Teledyne 4060 - Manual

Teledyne 4060

Teledyne 4060 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
69 Page 69
70 Page 70
71 Page 71
72 Page 72
73 Page 73
74 Page 74
75 Page 75
76 Page 76
77 Page 77
78 Page 78
79 Page 79
Page: / 79

Table of Contents:

  • Page 2 – Series; ii; Teledyne; Copyright © 2010 Teledyne Analytical Instruments
  • Page 3 – Safety Messages; GENERAL; Technician Symbol
  • Page 4 – iv; Occasionally, some instruments are customized for a particular
  • Page 5 – Additional Safety Information; DANGER; COMBUSTIBLE GAS USAGE
  • Page 7 – Discharge the anode supply voltage.; Work with one hand only.
  • Page 8 – viii
  • Page 9 – Table of Contents
  • Page 10 – User Connections
  • Page 11 – Analyzer Operation
  • Page 12 – xii
  • Page 13 – List of Figures
  • Page 14 – xiv; List of Tables
  • Page 15 – Introduction; Teledyne Analytical Instruments Series 4060, Trace Aromatic; Main Features of the Analyzer; The Analyzer is sophisticated yet simple to use. A dual display on
  • Page 16 – Principle of Operation; Analyzer Description
  • Page 17 – Figure 1-1: Model 4060 Front Panel Interface
  • Page 18 – Gas purity certification.
  • Page 19 – Operational Theory; Series 4060 Analyzer for Benzene uses a FID detector and a Gas; Modes of Operation; The analyzer has 2 modes of operation depending on the position of
  • Page 20 – Addendum and Testing Results; Analysis Mode; Analyzer Subsystems
  • Page 21 – Adjustments are made using the appropriate control on the front
  • Page 22 – The Piping Diagram for the standard instrument is shown in Figure
  • Page 23 – Figure 2-2: Typical Piping Diagram for the Model 4060
  • Page 24 – The thermistor acts as the sensor in the flame guard circuit. Its
  • Page 25 – Electrometer-Amplifier PC Board
  • Page 26 – The high voltage anode power supply components are mounted on
  • Page 27 – Installation; Unpacking the Analyzer; Note: To completely slide the analyzer out of the enclosure, pull
  • Page 28 – All user connections are made on the rear panel. Consult the input-
  • Page 29 – For safe connections, no uninsulated wiring should be able to come; The power cord receptacle and fuse block are located in the same
  • Page 30 – The fuse block, at the right of the power cord receptacle, accepts US
  • Page 31 – Channel 1, negative ground; Ppb
  • Page 32 – Table 3-3: Analog Range ID Output—Example; Range; Threshold Alarm 1; Can be configured as failsafe or non-failsafe
  • Page 33 – Note: Reset by pressing the STANDBY button to remove power.; Pin Contact
  • Page 34 – Remote Calibration; Pin; Remote Calibration Protocol:
  • Page 35 – When the CRC closes, remove the span command.; A serial digital input/output for local network protocol. At this
  • Page 36 – The input functions using RS-232 that have been implemented
  • Page 37 – The RS-232 protocol allows some flexibility in its
  • Page 38 – Gas connections to the instrument are made at the 1/8”or 1/4”
  • Page 39 – CARRIER GAS: NITROGEN GAS, ULTRA ZERO GRADE WITH THC; Normally, four supporting gases of different composition (see
  • Page 40 – The sample bypassed by the back-pressure regulation system vents; Placing the System in Operation
  • Page 41 – Operation; Addendum and; Fuel; Gas Connections
  • Page 42 – Make the following checks of the installation before proceeding; Activating the Support Gases; All gas controls are located on the front panel as shown in Figure 1-
  • Page 43 – Note: Adjust fuel settings only when the red LED (flame failure
  • Page 44 – Verification of the Flame Guard Circuit; Although the Model 4060 has been programmed for your application
  • Page 46 – Auto; ANALYZE
  • Page 47 – ANALYSIS SCREEN
  • Page 48 – ESCAPE
  • Page 49 – MAIN MENU; AUTOCAL is an optional feature not
  • Page 50 – Enter; Span Begin
  • Page 51 – Pressing enters the SPAN mode in the Sampling Phase.
  • Page 52 – Analyze Mode
  • Page 53 – Note: For the purpose of example, Alarm 2 has been set
  • Page 54 – The latching property configures the alarm such that the; RELEASING A LATCHED ALARM:; When alarm conditions are
  • Page 56 – CH1 Gain; Not applicable to the 4060 configuration.
  • Page 57 – Note: If you require highly accurate AUTOCAL timing, use; PASSWORD; AUTO SPAN Enabled
  • Page 58 – Note: For instruction on how to set the parameters, please refer
  • Page 59 – Note: If you use password security, it is strongly advised to keep a; ENTERING A PASSWORD; AUTOCAL
  • Page 60 – Enter a Password
  • Page 61 – Reenter a new Password; Note: If you log off the system using the
  • Page 63 – >From the MAIN MENU, scroll to the STANDBY
  • Page 65 – Maintenance & Troubleshooting
  • Page 66 – Measuring Circuit Electrical Checks; negative
  • Page 67 – If the checks outlined above indicate that conditions are normal,
  • Page 68 – Whenever the flame guard and anode power supply printed circuit; Temperature Control Electronic Check; Consult the 4060 schematic and assembly drawings, as well as the
  • Page 69 – Note: If any of the components located inside the isothermal; Ignition and/or Flame Guard Circuit Checks; If the flame guard circuit will not hold the flame-out lamp off when
  • Page 71 – Printed Circuit Board Descriptions; Flame Guard and Anode Power Supply PCB; Anode Power Supply; : The high voltage anode power supply; Flame Guard Circuit:; A thermistor-controlled, comparator circuit is
  • Page 72 – Proportional Temperature Controller PCB
  • Page 73 – When the temperature reaches the selected control point, pin 13
  • Page 75 – Appendix; A.1 Specifications and Initial Settings:; Signal Output
  • Page 76 – A.2 Recommended Spare Parts List; Analytical Instruments
  • Page 77 – PC Board Assemblies
  • Page 79 – Appendix B; B1 Addendum and Testing Results
Loading the manual

INSTRUCTION, OPERATING AND

MAINTENANCE MANUAL FOR

SERIES 4060

DANGER

Toxic and/or flammable gases or liquids may be present in this monitoring system.

Personal protective equipment may be required when servicing this instrument.

Hazardous voltages exist on certain components internally which may persist for
a time even after the power is turned off and disconnected.

Only authorized personnel should conduct maintenance and/or servicing. Before
conducting any maintenance or servicing, consult with authorized
supervisor/manager.

P/N M76417

DATE 06/29/10

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Series; ii; Teledyne; Copyright © 2010 Teledyne Analytical Instruments

Series 4060 ii Teledyne Analytical Instruments Copyright © 2010 Teledyne Analytical Instruments All Rights Reserved. No part of this manual may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any other language or computer language in whole or in part, in an...

Page 3 - Safety Messages; GENERAL; Technician Symbol

Series 4060 Teledyne Analytical Instruments iii Safety Messages Your safety and the safety of others is very important. We have provided many important safety messages in this manual. Please read these messages carefully. A safety message alerts you to potential hazards that could hurt you or others...

Page 4 - iv; Occasionally, some instruments are customized for a particular

Series 4060 iv Teledyne Analytical Instruments CAUTION: THE ANALYZER SHOULD ONLY BE USED FOR THE PURPOSE AND IN THE MANNER DESCRIBED IN THIS MANUAL. IF YOU USE THE ANALYZER IN A MANNER OTHER THAN THAT FOR WHICH IT WAS INTENDED, UNPREDICTABLE BEHAVIOR COULD RESULT POSSIBLY ACCOMPANIED WITH HAZARDOUS ...

Other Teledyne Models

All Teledyne Other