Page 2 - CAUTION; WARNING
Table of Contents Safety Precautions .................................................................2 Français ..............................................................................18Español ...............................................................................20 General Descripti...
Page 3 - Gasoline Engine Safety
GAS ENGINE (WHERE APPLICABLE) Always place pump outside of structure in fresh air. Keep allsolvents away from the engine exhaust. Never fill fuel tankwith a running or hot engine. Hot surface can ignite spilledfuel. Always attach ground wire from pump unit to a groundedobject, such as a metal water ...
Page 4 - Setup; Adjusting the Trigger Tension
General Description This airless line striper is a precision power tool used to spraymany types of material for many types of applications includingparking lots, curbs, and athletic fields. Read and follow thisinstruction manual carefully for proper operating instructions,maintenance, and safety inf...
Page 5 - Preparing to Paint; Painting
6. Start the engine: a. Open the fuel valve lever. b. Move the throttle lever away from thegas tank. c. Close the engine choke lever. d. Holding the frame with one hand, pullthe starter roperapidly and firmly. Continue to hold the rope as you let itreturn. Pull and return the rope until the engine s...
Page 6 - Pressure Relief Procedure; Cleanup
12. Remove the return hose from the waste container and place it in its operating position above the container of paint. 13. Move the PRIME/SPRAY valve to the SPRAY position.14. Turn on the sprayer.15. Turn the pressure control knob slowly clockwise to increase pressure. 16. Unlock the gun by turnin...
Page 7 - Cleaning the Spray Tip; Maintenance; General Repair and Service Notes; Maintaining the Engine; Important Facts Concerning this Sprayer
Ground the gun by holding it against theedge of the metal container whileflushing. Failure to do so may lead to astatic electric discharge, which may causea fire. 15. Trigger the gun into the metal waste container until the paint is flushed out of the hose andsolvent is coming out of the gun. 16. Co...
Page 8 - Replacing the Pump ON/OFF Switch
Replacing the Pump ON/OFF Switch Electrostatic discharge (ESD) potential could causedamage to electronic pressure control. Use Titan ESDwrist strap P/N 700-1037 or equivalent when working onelectronic pressure control. 1. Perform the Pressure Relief Procedure.2. Using a Phillips screwdriver, remove ...
Page 10 - Replacing the Transducer; Servicing the Clutch Assembly
Replacing the Transducer Electrostatic discharge (ESD) potential could causedamage to electronic pressure control. Use Titan ESDwrist strap P/N 700-1037 or equivalent when working onelectronic pressure control. 1. Perform the Pressure Relief Procedure.2. Using a Phillips screwdriver, removethe four ...
Page 12 - Checking the Clutch Gap
Installing the Clutch Rotor Assembly, ClutchField and Drive Shaft Assembly 1. If the drive shaft grease seal was removed, press a new seal into the bore from which the old seal was removed. 2. From the clutch side of the gear housing, insert the drive shaft assembly into the bore, through the grease...
Page 13 - Servicing the Fluid Section; Servicing the Valves; Repacking the Fluid Section
Servicing the Fluid Section Use the following procedures to service the valves and repackthe fluid section. 1. Using a Phillips screwdriver, remove the four front cover screws. Remove the front cover. 2. Start the engine (refer to the procedures in the Operation section of this manual). Turn the pre...
Page 14 - Replacing the Filter
14 Reassemble the outlet valve assembly into the piston rod using the new o-ring, outlet valve seal, and outlet valve ballthat came with the repacking kit. Apply blue Loctite to thethreads of the outlet valve retainer. Torque the outlet valveretainer to 150 in./lbs. Never use a wrench on the piston ...
Page 15 - Replacing the Potentiometer; Accessories; Liquid Shield Plus; Piston Lube; Miscellaneous
Replacing the Potentiometer Electrostatic discharge (ESD) potential could causedamage to electronic pressure control. Use Titan ESDwrist strap P/N 700-1037 or equivalent when working onelectronic pressure control. 1. Perform the Pressure Relief Procedure.2. Pry off the pressure control knob cap to e...
Page 16 - Solution; Cause; Troubleshooting; Problem
Troubleshooting 16 © Titan Tool Inc. All rights reserved. Solution 1. Turn the pressure control knob clockwise to supply power to the unit and increase thepressure setting. 2. Inspect or take to a Titan authorized service center. 3. Fill the gas tank. 1. Rotate the PRIME/SPRAY valve clockwise to the...
Page 18 - Consignes de sécurité; AVERTISSEMENT; ATTENTION; Français
18 © Titan Tool Inc. Tous droits réservés. Consignes de sécurité Le présent manuel comprend des renseignements devant êtrelus attentivement avant toute utilisation de l'appareil. Lorsquel'un des symboles suivants apparaît, il est recommandé d'êtreparticulièrement attentif et de tenir compte des mesu...
Page 19 - Sécurité des moteurs à essence
© Titan Tool Inc. Tous droits réservés. 19 MOTEUR À ESSENCE (DANS LES CAS OÙ CELA S’APPLIQUE) Toujours placer la pompe à l’extérieur de la structure à l’airfrais. Garder tous les solvants loin de l’échappement dumoteur. Ne jamais remplir le réservoir à carburant lorsque lemoteur est en marche ou lor...
Page 20 - Precauciones de seguridad; ADVERTENCIA; PRECAUCION; Español
20 © Titan Tool Inc. Todos los derechos reservados. Precauciones de seguridad Este manual contiene información que debe leer y comprenderantes de usar el equipo. Cuando se encuentre con uno de lossiguientes símbolos, asegúrese de observar sus indicacionesde seguridad. Este símbolo indica la existenc...
Page 21 - Seguridad del motor de gasolina
© Titan Tool Inc. Todos los derechos reservados. 21 PELIGRO: PELIGRO DE EXPLOSIÓN DEBIDO A MATERIALES INCOMPATIBLES - Podríacausar lesiones severas o daños en lapropiedad. PARA PREVENIR: • No utilice materiales que contengan blanqueador o cloro.• No use solventes con hidrocarburos halogenados, tales...
Page 22 - Parts List; Main Assembly
22 © Titan Tool Inc. All rights reserved. Parts List Main Assembly 3 4 5 6 2 89 10 11 12 13 14 15 1 7 17 16 18 19 20 21 Item Part # Description Quantity 1 779-277 Cart assembly .............................................1 2 779-276 Gun holder assembly..................................1 3 862-436 H...
Page 23 - Drive Assembly
© Titan Tool Inc. All rights reserved. 23 Item Part # Description Quantity 1 704-380 ON/OFF switch ...........................................1 2 755-170 Electronic pressure control assembly .........1 3 700-139 Screw ..........................................................4 4 700-158 Potentiomete...
Page 25 - Electrical Schematic
© Titan Tool Inc. All rights reserved. 25 Fluid Section Assembly (P/N 755-173) 1 2 3 7 8 12 1314 15 16 9 19 17 18 20 21 22 10 4 56 11 23 Install lower packing with large beveled edge facing up. Install upper packing with raised lip facing down. Raised Lip Large Beveled Edge Item Part # Description Q...
Page 26 - Filter Assembly
26 © Titan Tool Inc. All rights reserved. Filter Assembly Item Part # Description Quantity 1 755-190 Filter body ...................................................1 2 730-067 Filter, 60 mesh ............................................1 3 702-251 Filter spring adapter..................................
Page 27 - Labels
© Titan Tool Inc. All rights reserved. 27 Gun Holder Assembly (P/N 779-276) Item Part # Description Quantity 1 756-034 Gun clamping knob.....................................1 2 858-644 Hex screw ...................................................2 3 858-002 Lock washer..................................
Page 28 - Limited Warranty
28 © Titan Tool Inc. All rights reserved. Limited Warranty Titan Tool Inc. warrants all equipment manufactured by it and bearing its brand names to be free from defects in material andworkmanship at the time of sale by an authorized Speeflo distributor. Titan Tool Inc. will for a period of twenty-fi...
