 1770 Fernbro...
