Stanley 2005 Series - Manual

The S&G

©

X

03

D-Drive

™

lock combines ease of operation with

security and flexibility. Its advanced electronic circuit design

makes it easy to open and easy to change codes. Follow these

instructions carefully to get the best possible use from your lock.

I

ntroductIon

• This S&G

©

X

03

D-Drive

™

lock is shipped from the factory in

multi-user mode with a

factory master code

of 1 2 3 4 5 6

#. This code can be used to open the lock and set or change

codes. You should set the lock to your own, unique

master

code

.

• Your lock can be programmed with a

management reset code

that can be used to regain control of the lock in the event the

master code

is lost. The

management reset code

must be

programmed into the lock before the

master code

is changed

for the first time.

• At your discretion, the lock can be set to accept a

supervisor

code

, up to seven different

user codes,

and a

time delay

override code

. The

master code

holder and the

supervisor

code

holder (if a

supervisor code

is set) are responsible

for maintaining the number of active users programmed into

each lock. The

master code

holder and the

supervisor code

holder can create and delete user codes.

• The

master code

is designated as code #0. The

supervisor

code

(if set) is designated as code #1. The

user codes

(if

set) are designated by user position numbers 2, 3, 4, 5, 6, 7,

and 8. The

time delay override code

(if set) is designated as

code #9.

• Each time a button is pressed, the lock acknowledges it

by sounding a “beep,” and the LED on the keypad will light

momentarily as the “beep” sounds. If it does not, check your

battery (or batteries) to make sure it is fresh and connected

properly, then try again.

• All codes must contain six digits or six letters. Any digit or

letter can be used as many times as you wish. For instance,

the following codes (while not recommended) will operate the

lock: 5 5 5 5 5 5 # OR J J J J J J #

• All codes end with #. This signals the

lock that you have finished entering all

digits of the code.

• If you pause more than 10 seconds

between button presses when entering

a code, the lock will assume you do not

want to continue, and it will reset itself

to the original code. To open the lock,

begin the code entry sequence once again from the first step.

• If you realize you have pressed an incorrect button when

entering a code, press

✽

or simply pause ten seconds or more,

then begin entering your code again.

• If five incorrect codes are entered in a row, the S&G

©

X

03

D-

Drive

™

lock will shut down for a period of ten minutes. This

is a security feature. Entering a code during this period will

result in two long error tones (braps). Pressing any buttons

during the lockout period will not affect the penalty timer.

After ten minutes, the lock should operate normally.

The lock can also go into the lockout period during

programming if it interprets an incorrect programming

sequence as five or more consecutive incorrect code entries.

If the lock emits two long error tones (braps) during repeated

programming attempts, it is in lockout mode. Wait ten

minutes, then try again.

• For UL installations, the maximum number of working codes

allowed is one.

• Personal data which can be directly related to a code holder,

such as a birthdate, should not be used in making up a lock

code. Avoid codes which can be easily guessed.

• After the lock is changed to a new code, the lock function

must checked by locking and unlocking it several times with

the container door open. Make sure it functions correctly

before closing the door.

Note: This lock has been Listed by Underwriters Laboratories for use with the following

S&G keypad(s): 6130-2XX and 6130-3XX

© Copyright 2006, Sargent & Greenleaf

Document 630-735

Revised 7/25/06

Sargent & Greenleaf, Inc.

A Wholly Owned Subsidiary of Stanley Security Solutions, Inc.
PO Box 930, Nicholasville, Kentucky 40356 USA
Phone (859) 885-9411
Phone (800) 826-7652
FAX (859) 887-2057
FAX (800) 634-4843

Sargent & Greenleaf S.A.

9, chemin du Croset

1024 Ecublens, Switzerland

Phone +41-21 694 34 00

FAX +41-21 694 34 09

O

perating

i

nstructiOns

S&G

®

Z

03

D-Drive

™

Multi-User Electronic Safe Lock

2005 Series