Page 2 - Table of Contents
2 © Titan Tool Inc. All rights reserved. PISTON SEAL LUBRICANT Specially formulated to prevent materi- als from adhering to the piston rod, which becomes abrasive to the upper seals. Piston Lube will break down any material that may accumulate in the wet cup and keep it from drying. 8 oz individual ...
Page 3 - General Repair & Service Notes
© Titan Tool Inc. All rights reserved. 3 General Repair & Service Notes WARNING: Before proceeding, follow the Pressure Relief Procedure outlined in the “Warning” section of this manual. Additionally, follow all other warnings to reduce the risk of an injection injury, injury from mov- ing parts...
Page 4 - Maintenance Schedule; Check Piston Seal Lubricant Level WEEKLY.; Service Record
4 © Titan Tool Inc. All rights reserved. MODEL # SERIAL # DATE PURCHASED COMPANY NAME Titan Tool is in the business of designing and manufacturing spray systems and accessories that make today’s Painting Professional become more efficient and profitable. We feel that if you accurately track the main...
Page 5 - DO NOT USE EQUIPMENT BEFORE READING THIS SECTION; WARNING; HIGH PRESSURE SPRAY
© Titan Tool Inc. All rights reserved. 5 An airless spray gun requires that fluid be introduced to it at very high pressure. Fluids under high pressure, from spray or leaks, can penetrate the skin and inject substantial quantities of toxic fluid into the body. If not promptly and properly treated, t...
Page 6 - NO USE EL EQUIPO ANTES DE LEER ESTA SECCION; ADVERTENCIA; LA ROCIADURA A PRESION ALTA
6 © Titan Tool Inc. All rights reserved. Una pistola rociadora sin aire requiere que se le introduzca líquido a presión muy alta. Los líquidos bajo presión alta, de la rociadura o de las fugas, pueden penetrar en la piel e inyectar en el cuerpo cantidades considerables de líquido tóxico. Si no se at...
Page 7 - NE PAS UTILISER LE MATERIEL AVANT D’AVOIR LU CETTE SECTION; LES PULVERISATEURS A HAUTE PRESSION PEUVENT; Pression de travail maximale: 3200 psi — 221 bar
© Titan Tool Inc. All rights reserved. 7 Le liquide introduit dans un pistolet pulvérisateur sans air doit l’être à pression extrêmement élevée. Les liquides à haute pression, en provenance du pulvérisateur ou d’une fuite quelconque, sont capables de pénétrer la peau et d’injecter d’importantes quan...
Page 8 - FIRE OR EXPLOSION HAZARD; ELECTRIC MOTOR; FLUID SECTION—SOLVENTS; EXPLANATION OF THE HAZARD; PELIGRO DE INCENDIO O EXPLOSIÓN
8 © Titan Tool Inc. All rights reserved. FIRE OR EXPLOSION HAZARD Static electricity is created by the high velocity of fluid through the pump, hose and tip. If every part of the spray element is not properly grounded, sparking may occur and the system may become hazardous. Sparking may also occur w...
Page 10 - EXPLICATION DU RISQUE; HALOGENATED SOLVENTS
10 © Titan Tool Inc. All rights reserved. EXPLICATION DU RISQUE Le danger que présentent les solvants à hydrocarbure halogéné se caractérise par trois éléments clés: 1. La présence de solvants à hydrocarbure halogéné 2. La présence de pièces en aluminium ou galvanisées 3. Un matériel capable de supp...
Page 11 - Startup Procedure
© Titan Tool Inc. All rights reserved. 11 Startup Procedure WARNING: High pressure device, thoroughly read and understand the warning section located in the owner's manual and the label on the sprayer. IMPORTANT: Whenever starting or cleaning this sprayer, always reduce engine or motor speed. Additi...
Page 12 - Spraying; Spraying Technique; Practice
12 © Titan Tool Inc. All rights reserved. Spraying WARNING: POSSIBLE INJECTION HAZARD. Do not spray without the tip guard in place. Never trigger the gun unless the tip is in either the spray or the unclog position. Always engage the gun trigger lock before removing, replacing, or cleaning tip. Spra...
Page 13 - Cleaning Procedure; Pressure Relief Procedure; Troubleshooting Spray Patterns
© Titan Tool Inc. All rights reserved. 13 Cleaning Procedure WARNING: High pressure device -- Follow all safety warnings located on sprayer and in the owner's manual. Always clean using low pressure, with the spray tip removed. Always flush into a separate metal container away from the sprayer. Neve...
Page 14 - Problem; Troubleshooting Airless Pump
14 © Titan Tool Inc. All rights reserved. Flushing Specifications 1. New Sprayer: Oil is used by the factory for testing and protection. It is necessary to flush unit before spraying. a. If spraying water-base paint, flush with mineral spirits followed by water. b. If spraying oil-base paint, flush ...
Page 15 - 30V Service Instructions; Electrical Schematic for 230 Volt Motors; On/Off Switch Replacement
© Titan Tool Inc. All rights reserved. 15 230V Service Instructions Electrical Schematic for 230 Volt Motors Figure 3A Figure 3B NOTE: See page 20 for description of parts and part numbers. 46 47484942 45 TRANSDUCER 700-197 POTENTIOMETER 700-158 PRESSURE CONTROL BOARD 700-173 SWITCH MOTOR PLUG BLUE ...
Page 16 - Main Assembly
16 © Titan Tool Inc. All rights reserved. Main Assembly Figure 2
Page 17 - Replacement Labels
© Titan Tool Inc. All rights reserved. 17 Replacement Labels Part # Description Quantity 700-1017 Front Cover Label .................................................1 313-175 "Warning/Attention" (Label In French) .............1 313-1436 Wraparound Label .........................................
Page 18 - Armature Replacement; Motor Assembly
18 © Titan Tool Inc. All rights reserved. Item Part # Description Quantity 130 761-023 Screw ..................................................2 131 702-046 Rear Cover ..........................................1 133 611-405 Snap Ring............................................1 135 702-040 Outer Fan...
Page 19 - Motor Housing Replacement
© Titan Tool Inc. All rights reserved. 19 Item Part # Description Quantity 140 702-404 Outer Housing (excludes 141) .........1 141 761-244 Screw ...............................................1 142 702-084 Motor Field Assembly (110V units) (excludes 143, 144) .........................1 702-211 Motor...
Page 20 - Gear Box Assembly
21 22 23 24 2526 30 59 31 45 46 47 48 49 55 56 53 51 52 54 50 42 27282957 32 35 33 37 34 3940 41 36 38 36 44 43 21 21 20 © Titan Tool Inc. All rights reserved. Item Part # Description Quantity 21 730-260 Screw .............................................14 22 702-053 Brush Plate ......................
Page 22 - Filter Block Assembly
22 © Titan Tool Inc. All rights reserved. Filter Block Assembly Item Part # Description Quantity 201 710-069 Plug ....................................................2 202 702-011 Maxi filter housing ..............................1 203 730-083 Filter spring.........................................1 ...
Page 23 - Pump Filter
© Titan Tool Inc. All rights reserved. 23 Pressure Switch Replacement WARNING: Before proceeding, follow the Pressure Relief Procedure outlined on page 5. Additionally, follow all other warnings to reduce the risk of an injection injury, injury from moving parts or electric shock. Always unplug the ...
Page 24 - Fluid Section Assembly
24 © Titan Tool Inc. All rights reserved. Item Part # Description Quantity 300 700-735 Crank & Slide Connecting Rod Assy. .....................1 301 730-508 Retainer ...........................................1 302 700-587 Upper Guide ....................................1 304 700-603 Upper Seal ...
Page 25 - Pump Section Repair and Service; Seat Service and Repair; Fluid Section Assembly and Siphon Assembly Procedures
© Titan Tool Inc. All rights reserved. 25 Pump Section Repair and Service WARNING: Before proceeding, follow the Pressure Relief Procedure outlined on Page 5. Additionally, follow all other warnings to reduce the risk of an injection injury, injury from moving parts or electric shock. 1. Remove Safe...
Page 27 - Equipment Job History
© Titan Tool Inc. All rights reserved. 27 Job Name Foreman's Name Type of Coating Date Begun Site Gallons Sprayed Tips Used Date Completed Quantity Sizes Job Name Foreman's Name Type of Coating Date Begun Site Gallons Sprayed Tips Used Date Completed Quantity Sizes Job Name Foreman's Name Type of Co...
Page 28 - Limited Warranty
National Sales & Service 1-800-526-5362 Fax 1-800-528-4826 556 Commerce Street Franklin Lakes, NJ 07417 Canadian Branch 1-800-565-8665 Fax 1-905-856-8496 200 Trowers Road, Unit 7B Woodbridge, L4L 5Z8 International 1-201-405-7520 Fax 1-201-405-7449 556 Commerce Street Franklin Lakes, NJ 07417 USA...
