Page 2 - CAUTION; WARNING
Table of Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Grounding Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Gasoline Engine Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Français . . . . . . . . . . . . . . . . ....
Page 3 - Grounding Instructions
• Always flush unit into a separate metal container, at low pump pressure, with spray tip removed. Hold gun firmlyagainst side of container to ground container and preventstatic sparks. • Follow the material and solvent manufacturer's warnings and instructions. • Use extreme caution when using mater...
Page 4 - Gasoline Engine Safety; Warning Labels; Specifications; Gas Unit
Gasoline Engine Safety The engine exhaust from this unit contains chemicalsknown to the State of California to cause cancer, birthdefects, or other reproductive harm. 1. Honda engines are designed to give safe and dependable service if operated according to instructions. Read andunderstand the Honda...
Page 5 - Introduction; Operation; Fuel Specifications; Gasolines Containing Alcohol
© Titan Tool Inc. All rights reserved. 5 Introduction Congratulations on having selected the finest airless sprayeravailable in the world. Speeflo piston pumps are tirelessworkhorses — so tough they are virtually indestructible, evenunder the most severe service. Speeflo designs and buildsequipment ...
Page 6 - Setup; Multiple Gun
Setup Read, understand, and follow all warnings before startingor operating this sprayer. 1. Connect the siphon hose to the fluid section and the bleed hose to the bleed valve. They each have factory installed 37)( tape on the male end of the hoses and should betightened wrench tight. 2. Attach a mi...
Page 7 - Preparing a New Sprayer; Preparing to Paint
Preparing a New Sprayer If this unit is new, it is shipped with test fluid in the fluid sectionto prevent corrosion during shipment and storage. This fluidmust be thoroughly cleaned out of the system with mineralspirits before you begin spraying. Always keep the trigger lock on the spray gun in thel...
Page 8 - Painting
14. Trigger the gun into the metal waste container until the old solvent is gone and fresh solvent is coming out of the gun. 15. Lock the gun by turning the gun trigger lock to the locked position. 16. Set down the gun and increase the pressure by turning the pressurecontrol knob slowly clockwise. 1...
Page 9 - Pressure Relief Procedure; Cleanup
Pressure Relief Procedure Be sure to follow the pressure relief procedure whenshutting the unit down for any purpose, includingservicing or adjusting any part of the spray system,changing or cleaning spray tips, or preparing for cleanup. 1. Lock the gun by turning the gun trigger lock to the locked ...
Page 10 - Cleaning a Clogged Tip; Maintenance; Daily Maintenance; Lubricating the Upper Packings; Maintaining the Filter Assembly
Cleaning a Clogged Tip 1. Follow the “Pressure Relief Procedure” in the Operation section of this manual. 2. If the tip clogs, rotate the tip handle 180° until the arrow on the handle is facing the opposite of the spray directionand the handle clicks in the reverse position. 3. Trigger the gun once ...
Page 11 - Daily
Maintaining the Hydraulic System Use of Speeflo's Coolflo™ Hydraulic Fluid is mandatory inthe PowrTwin hydraulic system. Do not use any otherhydraulic fluid. Use of any other hydraulic fluid mayseriously damage the hydraulic system and will void thewarranty. 1. Check the hydraulic fluid daily. It sh...
Page 13 - Troubleshooting
Solution 1. Inspect connections for air leaks.2. Disassemble and clean.3. Inspect and adjust.4. Inspect and replace. 1. Replace.2. Adjust.3. Clean. 1. Check fluid supply.2. Clean.3. Replace. Solution 1. Remove foot valve assembly. Clean and inspect. Test foot valve by filling with water;if ball fail...
Page 14 - Hydraulic Motors; Problem
Solution 1. If connecting rod is okay, remove cylinder head plug and pop valve down. Replaceplug and start machine. If machine cyclesup and stops at bottom again, then problemis piston seat on fluid pump. Check pistonseat. Repair or replace as necessary. Ifpiston seat is okay and problem does notcha...
Page 15 - Spray Patterns
Solution 1. Fluid not atomizing correctly: Increase fluid pressure. Change to smallertip orifice size. Reduce fluid viscosity.Reduce hose length. Clean gun andfilter(s). Reduce number of guns usingpump. 1. Same as above. 1. Clean or replace nozzle tip. 1. Inspect for suction hose leak.2. Change to a...
Page 16 - Français; Sécurité; ATTENTION; AVERTISSEMENT
16 © Titan Tool Inc. Tous droits réservés. Français Sécurité Le présent manuel comprend des renseignements devant être lusattentivement avant toute utilisation de l'appareil. Lorsque l'un dessymboles suivants apparaît, il est recommandé d'être particulièrementattentif et de tenir compte des mesures ...
Page 17 - Sécurité du moteur à essence; Instructions de mise à la terre
Sécurité du moteur à essence L’État de la Californie reconnaît que les gaz d’échappement decet appareil contiennent des produits chimiques susceptibles decauser le cancer, des malformations congénitales ou pouvant êtrenocifs pour le système reproducteur. 1. Les moteurs Honda sont conçus pour être fi...
Page 18 - Seguridad; ADVERTENCIA; PRECAUCION; Español
Seguridad Este manual contiene información que debe leer y comprender antesde usar el equipo. Cuando se encuentre con uno de los siguientessímbolos, asegúrese de observar sus indicaciones de seguridad. Este símbolo indica la existencia de un peligro potencial que puedecausar lesiones graves o la mue...
Page 19 - Instrucciones para conectar a tierra; Seguridad con los motores de gasolina
© Titan Tool Inc. Todos los derechos reservados. 19 Español • Observe todos los códigos locales, estatales y nacionales apropiados que rigen las medidas de ventilación, prevención deincendios y operación. • Los Estándares de Seguridad del Gobierno de los Estados Unidos se han adoptado bajo el Acta d...
Page 20 - Parts Lists and Service Instructions; Main Assembly
20 © Titan Tool Inc. All rights reserved. Item Part # Description Quantity 1 235-107 Motor/pump assembly ..............................1 2 228-002 Adapter .....................................................1 3 200-555 Swivel adapter ..........................................1 4 840-211 Bleed hose ...
Page 21 - Belt Guard Assembly
Item Part # Description Quantity 1 590-502 Handle ......................................................1 2 449-055 Motor/pump bracket .................................1 3 862-460 Screw .......................................................1 4 590-100 Retaining ring ...................................
Page 23 - Siphon Hose Assembly
© Titan Tool Inc. All rights reserved. 23 Gas Convertokit (P/N 506-112) Item Part # Description Quantity 1 860-552 Screw .......................................................4 2 860-004 Flat washer ...............................................8 3 980-332 Engine, gas 4.0 HP, Honda ..................
Page 24 - Service Instructions; Filter Assembly
24 © Titan Tool Inc. All rights reserved. Bleed Valve Assembly (P/N 944-028) Item Part # Description Quantity 1 944-020 Valve body ................................................1 2 944-024 Knob assembly .........................................1 3 944-904 Valve seat ..................................
Page 25 - Hydraulic System; Torque and Sealant Guide
© Titan Tool Inc. All rights reserved. 25 Hydraulic System 1 2 3 4 6 7 8 9 10 11 17 18 19 20 21 25 23 29 30 28 25 31 22 24 26 27 13 14 1516 12 5 3233 34 35 37 38 39 9 10 42 46 28 24 43 4445 41 40 36 Item Part # Description Quantity 1 313-755 Knob decal ..................................................
Page 26 - Servicing the Hydraulic Motor; Hydraulic Motor
26 © Titan Tool Inc. All rights reserved. 29 See page 31 for installation instructions. 28 27 25 Item Part # Description Quantity 1 235-018 Trip retainer ..............................................2 2 141-007 O-ring .......................................................2 3 325-005 Trip spring, ....
Page 28 - Hydraulic Motor Cut-Away; Fluid Section
28 © Titan Tool Inc. All rights reserved. Hydraulic Motor Cut-Away Torque flex locknut to 10 ft./lbs. (146N/m). Use blue Loctite. Use blue Loctite on lock ring. Use hydraulic sealant. Seal lip must face up. Use hydraulic sealant. Torque head plug to 15 ft./lbs. (219 N/m). Do not over-tighten o-ring ...
Page 29 - Servicing the Fluid Section; Fluid Section Cut-Away
© Titan Tool Inc. All rights reserved. 29 Servicing the Fluid Section Disassembling the Fluid Section 1. Remove siphon tube assembly. Unthread the foot valve (16) and the pump cylinder (12) with a strap wrench. 2. Slide the retainer ring (1) up with a small screwdriver, then push the connecting pin ...
Page 30 - SIngle Gun Add-On Manifold Assemblies; Multiple Gun Add-On Manifold Assemblies; Gun Manifold Assembly
30 © Titan Tool Inc. All rights reserved. Gun Manifold Assemblies (Optional) SIngle Gun Add-On Manifold Assemblies 975-111 975-311 975-200 975-300 1 Gun Add-On 1 Gun Add-On Add-A-Gun Kit Add-A-Gun kit Item Part # Description 1/4" 3/8" 1/4" 3/8" 1 814-002 Nipple, Hex ....................
Page 31 - SAE O-Ring Fitting Installation; Accessories and Service Kits; Airless Tip Selection
© Titan Tool Inc. All rights reserved. 31 SAE O-Ring Fitting Installation Steps 1 & 2: Step 3: Step 4: Step 5: Cautions: Lubricate Lubricate Tighten nut Recess gap No gap Align Hold this part stationay Avoid screwing fitting in too far. Avoid leaving fitting too far out. Bent washer allows for o...
Page 32 - United States Sales & Service; International
32 © Titan Tool Inc. All rights reserved. Limited Warranty Titan Tool Inc. warrants all equipment manufactured by it and bearing its brand names to be free from defects in material andworkmanship at the time of sale by an authorized Speeflo distributor. Titan Tool Inc. will for a period of twenty-fi...
