Shop Fox W1854 - User Manual

-9- Model W1854 (For Machines Mfd. Since 04/18) EL EC TR IC A L ELECTRICAL Circuit.Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is a...

-10- Model W1854 (For Machines Mfd. Since 04/18) EL EC TR IC A L Grounding.Requirements This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric sho...

-11- Model W1854 (For Machines Mfd. Since 04/18) SE TU P SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Description. Qty • Additional People .......

-12- Model W1854 (For Machines Mfd. Since 04/18) SE TU P Hex Wrench 16mm MEASURE BOL T DIAMETER BY PLACING INSIDE CIRCLE 7 ⁄ 16 " 3 ⁄ 8 " 1 ⁄ 4 " 5 ⁄ 16 " #10 1 ⁄ 2 " W ASHERS ARE MEASURED BY THE INSIDE DIAMETER USE THIS CHART TO IDENTIFY HARDWARE DURING THE INVENTORY/ASSEMBLY PR...

-13- Model W1854 (For Machines Mfd. Since 04/18) SE TU P Box.Contents.(Figure.2). Qty A. Main Sander Unit (Not Shown) ..........................1 B. Top Long Brackets .........................................2 C. Top Short Brackets ........................................2 D. Bottom Short Brackets ....

-14- Model W1854 (For Machines Mfd. Since 04/18) SE TU P Machine.Placement Weight.Load Refer to the Machine.Specifications for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on th...

-15- Model W1854 (For Machines Mfd. Since 04/18) SE TU P Assembly Before beginning the assembly process, refer to Items. Needed.for.Setup and gather everything you need. Ensure all parts have been properly cleaned of any heavy-duty rust-preventative applied at the factory (if applicable). Be sure to...

-19- Model W1854 (For Machines Mfd. Since 04/18) SE TU P Figure.14. Removing switch key from paddle switch. Test.Run Serious. injury. or. death. can. result. from. using. this. machine. BEFORE. understanding. its. controls. and. related. safety.information..DO.NOT.operate,.or. allow. others. to. ope...

-20- Model W1854 (For Machines Mfd. Since 04/18) O PE R ATIO NS OPERATIONS General To. reduce. your. risk. of. serious. injury. or. damage. to. the. machine,. read. this. entire.manual.BEFORE.using.machine. To. reduce. the. risk. of. eye. injury. and. long-term. respiratory. damage,. always. wear. s...

-21- Model W1854 (For Machines Mfd. Since 04/18) O PE R ATIONS Stock.Inspection.&. Requirements Some workpieces are not safe to sand, or they may require further preparation before they can be safely sanded without increasing risk of injury to the operator or damaging the sanding belt or the san...

-23- Model W1854 (For Machines Mfd. Since 04/18) O PE R ATIONS Adjusting.Conveyor. Feed.Rate The conveyor feed rate dial (see Figure 16 ) allows you to set the conveyor feed rate from 0–12 FPM. The correct speed to use depends on the type of stock you are using (hardwood vs. softwood) and the stage ...

-27- Model W1854 (For Machines Mfd. Since 04/18) O PE R ATIONS Changing.Sanding.Drum. Speeds This machine features two different sanding speeds, which are controlled by belt position on the pulleys (see Figure 23 ). IMPORTANT: Proper belt tension is important for optimum power transmission. Any time...

-28- Model W1854 (For Machines Mfd. Since 04/18) O PE R ATIO NS ACCESSORIES Sander.Accessories The following sanding accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also available through online dealers...

-29- Model W1854 (For Machines Mfd. Since 04/18) M A INTEN A N CE MAINTENANCE Cleaning the Model W1854 is relatively easy. Vacuum excess sawdust, and wipe off the remaining dust with a dry cloth. Cleaning.&.Protecting For optimum performance from your machine, follow this maintenance schedule an...

-30- Model W1854 (For Machines Mfd. Since 04/18) M A INTE N A N CE Figure 27 . Helical gear location. Figure 26 . Table lift screws (2 of 4). Table.Lift.Screws,.Chain,.&.Helical.Gears Oil Type .................................. NLGI#2 or Equivalent Oil Amount .......................................

-32- Model W1854 (For Machines Mfd. Since 04/18) M A INTE N A N CE SERVICE General A worn/damaged V-belt will not provide optimum power transmission from the motor to the drum belt. Inspect the V-belt closely; if you notice fraying, cracking, glazing, or any other damage, replace the belts. V-belt r...

-44- Model W1854 (For Machines Mfd. Since 04/18) SE RV IC E Electrical.Safety.Instructions SHOCK.HAZARD. Working on wiring that is connected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, o...

-45- Model W1854 (For Machines Mfd. Since 04/18) SE RV IC E ON/OFF Paddle Switch Ground Neutral Hot Ground 5-15 Plug 120VAC Overload Switch L1 Series 25A 125V KEDU HY56 TN40-55(JSC) Circuit Board Variable- Speed Dial Feed Belt Motor 90W 110V DC LINE LOAD Main Motor 1.5HP 120V 1-PH Motor Junction Box...

-46- Model W1854 (For Machines Mfd. Since 04/18) PA RT S PARTS Main.Breakdown 94 39 129 38 125 36 42 59 35 57 99 51 35 60 119 124 134 131 132 126 134 132 131 138 141 124 139 135 99 51 60 40 100 37 54 123 15 92 108 16 72 23 120 121 93 6 9 1 4 5 2 3 7 8 10 11 12 13 14 117 80 99 60 140 130 133 27 137 1...

WARRANTY Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neglige...