Stanley SD67 - Manual - manualsarea.com

Page 3 - TABLE OF CONTENTS; WARNING; IMPORTANT

SD67 User Manual ◄ 3 TABLE OF CONTENTS SERVICING THE STANLEY HYDRAULIC SPIKE DRIVER. This manual contains safety, operation, and routine maintenance instructions. Stanley Hydraulic Tools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized ...

Page 4 - SAFETY SYMBOLS; LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE

4 ► SD67 User Manual SAFETY SYMBOLS Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety...

Page 5 - SAFETY PRECAUTIONS

SD67 User Manual ◄ 5 SAFETY PRECAUTIONS Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re- view them carefully before operating...

Page 7 - HOSE TYPES; HOSE SAFETY TAGS

SD67 User Manual ◄ 7 HOSE TYPES The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: C...

Page 8 - HOSE RECOMMENDATIONS; Tool to Hydraulic Circuit Hose Recommendations

8 ► SD67 User Manual HOSE RECOMMENDATIONS Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ...

Page 9 - HTMA / EHTMA REQUIREMENTS

SD67 User Manual ◄ 9 HTMA / EHTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Tem...

Page 10 - OPERATION; PRE-OPERATION PROCEDURES; PREPARATION FOR INITIAL USE; OPERATING PROCEDURES

10 ► SD67 User Manual OPERATION PRE-OPERATION PROCEDURES PREPARATION FOR INITIAL USE Each unit as shipped has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the unit was not damaged in shipping and does not contain packing debris is all that is required. CHECK...

Page 11 - TOOL PROTECTION & CARE

SD67 User Manual ◄ 11 TOOL PROTECTION & CARE NOTICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Always store an idle tool in a clean dry space, safe from damage or pilferage. • Do not exceed the rated limits or use the to...

Page 12 - TROUBLESHOOTING

12 ► SD67 User Manual TROUBLESHOOTING Problem Cause Solution Spike driver does not run. Power unit not functioning. Check power unit for proper flow and pressure (7–10 gpm I 26–38 lpm, 2000 psi I 140 bar). Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at port...

Page 13 - CHARGING THE ACCUMULATOR; TESTING THE ACCUMULATOR

SD67 User Manual ◄ 13 CHARGING THE ACCUMULATOR To check or charge the accumulator the following equip- ment is required: • Accumulator tester (Part Number 02835).• Charging assembly (P/N 31254—includes a regula - tor, hose and fitting). • Nitrogen bottle with an 800 psi/56 bar minimum charge. 1. On ...

Page 15 - SD67 PARTS ILLUSTRATION

Page 16 - MODEL DESCRIPTIONS; SD67 PARTS LIST

16 ► SD67 User Manual ITEM PART NO. QTY DESCRIPTION 1 24067 1 RETAINING RING 2 04055 1 WASHER 3 04056 1 ROD WIPER * 4 26451 1 BUSHING 5 01362 1 O-RING 5/16 × 7/16 × 1/16 * 6 00293 1 O-RING 11/16 × 7/8 × 3/32 * 7 20515 1 VALVE SPOOL 8 04058 1 SPRING 9 07628 4 CAPSCREW 10 20511 1 LEVER 11 28369 1 HAND...

Stanley SD67 - Manual

Table of Contents:

Summary

Other Stanley Models