Spalding M611411 - Manuals - manualsarea.com

Page 2 - MOVING SYSTEM; WARNING

2 ID# M611411 12/05 10-3/4" High 4" Wide PMS 021 for Warning Owner must ensure that all players know and follow these rules for safe operation of the system. WARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when ...

Page 3 - NOTICE TO ASSEMBLERS; SAFETY INSTRUCTIONS

3 12/05 ID# M611411 IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. NOTICE TO ASSEMBLERS ALL basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instr...

Page 4 - FRONT VIEW; BOARD STYLE

4 ID# M611411 12/05 Get to know the basic parts of your basketball system... FRONT VIEW BOARD STYLE MAY VARY NOTE: POLE RIM BASE WHEEL CARRIAGE ASSEMBLY BOARD

Page 5 - PARTS LIST; Description

5 12/05 ID# M611411 PARTS LIST Item Qty. Part No. Description 1 1 206646 Tank (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel 4 1 908200 Top Pole Section 5 1 908246 Middle Pole Section with Label 6 1 900644 Bottom Pole Section Assembly 7 1 203041 Nut, Hex Flange, 3/8-16 8 1 Net 9 1 201342 Wheel Brack...

Page 7 - MBBLLEE TTHHEE PPOOLLEESS; that will be used as a reference point in the next step.; TOP; Reference Stickers

7 12/05 ID# M611411 SSEECCTTIIOONN AA:: AASSSSEEM MBBLLEE TTHHEE PPOOLLEESS 1. Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. 5 4 6 TOP MIDDLE BOTTOM Reference Stickers

Page 8 - HOLE; TROUGH; TROUGH; Wood Scrap

8 ID# M611411 12/05 2. IMPORTANT! ONCE POLE SECTIONS ARE POUNDED TOGETHER- THEY CANNOT BE TAKEN APART THE IDENTIFICATION STICKER ISLOCATED 3-3/4" FROM THE ENDOF THE POLE. WHEN PROPERLYPOUNDED TOGETHER, THE POLESECTIONS SHOULD HAVE A 2-1/2"MINIMUM OVERLAP, LEAVING 1-1/4" BETWEEN THE OVERL...

Page 9 - SECTION B: ASSEMBLE THE BASE

9 12/05 ID# M611411 SECTION B: ASSEMBLE THE BASE Install wheel axle (2) through wheel bracket (9) and install wheels (3) onto wheel axle (2) with spacers (10) as shown. Attach wheel carriage assembly to base (1) with bolt (13), washer (22), and nut (7) as shown. FINGER TIGHTEN - NO TOOLS REQUIRED. A...

Page 10 - FIG B

10 ID# M611411 12/05 Attach pole assembly to tank assembly as shown. Secure pole assembly to tank and wheel bracket by turning the pole assembly clockwise as shown. Tightenpole completely and further rotate pole until struts are aligned correctly as shownin FIG B. 5. FIG B The pole should be turneda...

Page 12 - Final adjustments will be made in Step 10.

12 ID# M611411 12/05 7. Mount brackets (20 & 26) to backboard and finger tighten as shown. NOTE: Final adjustments will be made in Step 10. 20 11 24 25 26 27 26 27 BOARD STYLE MAY VARY NOTE:

Page 13 - Install Slam Jam Rim to Backboard

13 12/05 ID# M611411 28 21 19 26 27 Install Slam Jam Rim to Backboard 18 19 21 A B D E A • Fit rim (18) securely into bracket (26) as shown (Allow "T"-bolt (27) to slip through center hole in rim (18). B • Install reinforcement bracket (28) onto “T” bolt (27) as shown. C • Install spring (29...

Page 14 - Peel protective

14 ID# M611411 12/05 XSHBM01.EPS211208 SAWHORSE OR SUPPORT TABLE 9. Support pole and tank assembly over support table.Carefully slide backboard components onto pole. TWO PEOPLE REQUIREDFOR THIS PROCEDURE.FAILURE TO FOLLOW THISWARNING COULD RESULT INSERIOUS INJURY AND/ORPROPERTY DAMAGE. WARNING! DO N...

Page 15 - GALLONS OF

15 12/05 ID# M611411 10 feet (3.05 m) 15 HEIGHT AND MOVING LABELMUST NOT OBSTRUCTFACTORY ATTACHEDWARNING LABEL. 5E2356 05/05 1 3 2 MOVING SYSTEM 1. While holding pole, rotate basketball system forwarduntil wheels engage withground. 2. Move basketball system to desired location. 3. Carefully rotate b...