Spalding 211376A - Manuals - manualsarea.com

Page 2 - any excess paint from holes if necessary.; cualquier exceso de pintura, si es necesario.

2 P/N 211376A 05/03 BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular ...

Page 3 - WARNING; HEIGHT ADJUSTMENT

05/03 P/N 211376A 3 FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • ...

Page 6 - concrete is set up to clamp assembly as shown below.; WAIT MINIMUM OF

6 P/N 211376A 05/03 6. Insert ground sleeve (4) and pole section (3) into hole. Fillremaining hole with concrete. Tamp down concrete torelease air pockets and build drainage hill. Center and levelground sleeve assembly in hole. Check leveling on all sidesseveral times while concrete is curing. NOTE:...

Page 7 - TWO PERSON MINIMUM

05/03 P/N 211376A 7 C O N C R E TE 1" (2.54cm) IMPORTANT! Bounce pole top (1) and middle section (2) together as shown until they no longer move toward tapedreference mark. NOTE: Pole sections should have a 4-1/2" (11.4 cm)minimum overlap. IMPORTANT! Add bottom pole section (3) to assembly. ...

Page 8 - ELEVATOR HOLES MUST BE PARALLEL WITH

8 P/N 211376A 05/03 14. Lower clamp cover (12) over clamps and snap intoproper position. ;;; ;;; 13. Secure clamps (7) around pole section as shown. Referto Step 4. Tighten completely. 12. ;; ;;; ;;; 11 12 12 3 12 IMPORTANT! ELEVATOR HOLES MUST BE PARALLEL WITH PLAYING SURFACE. TWO PERSON MINIMUM RE...

Page 9 - DO NOT OVER; TOP

05/03 P/N 211376A 9 FRON T 17 14 19 13 18 16 14 15 15 18 14 15. Beginning with top hole in left and right screw jack support plates (16 & 17), install elevator tubes (15) topole as shown. Then secure lower holes in support plates to pole. NOTE: Not all holes in support plates (16 & 17) are u...

Page 10 - FRONT

10 P/N 211376A 05/03 1 7 98 11 7' 2.1m 20 22 21 24 24 IMPORTANT! DO NOT OVER TIGHTEN. 23 POLE 14 18 18 21 15 15 16 17 14 17. 18. Center screw jack (21) between support plates (16 & 17) and secure as shown below. Attach logo label (22) to height indicator cover (23).Place cover (23) over screw ja...

Page 14 - OUTSIDE VIEW; Refer To Instructions

14 P/N 211376A 05/03 24. 25. ½ 33 31 29 Attach rim (33). Note: Mounting nuts (29) andbolts (31) supplied with rimhardware. USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. Install ...

Page 15 - Height Adjustment; HOOK; Slide net into outer hook as shown.; FRONT VIEW

05/03 P/N 211376A 15 Position looped end of height adjustment crank(36) onto hook as shown. Rotate crank handleto raise or lower backboard. View label (20) todetermine approximate backboard height. 27. 26. Height Adjustment HOOK 36 20 STORE CRANK OUT OF REACH OF CHILDREN. DO NOT ALLOW CHILDREN TO AD...

Page 16 - REGULATION RIM

16 P/N 211376A 05/03 HUFFY HUFFY SPORTS 10 feet (3.05 m) 37 REGULATION RIM HEIGHT IS 10 FEET (3.05 M). 28. Apply height adjustment label (37) to front ofpole as shown. Secure pole pad (32)as shown. 29. 32

Page 17 - YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.

05/03 P/N 211376A 17 PARTS LIST HARDWARE IDENTIFIER * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. Item Qty. Part No. Description 1 1 900757 Top Pole Section 2 1 900874 Middle Pole Section, Flared End 3 1 908215 Bottom Pole Section 4 1 206500 Ground Sleeve, Square 5 2 201124 Lock Nut, Hex Head, 3/8 x 1...