Titan 433-820 - Manual

© Titan Tool Inc. All rights reserved. 5 High pressure hydraulic hose Hydraulic system shutoff valve Hydraulic motor Wet cup (use Lubrisolv only) Paint filter Fluid pump Bleed line Siphon hose Pressure bleed valve Ground lug Hydraulic fluid fill & dipstick (use Coolflo only) Pressure adjustment ...

6 © Titan Tool Inc. All rights reserved. Setup Read, understand, and follow all warnings before starting or operating this sprayer. Required tools: adjustable wrench 1. connecting the hoses: The siphon hose and bleed line hose have factory installed PTFE tape on the male end o f the hoses. Tighten t...

© Titan Tool Inc. All rights reserved. 7 Operation Startup 1. Areas must be well-ventilated to prevent hazardous operation with volatile solvents or exhaust fumes. If lacquer or other flammable materials are to be sprayed, aLWaYS locate the unit outside the immediate spraying area. Failure to do so ...

8 © Titan Tool Inc. All rights reserved. cleaning a clogged Tip 1. Follow the Pressure Relief Procedure, page 7. 2. Lock the gun trigger. 3. Unthread the safety tip guard and remove the spray tip. Wash the tip in solvent and use a tip probe to remove any clogged material. 4. Release the gun trigger ...

© Titan Tool Inc. All rights reserved. 9 Basic Engine Maintenance • For detailed engine maintenance and technical specifications refer to the separate gasoline engine manual. • All service to the engine should be performed by a dealer authorized by the engine manufacturer. To locate a dealer in your...

10 © Titan Tool Inc. All rights reserved. Troubleshooting - airless Spraying condition Possible cause correction A. Poor spray pattern and / or tails at top and bottom of the spray pattern. Worn or incorrect tip and/or insufficient atomization.Hose size or length is too small or too long.Dirty filte...

Troubleshooting - Spray Patterns condition Possible cause correction A. Tails Inadequate fluid delivery. Fluid not atomizing correctly. Increase fluid pressure. Change to small tip orifice size. Reduce fluid viscosity. Reduce hose length.Clean gun and filter(s). Reduce number of guns using pump. B. ...

12 © Titan Tool Inc. All rights reserved. Troubleshooting - hydraulic Motors condition Possible cause correction A. Oil motor stalls at bottom (no unusual heat problems). Fluid pump seat unthreaded. Valve sticking or oil motor trip rod shifter assembly separated. If connecting rod is okay, remove cy...

© Titan Tool Inc. All rights reserved. 13 Troubleshooting - Fluid Sections condition Possible cause correction A. Pump delivers on upstroke only or goes up slowly and down fast (commonly called downstroke dive). Lower foot valve ball is not seating due to trash or wear. Material to viscous to siphon...

14 © Titan Tool Inc. All rights reserved. hydra Pro Iv™ Major components 7 11 8 9 10 2 5 6 1 3 4

© Titan Tool Inc. All rights reserved. 15 8 hP honda ITEM NO. PaRT NO. DEScRIPTION Model # 433-820 422-821 1 2 3 4 441-185 Hydraulic motor pump assembly 441-574 Hydraulic motor assembly (1) 441-101 Assembly set (1) 185-551 Fluid pump assembly (1) 1 5 920-559 Outlet manifold filter assembly, 50 mesh ...

16 © Titan Tool Inc. All rights reserved. hydra Pro Iv™ hydraulic System 10 11 20 14 15 16 37 21 22 12 b a c a b 17 18 19 25 26 27 28 29 30 31 32 33 34 35 36 38 39 40 41 42 43 45 44 46 47 48 49 23 24 1 2 3 4 5 6 9 7 8

18 © Titan Tool Inc. All rights reserved. hydra Pro Iv™ Tank assembly and MobilKit 1 2 3 4 5 6 7 9 10 11 20 14 16 17 18 15 23 38 42 24 25 26 27 43 44 45 46 22 37 42 21 15 19 40 39 41 15 8 12 28 29 30 31 32 36 35 34 33 13

24 © Titan Tool Inc. All rights reserved. hydra Pro Iv™ 185-551 Fluid Pump assembly ITEM NO. PaRT NO. DEScRIPTION QTY. 1 185-981 Pin, roll 1 2 185-984 Rod, displacement 1 3 181-906 Block, pump 1 4 178-001 Packing set, upper 1 5 228-002 Nipple, hex 1 6 182-906 Spring, packing 1 7 182-007 O-ring, PTFE...

© Titan Tool Inc. All rights reserved. 25 185-551 Fluid Pump Service Information IMPORTaNT: use of non-Titan manufactured service parts may void warranty. The 185 Series Pump should receive a routine servicing after approximately 1000 hours of use or earlier if there is excessive leakage from the to...

26 © Titan Tool Inc. All rights reserved. hydra Pro Iv™ Fluid accessories 840-209 Bleed Line assembly with valve ITEM NO. PaRT NO. DEScRIPTION QTY. 1 944-028 Valve, bleed 1 2 103-101 Bleed line assembly 1 3 103-117 Tube 4 538-030 Hose assembly 4 3 2 1 944-028 Bleed valve assembly ITEM NO. PaRT NO. D...

© Titan Tool Inc. All rights reserved. 27 hydra Pro Iv™ Outlet accessories Outlet Manifold Filter assembly Part No. 920-559 ITEM NO. PaRT NO. DEScRIPTION QTY 1 920-917 Filter cap assembly 1 2 920-103 Ball, S.S. 1 3 920-004 Screen, filter, 50 mesh 1 4 920-006 Gasket, PTFE (thick) 1 5 920-070 Gasket, ...

© Titan Tool Inc. All rights reserved. 29 Key accessories and Service Kits These items may be purchased separately from your local Titan distributor. Part No. Description 103-807 Siphon hose assembly with rock catcher 1” x 4’ - 5 gallon 103-808 Siphon hose assembly with rock catcher 1” x 6 1/2 - 55 ...

32 © Titan Tool Inc. All rights reserved. Warranty Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or...