Page 2 - Instructions; General safety instructions
Instructions 4 1 Instructions 1.1 General safety instructions Risk of personal injury • WARNING: The appliance and its accessible parts become hot during use. • Never try to put out a fire or flames with water: turn off the appliance and smother the flames with a fire blanket or other appropriate co...
Page 3 - Risk of damaging the appliance
Instructions 5 EN • Do not use aerosols in the vicinity of this appliance whilst it is in use. • Switch off the appliance after use.• Do not modify this appliance.• Do not try to repair the appliance yourself or without the intervention of a qualified technician. • Do not pull the cable to remove th...
Page 5 - For this appliance
Instructions 7 EN • This domestic appliance is not connected to a device for extracting combustion products. It must be installed and connected in accordance with current installation regulations. Pay particular attention to the relevant requirements regarding ventilation. For this appliance • Do no...
Page 6 - How to read the user manual; Power voltage
Instructions 8 To dispose of the appliance:• In order to prevent children from becoming trapped inside, remove the doors (if present) and leave the accessories (racks and trays) in the positions of use. • Cut the power supply cable and remove it along with the plug. • Deliver the appliance to the ap...
Page 7 - Description; General Description; AUX
Description 9 EN 2 Description 2.1 General Description 1. Control panel2. Auxiliary Burner ( AUX ) 3. Rapid burner reduced ( RR ) 4. Ultra-rapid burner with external crown ( UR2 int. ) 5. Ultra-rapid burner with internal crown ( UR2 ext. ) 6. Hob grid 2.2 Symbols Cooking zones Front Rear Central ext...
Page 8 - Burner knobs; Available accessories; Raised pan stand
Description 10 Burner knobs For lighting and adjusting the hob burners. Press and turn the knobs anti-clockwise to in order to light the relative burners. Turn the knobs to the zone between the maximum and minimum setting to adjust the flame. Return the knobs to the position to turn off the burners....
Page 9 - Use; Improper use
Use 11 EN 3 Use 3.1 Instructions 3.2 First use 1. Remove any protective film from the outside or inside of the appliance, including accessories. 2. Remove any labels (apart from the technical data plate) from accessories. 3. Remove and wash all the appliance's accessories (see 4 Cleaning and mainten...
Page 10 - Always check that the control
Use 12 Positioning the pan stands The pan stands are provided unassembled on the hob. To install the grids correctly, follow the instructions as shown in the figure. Correct positioning of the flame-spreader crowns and burner caps Before lighting the hob burners, check that the flame-spreader crowns...
Page 11 - Limitations on griddle use
Use 13 EN Limitations on griddle use A few precautions are necessary if you wish to use a griddle:• The griddles should not exceed the perimeter of the hob. • Aluminium griddles with Teflon anti-stick coating should be pre-heated for a maximum of 5 minutes in order to avoid damage to the appliance a...
Page 12 - Cleaning and maintenance; Cleaning the appliance; Ordinary daily cleaning
Cleaning and maintenance 14 4 Cleaning and maintenance 4.1 Instructions 4.2 Cleaning the appliance To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. Ordinary daily cleaning Always and only use specific products that do not contain abrasives or c...
Page 13 - Knobs
Cleaning and maintenance 15 EN Knobs The knobs should be cleaned with a soft cloth dampened with warm water, then dried carefully. They can easily be removed by pulling them upwards. Igniters and thermocouples For correct operation the igniters and thermocouples must always be perfectly clean. Check...
Page 14 - Installation; Safety instructions; Fixing to the supporting structure
Installation 16 5 Installation 5.1 Safety instructions Veneers, adhesives or plastic coatings on adjacent furniture should be temperature-resistant ( >90°C ), otherwise they might warp over time. The minimum clearances must also be respected for the edges of the hob on the back as indicated in th...
Page 15 - Make the seal stick to the edge around
Installation 17 EN To prevent leakage of liquid between the frame of the hob and the work surface, carefully put the insulating seal provided in position before assembly.1. Refer to the dimensions in the figure, bearing in mind that the front and rear long sides must brush against the hole. 2. Make ...
Page 16 - Gas pipe connection; Over empty kitchen unit or drawers
Installation 18 Gas and electrical connection location (measurements in mm - view from the top) Gas pipe connection Electrical connection 5.3 Mounting Over built-in oven The clearance between the hob and the kitchen furniture or other installed appliances must be enough to ensure sufficient ventilat...
Page 17 - General information
Installation 19 EN It must only be possible to remove the double-layer base using suitable equipment. opens on bottom 5.4 Gas connection General information This appliance is suitable for installation with Natural Gas or ULPG (propane/butane). Refer to “Burner and nozzle characteristics tables” para...
Page 18 - The regulator must be fitted to the 1⁄2
Installation 20 Connection of the appliance to the gas supply must be in accordance with the requirements of AS5601. A ½” BSP connector at the inlet is recommended and the gas supply line to the appliance must be of adequate length to allow sufficient withdrawal of appliance for service or disconnec...
Page 19 - Room ventilation
Installation 21 EN Room ventilation The appliance should be installed in rooms that have a permanent air supply in accordance with the standards in force. The room where the appliance is installed must have enough air flow for the regular combustion of gas and the necessary air change in the room it...
Page 20 - Adaptation to different types of; Changing the nozzles
Installation 22 5.5 Adaptation to different types of gas In case of operation with other types of gas, the burner nozzles must be changed and the minimum flame adjusted on the gas cocks. Changing the nozzles 1. Remove the grid from the hob. 2. Remove the flame-spreader crowns and relative burner cap...
Page 21 - Light the burner and turn it to the minimum
Installation 23 EN Adjusting the minimum setting for natural or town gas 1. Light the burner and turn it to the minimum position. 2. Remove the knobs by pulling them upwards. 3. Turn the regulating screw on the side of the cock stem until a steady minimum flame is achieved. 4. Refit the knob and ver...
Page 22 - Burner and nozzle characteristics tables; Electrical connection
Installation 24 Burner and nozzle characteristics tables The nozzles not provided are available at Authorised Service Centres. 5.6 Electrical connection General information Check the mains characteristics against the data indicated on the plate.The identification plate bearing the technical data, se...
Page 23 - Fixed connection; Instructions for the installer; DO NOT
Installation 25 EN Fixed connection Fit the power line with an omnipolar circuit breaker in compliance with installation regulations. The circuit breaker should be located near the appliance and in an easily reachable position. For stationary appliances permanently connected to the fixed wiring, com...
