Smeg CIR60X - Manuals - manualsarea.com

Page 2 - Index; INSTRUCTIONS FOR THE INSTALLER: these are for the; authorised; who must carry out a suitable check of the gas system, install

Index 1. INSTRUCTIONS FOR SAFE AND PROPER USE ________________ 4 2. POSITIONING OF HOB ____________________________________ 6 3. GAS CONNECTION ______________________________________ 11 4. ELECTRICAL CONNECTION ______________________________ 12 5. GAS CONNECTION _____________________________________...

Page 3 - Introduction; INSTRUCTIONS FOR SAFE AND PROPER USE

Introduction 1. INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE C...

Page 5 - Instructions for the installer; POSITIONING OF HOB

Instructions for the installer 2. POSITIONING OF HOB It is the law that all gas appliances are installed by authorised persons. Clearance around the appliance must comply with the requirements of AS5601. The following operation requires building and/or carpentry work so must be carried out by a comp...

Page 7 - Clearance above and around domestic appliances; REQUIREMENTS

Instructions for the installer 2.2 Clearance above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measurement A) Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance betwe...

Page 8 - NOTES; Requirement 3 does not apply to a freestanding or elevated

Instructions for the installer Where B, measured from the periphery of the nearest burner to any vertical combustible surface, is less than 200 mm, the surface shall be protected in accordance with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for the full dimension (width or d...

Page 9 - Room ventilation; for appliances not equipped with gas safety; Discharge of combustion products

Instructions for the installer 2.3 Room ventilation Caution – This hob may only be installed and operated in rooms permanently ventilated in accordance with current regulations. For proper operation of a gas appliance it is essential for the air necessary for combustion of the gas to be able to flow...

Page 11 - ELECTRICAL CONNECTION; Do not use reducers, adapters or shunts.

Instructions for the installer 4. ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same typ...

Page 13 - Connection to LPG

Instructions for the installer 5.1 Connection to LPG Use a pressure regulator and make the connection to the tank according to the provisions of standards regulations in force. Make sure that feed pressure conforms to the levels shown in the table in paragraph “6.2 Regulation for LPG”. 5.2 Ventilati...

Page 14 - ADAPTATION TO DIFFERENT TYPES OF GAS; Removing the hob; plates

Instructions for the installer 6. ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, detach the appliance from the electrical socket. The hob has been inspected for NG natural gas at a pressure of 1.0 kPa. For functioning with other types of gas the nozzles must...

Page 15 - Regulation for LPG

Instructions for the installer 6.2 Regulation for LPG Loosen screw A and push support B all the way. Use a double head wrench to remove nozzle C and assemble the suitable one, following the instructions indicated in the reference charts, with respect to the type of gas to use. The screwing torque of...

Page 16 - Regulation for natural gas; Regulation of minimum for natural gas

Instructions for the installer 6.3 Regulation for natural gas The hob has been adjusted for natural gas at a pressure of 1.0kPa. To allow the unit to work back with this type of gas, after it has been adjusted for LPG, perform the same operations described in paragraph “6.2 Regulation for LPG”, but ...

Page 17 - Arrangement of burners on hob; Lubrification of gas taps

Instructions for the installer 7.3 Arrangement of burners on hob BURNERS 1 Auxiliary 2 Semi-rapid 3 Rapid 4 Rapid 5 WOK 7.4 Lubrification of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-greased. This must be done by a qualif...

Page 18 - Instructions for the user; Some models do not feature all accessories.; Ignition of the burners

Instructions for the user 8. USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted correctly. In the ultrarapid burner, notch A must be aligned with pin B. Grid C provided is intended for use with woks (Chinese pans). Adapter D comes only with ...

Page 19 - Practical advice for using the burners; Auxiliary; Electric elements; on

Instructions for the user 8.2 Practical advice for using the burners For better burner performance and minimum gas consumption, flat bottomed, even recipients must be used, with covers and proportional in size to the burners (see paragraph “8.3 Diameter of containers”). To avoid overcooking or damag...

Page 20 - WARNING; Switch the electric element only after having placed the pan on it.

Instructions for the user 8.4.2 Using the electric elements The electric elements are ideal for ultrarapid cooking. The settings shown in the table are merely indicative. POSITION HEAT INTENSITY POSSIBLE COOKING 0 Off - 1 Weak To melt butter, chocolate, etc. To heat small amounts of liquid. 2 Soft T...

Page 21 - CLEANING AND MAINTENANCE; NEVER USE A STEAM JET TO CLEAN THE APPLIANCE.; Cleaning of cooking hob components

Instructions for the user 9. CLEANING AND MAINTENANCE Before any intervention, disconnect the power supply of the device. 9.1 Cleaning Clean the cooking top regularly every time you use it, obviously after it has cooled. NEVER USE A STEAM JET TO CLEAN THE APPLIANCE. 9.1.1 Regular daily cleaning of t...

Page 22 - Ignition plugs and safety devices; Preventive maintenance

Instructions for the user 9.2.1 Ignition plugs and safety devices For good functioning of the lighting ignition plugs and the safety devices, keep them very clean. Check frequently and clean with a damp cloth when necessary. 9.2.2 The cover Clean the glass or steel cover, where mounted, with warm wa...

Page 23 - PROBLEMS AND CAUSES; PROBLEM; Call Service Center.

Instructions for the user 10. PROBLEMS AND CAUSES Each of the following cases is caused by an abnormal operation of the appliance and should be dealt with by a authorised persons: please contact your local dealer or Service Center in case you detect any of these malfunctioning. PROBLEM CAUSE WHAT TO...