Texas Instruments TAS5601 - Manual

www.ti.com 3 Installation 3.1 Software Installation 3.2 EVM Installation 3.2.1 PSU Interface 3.2.2 Loudspeaker Connectors Installation • Access to control signal gain and data format through EVM-software graphic user interface (GUI) This section describes the software and EVM installation. Execute t...

www.ti.com 3.2.3 USB Interface 3.2.4 Digital Audio Interface SPDIF (J1/OPTO) 3.2.5 ADC Interface 3.2.6 Board Power-Up General Guidelines Installation • Connect the left speaker wires to the corresponding metal binding posts marked J2 and J4 on theTAS5601EVM board. • Connect the right speaker wires t...

www.ti.com 4 Using the EVM Software 4.1 Getting Started 4.2 Setup Tab Using the EVM Software The EVM software provides access to the TAS5706 configuration and status registers through a GUIwindow with 7 tabs for the various EVM parameters. Open the zip file (.zzp) on the installation CD shipped with...

www.ti.com 4.2.1 All Channel Shutdown 4.2.2 Advanced Features : EQ and DRC 4.2.2.1 EQ Loading and Viewing 4.2.2.2 DRC Coefficient Loading Using the EVM Software Figure 5. Volume Tab System comes up with all channel shut down asserted. To exit All Channel Shutdown , select Setup Tab, unselect All Cha...

www.ti.com Using the EVM Software Figure 6. EQ Viewer Tab Figure 7. DRC Viewer Tab SLOU219 – February 2008 TAS5601 Digital Power Amplifier With MC5601 Modulator Kit 9 Submit Documentation Feedback

www.ti.com 4.2.3 EQC/DRC Demo 4.2.4 I 2 C Tab Using the EVM Software This tab is used to compare different settings. Multiple EQ files can be loaded and switched back and forthfor listening purposes to select the golden filters. Figure 8. EQ/DRC Demo Tab Clicking on the I 2 C Interface tab displays ...

www.ti.com 4.2.4.1 I 2 C Writes and Reads Using the EVM Software Data can be written to or read from the device. Single- or multiple-byte write/read is determined by thesubaddress. If less than 0x20, single-byte access is required. Otherwise, multiple-byte access is used. Figure 9. I 2 C Single Byte...

www.ti.com 4.3 Volume Tab Using the EVM Software Select the Volume tab. Unmute the Master volume. Click on the 0 db button. Figure 11. Volume Control Tab TAS5601 Digital Power Amplifier With MC5601 Modulator Kit 12 SLOU219 – February 2008 Submit Documentation Feedback

www.ti.com 5 EQ/DRC Tool Installation 5.1 TI ALE Guide for TAS570x 5.1.1 Overview 5.1.2 Select Device EQ/DRC Tool Installation If you want to use the Texas Instruments ALE tool to create filters for the EQ and DRC parameters, unzipthe ale.zip file from the ALE directory located on the provided compa...

www.ti.com 5.2 Edit EQ Filter EQ/DRC Tool Installation Click on Edit pulldown menu, and select Edit Filter Parameters as shown in the following illustration. An EQ Filter dialog box appears as shown in the following illustration. Users then enter EQ-related data.Once finished, close the dialog box. ...

www.ti.com 5.2.1 Display the Graph EQ/DRC Tool Installation For channels 1 and 2, users can create up to seven EQ data sets. For channel 6, users can create up tofour EQ data sets. See the TAS570x data sheet for detailed technical information related to filters. To display the graph, select the Draw...

www.ti.com 5.2.2 Generate EQ Filter Data EQ/DRC Tool Installation Click on the Edit pulldown menu, and select Generate Device Data as shown in the following illustration. A Select Channel dialog box appears as shown in the following illustration. Users can select to which channel the EQ filter data ...

www.ti.com 5.2.3 Save EQ Data to File 5.3 Edit and Generate DRC Data EQ/DRC Tool Installation Click on the File pulldown menu, and select Save Device Program Data J as shown in the followingillustration. Click on the pulldown menu, and select Dynamic Range Compression for TAS570X as shown in thefoll...

www.ti.com 5.3.1 Edit and Generate Alpha Filter Data EQ/DRC Tool Installation To see the drawing with the new data, click on the Apply button. The DRC combination box allows usersto select to which DRC, 1 or 2, the data is applied. To save the data for the selected DRC, 1 or 2, click onthe Save Data...

www.ti.com 5.3.2 Save DRC Data to File 5.4 Save EQ/DRC/Alpha Data to File EQ/DRC Tool Installation When finished generating Alpha Filter data for the DRCs, the user clicks the OK button to close the dialog. To save the DRC data only, click the File pulldown menu, and select the Save As .DRC570X File...

www.ti.com 6 Jumpers and Control Utilities 6.1 Switches Jumpers and Control Utilities Reset is an active-low function. Pressing the master reset switch (S2) resets the TAS5601. TAS5601 Digital Power Amplifier With MC5601 Modulator Kit 20 SLOU219 – February 2008 Submit Documentation Feedback

www.ti.com 7 Board Layouts, Bill of Materials, and Schematics 7.1 TAS5601EVM Board Layouts Board Layouts, Bill of Materials, and Schematics Figure 12. Top Silk Screen View Figure 13. Bottom Silk Screen View SLOU219 – February 2008 TAS5601 Digital Power Amplifier With MC5601 Modulator Kit 21 Submit D...

www.ti.com 7.2 Bill of Materials 7.3 Schematics Board Layouts, Bill of Materials, and Schematics Table 2. Bill of Materials for TAS5601EVM TI SEMICONDUCTORS Item Description Ref Des Qty MFG MFG:Part No. Vendor Vendor: Part No. Alt. Part No. 1 80W 4 CH Power Amp, HTSSOP56-DCA PA1 1 Texas TAS5601DCA T...

of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: IN IN IN NC NC BTL 1 LDN PGND PGND PGND PGND THERMAL PGND PGND PGND PGND PGND PGND P...

of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: NC MC5601.SCH NC 1 LDN USB BOOT EPROM USB RESET Tue Oct 02, 2007 6 NC TAS5702 USB I/...

of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: H H 24Bit/MSB/I2S FMT1 FMT0 NC MC5601.SCH NC 2 LDN (DEFAULT) DECOUPLING DATA FORMAT ...

of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: MC5601.SCH NC NC 3 LDN SPDIF OCTOBER 2, 2007 Tue Oct 02, 2007 FROM NC 6 5V DECOUPLIN...

of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: FROM FROM FROM FROM MUTE FAULT VALID PGND PGND MC5601.SCH NC FROM NC 4 LDN SPDIF USB...

of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: of Filename: Mod: PCB Rev: Sheet Save Date: CX Schematic Rev: Design Team: Drawn By: TI Print Date PROJECT: A0 SDIN1 MCLK TO ADC JP4 JP3 JP8 JP7 3.3V@1A TO ADC TO SPDIF NC MC5601.SCH NC 5 LDN ...

www.ti.com 8 Related Documentation From Texas Instruments Related Documentation From Texas Instruments Table 3 contains a list of data manuals that have detailed descriptions of the integrated circuits and other components used in the design of the TAS5601EVM. The data manuals can be obtained at the...

EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product...

IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the l...