Spalding 211014 - Manual

10 P/N 211014 03/05 SECTION A: ASSEMBLE THE POLES Wood Scrap P-2 P-1 5" (13 cm) 5" (13 cm) P-1 P-3 P-2 Pole Identification Sticker Pole Identification Sticker 2. While maintaining alignment, bounce middle pole section (P-2) into top section (P-1) using a wood scrapas shown until the top pole...

12 P/N 211014 03/05 SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’vefinished this section. 1. Insert axle (P-5) through wheel bracket (P-4). Secure wheels (P-28) to axle using pushnuts (H-1).Carefully tap pushnuts (H-1) onto axle with hammer or mallet. P-4 P-28 P-28 H...

15 03/05 P/N 211014 5. P-13 P-13 Secure tank struts (P-13) to pole using bolt (H-3), washers (H-4) and nut (H-23) as shown. Placebolt cover (H-7) over exposed end of bolt as shown. Rotate non-secured ends of tank struts (P-13)outward to mounting holes in tank as shown. TWO PEOPLE REQUIREDFOR THIS PR...

19 03/05 P/N 211014 SECTION C: ASSEMBLE THE ELEVATOR SYSTEM & BACKBOARD This is what your system will look like when you’vefinished this section. Securely rest the assembly on sawhorse. Identifyelevator tubes (P-19 and P-20). P-19 LowerElevatorTube Toward Board Toward Pole P-20 UpperElevatorTube...

20 P/N 211014 03/05 P-1 P-18 P-20 H-15 H-15 P-19 H-17 P-20 P-19 P-17 H-18 H-19 H-18 1. While the system is securely resting on the sawhorse. Install triangle plates (P-17) and elevator tubes (P-19 and P-20) to top pole section (P-1) as shown. Installpole cap (P-18) at this time. P-17 COMPLETED ASSEM...

23 03/05 P/N 211014 7. P-31 H-33 H-32 P-30 H-31 Install Slam Jam Rim to Backboard P-29 P-32 H-31 H-32 H-33 A B C D E A. Fit rim (P-29) securely into bracket (P-30) as shown. Allow T-bolt (H-31) to slip through center hole in rim (P-29). B. Install reinforcement bracket (P-31) onto T-bolt (H-31) as s...

25 03/05 P/N 211014 H-18 H-15 P-1 P-20 P-19 P-17 P-11 9. Install handle assembly (P-10 and P-11) to lower elevator tubes (P-19) using bolt (H-18), spacers (H-14),and nut (H-15) as shown. P-20 P-19 H-14 H-14 Secure the handle assembly (P-10 & P-11) to pole bracket (P-9) usingbolt (H-30) and nut (...

26 P/N 211014 03/05 P-20 P-12 H-15 P-20 11. Insert bolt (H-18) through left side upper elevator tube (P-20),then stretch spring (P-12) onto bolt (H-18). Continue insertingbolt (H-18) through right side upper elevator tube (P-20) andsecure with nut (H-15). H-18 P-12 USE EYE PROTECTION WHEN INSTALLING...

27 03/05 P/N 211014 12. Install net clips (H-28). CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly sothat second “arm” slides over the top of the first “arm” as shown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. ...

28 P/N 211014 03/05 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NET CLIP SIDE VIEW NET NET CLIP 13. H-28 P-33 Install net (P-33). P-33

29 03/05 P/N 211014 SECTION D: INSTALL FRONT COVER & HANDLE 1. Attach front cover (P-22) to hinge tubes (P-16) using carriage bolts (H-27) and flange nuts (H-11) asshown. P-22 H-27 H-11 P-16 Upright system and fill base (P-8) with water (approximately 40 gallons) and snap fill cap (P-24) in plac...

30 P/N 211014 03/05 1. Roll assembly to desiredplaying area. Secure assemblyto ground using strap (P-26)and tie down stake (P-25). P-26 P-25 P-8 SECTION E: SECURING THE SYSTEM & APPLYING LABEL 2. Apply Height Adjustment and Moving Label (P-27) tofront of pole, where it is clearly visible. Peel p...