Spalding 211014 - Manuals

Spalding 211014 – Manual in PDF format online.

Manuals:

Manual

Manual Spalding 211014

Summary

Page 2 - WARNING

2 P/N 211014 03/05 201246 11/04 In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339 FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. WARNING • DO NOT HANG on the ri...

Page 3 - NOTICE TO ASSEMBLERS; SAFETY INSTRUCTIONS

3 03/05 P/N 211014 IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. NOTICE TO ASSEMBLERS ALL Huffy Sports basketball systems, including those used for DISPLAYS, MUST be assembledand ballasted with sand or water accordi...

Page 5 - PARTS IDENTIFIER

5 03/05 P/N 211014 PARTS LIST (SEE PARTS IDENTIFIER) Item Qty Part No Description P-1 1 908164 Top Pole Section P-2 1 908107 Middle Pole Section (with Label) P-3 1 908165 Bottom Pole Section P-4 2 900223 Wheel Bracket P-5 2 206940 Axle, 21" Long P-6 2 226403 Wheel 6” P-7 1 206990 Bracket, Reinfo...

Page 10 - SECTION A: ASSEMBLE THE POLES; Correctly identify each pole section.

10 P/N 211014 03/05 SECTION A: ASSEMBLE THE POLES Wood Scrap P-2 P-1 5" (13 cm) 5" (13 cm) P-1 P-3 P-2 Pole Identification Sticker Pole Identification Sticker 2. While maintaining alignment, bounce middle pole section (P-2) into top section (P-1) using a wood scrapas shown until the top pole...

Page 12 - SECTION B: ASSEMBLE THE BASE; • Support Pushnut/Axle

12 P/N 211014 03/05 SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’vefinished this section. 1. Insert axle (P-5) through wheel bracket (P-4). Secure wheels (P-28) to axle using pushnuts (H-1).Carefully tap pushnuts (H-1) onto axle with hammer or mallet. P-4 P-28 P-28 H...

Page 15 - ORIENTATION OF STRUTS

15 03/05 P/N 211014 5. P-13 P-13 Secure tank struts (P-13) to pole using bolt (H-3), washers (H-4) and nut (H-23) as shown. Placebolt cover (H-7) over exposed end of bolt as shown. Rotate non-secured ends of tank struts (P-13)outward to mounting holes in tank as shown. TWO PEOPLE REQUIREDFOR THIS PR...

Page 19 - SECTION C: ASSEMBLE THE ELEVATOR SYSTEM & BACKBOARD; Toward

19 03/05 P/N 211014 SECTION C: ASSEMBLE THE ELEVATOR SYSTEM & BACKBOARD This is what your system will look like when you’vefinished this section. Securely rest the assembly on sawhorse. Identifyelevator tubes (P-19 and P-20). P-19 LowerElevatorTube Toward Board Toward Pole P-20 UpperElevatorTube...

Page 20 - While the system is securely resting on the sawhorse.; COMPLETED ASSEMBLY

20 P/N 211014 03/05 P-1 P-18 P-20 H-15 H-15 P-19 H-17 P-20 P-19 P-17 H-18 H-19 H-18 1. While the system is securely resting on the sawhorse. Install triangle plates (P-17) and elevator tubes (P-19 and P-20) to top pole section (P-1) as shown. Installpole cap (P-18) at this time. P-17 COMPLETED ASSEM...

Page 23 - Install Slam Jam Rim to Backboard

23 03/05 P/N 211014 7. P-31 H-33 H-32 P-30 H-31 Install Slam Jam Rim to Backboard P-29 P-32 H-31 H-32 H-33 A B C D E A. Fit rim (P-29) securely into bracket (P-30) as shown. Allow T-bolt (H-31) to slip through center hole in rim (P-29). B. Install reinforcement bracket (P-31) onto T-bolt (H-31) as s...

Page 25 - Note orientation of handle.

25 03/05 P/N 211014 H-18 H-15 P-1 P-20 P-19 P-17 P-11 9. Install handle assembly (P-10 and P-11) to lower elevator tubes (P-19) using bolt (H-18), spacers (H-14),and nut (H-15) as shown. P-20 P-19 H-14 H-14 Secure the handle assembly (P-10 & P-11) to pole bracket (P-9) usingbolt (H-30) and nut (...

Page 26 - TOP VIEW

26 P/N 211014 03/05 P-20 P-12 H-15 P-20 11. Insert bolt (H-18) through left side upper elevator tube (P-20),then stretch spring (P-12) onto bolt (H-18). Continue insertingbolt (H-18) through right side upper elevator tube (P-20) andsecure with nut (H-15). H-18 P-12 USE EYE PROTECTION WHEN INSTALLING...

Page 27 - Push second “arm” back and into ram as shown.

27 03/05 P/N 211014 12. Install net clips (H-28). CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly sothat second “arm” slides over the top of the first “arm” as shown.Push in direction indicated by arrows. Push second “arm” back and into ram as shown. ...

Page 28 - Insert net into bottom of clip as shown.

28 P/N 211014 03/05 Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position.Net must be centered through clip. NET NET CLIP SIDE VIEW NET NET CLIP 13. H-28 P-33 Install net (P-33). P-33

Page 29 - SAND

29 03/05 P/N 211014 SECTION D: INSTALL FRONT COVER & HANDLE 1. Attach front cover (P-22) to hinge tubes (P-16) using carriage bolts (H-27) and flange nuts (H-11) asshown. P-22 H-27 H-11 P-16 Upright system and fill base (P-8) with water (approximately 40 gallons) and snap fill cap (P-24) in plac...

Page 30 - SECTION E: SECURING THE SYSTEM & APPLYING LABEL; Peel protective

30 P/N 211014 03/05 1. Roll assembly to desiredplaying area. Secure assemblyto ground using strap (P-26)and tie down stake (P-25). P-26 P-25 P-8 SECTION E: SECURING THE SYSTEM & APPLYING LABEL 2. Apply Height Adjustment and Moving Label (P-27) tofront of pole, where it is clearly visible. Peel p...