Page 2 - Important Safety Information; Read all safety information before
2 © Titan Tool Inc. All rights reserved. Important Safety Information · Read all safety information before operating the equipment. SavE ThESE INSTRucTIONS. This symbol indicates a hazardous situation, which, if not not avoided could result in death or serious injury.To reduce the risks of fire or e...
Page 3 - haZaRD: EXPLOSION haZaRD DuE TO; Gasoline Engine Safety; The engine exhaust from this unit contains; Specifications
© Titan Tool Inc. All rights reserved. 3 Important Safety Information · Read all safety information before operating the equipment. SavE ThESE INSTRucTIONS. haZaRD: EXPLOSION haZaRD DuE TO INcOMPaTIBLE MaTERIaLS Will cause property damage or severe injury. PREvENTION: • Do not use materials containi...
Page 4 - Table of contents
4 © Titan Tool Inc. All rights reserved. Table of contents Safety Precautions ................................................................... 2 Français............................................................................. 18 Español ..........................................................
Page 5 - Setup; Preparing a New Sprayer; Preparing Pump to Spray
© Titan Tool Inc. All rights reserved. 5 Setup Perform the following procedure before starting the engine of a gas-powered sprayer. 1. Ensure that the siphon tube and the return hose are attached and secure. 2. Attach the supplied grounding cable to a grounded object. 3. Using a wrench, attach a min...
Page 6 - Painting
6 © Titan Tool Inc. All rights reserved. 13. Turn on the sprayer. 14. Turn the pressure control knob slowly clockwise to increase pressure. 15. Unlock the gun by turning the gun trigger lock to the unlocked position. Ground the gun by holding it against the edge of the metal container while flushing...
Page 7 - Pressure Relief Procedure; Spraying; Spraying Technique
© Titan Tool Inc. All rights reserved. 7 Pressure Relief Procedure Be sure to follow the pressure relief procedure when shutting the unit down for any purpose, including servicing or adjusting any part of the spray system, changing or cleaning spray tips, or preparing for cleanup. 1. Lock the gun by...
Page 8 - cleanup; cleaning the Spray Tip; Maintenance; General Repair and Service Notes
8 © Titan Tool Inc. All rights reserved. cleanup Special cleanup instructions for use with flammable solvents: • Always flush spray gun preferably outside and at least one hose length from spray pump. • If collecting flushed solvents in a one gallon metal container, place it into an empty five gallo...
Page 10 - Replacing the Potentiometer
10 © Titan Tool Inc. All rights reserved. Replacing the Potentiometer Electrostatic discharge (ESD) potential could cause damage to electronic pressure control. use Titan ESD wrist strap P/N 700-1037 or equivalent when working on electronic pressure control. 1. Perform the Pressure Relief Procedure....
Page 11 - Electrostatic discharge (ESD) potential could cause; Replacing the Slider assembly and Slider
© Titan Tool Inc. All rights reserved. 11 5. Using a 7/8” open-end wrench, loosen and remove the fluid hose from the fitting on the bottom of the filter assembly. 6. Using a 9/16” open-end wrench, loosen and remove the return hose from the bottom of the filter assembly. 7. Using a 1/2” socket, remov...
Page 12 - NOTE: If the nipple on the cylinder does not face; Replacing the Gears
12 © Titan Tool Inc. All rights reserved. 8. Using a 21/4” wrench, loosen the fluid section jam nut. Turn the fluid section counterclockwise by until it disengages from the slider housing. 9. Using a 5/16” hex wrench, remove the four socket screws and lock washers that secure the slider housing to t...
Page 13 - Servicing the clutch assembly
© Titan Tool Inc. All rights reserved. 13 10. Inspect the pinion gear on the end of the drive shaft for wear. Replace if damaged or worn (refer to the “Servicing the Clutch Assembly” procedure in this section). 11. Inspect the output gear and the two thrust washers on the end of the crankshaft in th...
Page 14 - Removing the clutch Rotor, clutch Field, and Drive
14 © Titan Tool Inc. All rights reserved. 12. Line up the three holes in the taper lock bushing with the three holes in the clutch hub and insert the bushing into the center of the clutch hub. 13. Line up the key on the taper lock bushing with the keyway on the engine shaft and slide the assembly on...
Page 15 - Servicing the Fluid Section
© Titan Tool Inc. All rights reserved. 15 11. Line up the three screw holes and dowel pin hole on the clutch rotor with the screw holes and dowel pin on the drive shaft assembly hub. Place the clutch rotor onto the hub. 12. Using a 3/16” hex wrench, thread the three socket screws and lock washers th...
Page 17 - Troubleshooting
© Titan Tool Inc. All rights reserved. 17 Problem A. The unit will not run. B. The unit will not prime. C. The unit will not build or maintain pressure. D. Fluid leakage at the upper end of the fluid section. E. Excessive surge at the spray gun. F. Poor spray pattern. G. The unit lacks power. cause ...
Page 18 - Français; consignes de sécurite important; Lire toutes ces consignes avant
Français 18 © Titan Tool Inc. Tous droits réservés. consignes de sécurite important · Lire toutes ces consignes avant d’utiliser l’appareil. GaRDER cES cONSIGNES. Indique une situation à risque, laquelle, si elle n’est pas évitée, peut entraîner des blessures graves, voire la mort. Pour réduire les ...
Page 19 - Sécurité des moteurs à essence
Français © Titan Tool Inc. Tous droits réservés. 19 consignes de sécurite important · Lire toutes ces consignes avant d’utiliser l’appareil. GaRDER cES cONSIGNES. DaNGER : EXPLOSION cauSéE PaR DES PRODuITS INcOMPaTIBLES Ce type d’explosion peut entraîner des dommages matériels ou des blessures grave...
Page 20 - Español; Información de seguridad importante; Lea toda la información de
Español 20 © Titan Tool Inc. Todos los derechos reservados. Información de seguridad importante · Lea toda la información de seguridad antes de operar el equipo. GuaRDE ESTaS INSTRuccIONES. Indica una situación peligrosa que, de no evitarse, puede causar la muerte o lesiones graves. Para reducir los...
Page 21 - Seguridad del motor de gasolina
Español © Titan Tool Inc. Todos los derechos reservados. 21 Información de seguridad importante · Lea toda la información de seguridad antes de operar el equipo. GuaRDE ESTaS INSTRuccIONES. PELIGRO: POSIBLE EXPLOSIÓN DEBIDO a MaTERIaLES INcOMPaTIBLES Causará daños materiales o lesiones graves. PREvE...
Page 22 - Parts List; Main assembly; Description
22 © Titan Tool Inc. All rights reserved. Parts List Main assembly 8 12 13 9 10 11 7 3456 1 2 14 15 16 17181920 Item Part # Description quantity 1 0509550 Hex screw .................................................4 2 ---------- Engine ......................................................1 3 ------...
Page 23 - Drive assembly
© Titan Tool Inc. All rights reserved. 23 Drive assembly 39 3 1 4 8 9 10 15 16 13 14 11 17 12 7 6 5 2 3435 33 28 36 37 38 4041 21 22 23 2425 29 28 27 30 32 31 26 20 19 18 Item Part # Description quantity 1 9850936 ON/OFF switch .........................................1 2 0290924 Electronic pressure...
Page 25 - cart assembly; Filter assembly
© Titan Tool Inc. All rights reserved. 25 cart assembly 11 12 13 14 8 2 3 4 5 7 6 9 10 1 Item Part # Description quantity 1 0507766 Handle (includes items 2–5, 11, and 12) ..1 2 9841504 Snap button ..............................................2 3 0295609 Handle washer .................................
Page 26 - Electrical Schematic; Labels
26 © Titan Tool Inc. All rights reserved. PRIME/SPRay valve assembly (P/N 0507960) 1234 567891011 12 13 Item Part # Description quantity 1 0507736 Dowel pin ..................................................1 2 0507745 Gasket ......................................................1 3 5000529 O-ring, ...
Page 27 - accessories
© Titan Tool Inc. All rights reserved. 27 accessories Part No. Description 661-xxx Tip Assembly 661-012 Tip Guard (7/8”) 550-227 Hose, Whip End, 6’ x 1/4” 316-513 Hose, Wireless, 25’ x 1/4” 316-505 Hose, Wireless, 50’ x 1/4” 0291006 Hose, 50’ x 3/8” 0093896 Hose Connector, 1/4” x 1/4”M 812-003 Hose ...
Page 28 - Warranty; Patents; United States Sales & Service; Canadian Branch
28 © Titan Tool Inc. All rights reserved. Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or...
