Page 3 - USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!; Contents
SE TU P EL EC TR IC A L M A INTEN A N CE SE RV IC E PA RT S O PE R ATIONS SA FE T Y IN TR O DUCT IO N USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST! INTRODUCTION...................................... 2 Woodstock Technical Support .................. 2 Machine Specifications ............
Page 4 - INTRODUCTION
-2- Model W1686 (For Machines Mfd. Since 11/10) IN TR O DU CT IO N INTRODUCTION Woodstock.Technical.Support This machine has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reli...
Page 5 - HP OSCILLATING SPINDLE SANDER
-3- Model W1686 (For Machines Mfd. Since 11/10) IN TR O DUCT IO N Model W1686 Machine Specifications, Page 1 of 2 MODEL W1686 1 HP OSCILLATING SPINDLE SANDER Product Dimensions Weight.......................................................................................................... 287 lbs. W...
Page 7 - Identification
-5- Model W1686 (For Machines Mfd. Since 11/10) IN TR O DUCT IO N Identification Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. For.Your.Own.Safety.Read.This.Manual.Before. Operating.Spindle.Sander a). Wear....
Page 9 - NOTICE; SAFETY
-7- Model W1686 (For Machines Mfd. Since 11/10) SA FE T Y Indicates.a.potentially.hazardous.situation.which,.if.not.avoided,. MAY.result.in.minor.or.moderate.injury. Indicates.an.imminently.hazardous.situation.which,.if.not.avoided,. WILL.result.in.death.or.serious.injury. Indicates.a.potentially.ha...
Page 12 - ELECTRICAL
-10- Model W1686 (For Machines Mfd. Since 11/10) EL EC TR IC A L Circuit.Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. ...
Page 13 - Grounding.Requirements
-11- Model W1686 (For Machines Mfd. Since 11/10) EL EC TR IC A L Grounding.Requirements This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric sho...
Page 14 - PADDLE SWITCH
-12- Model W1686 (For Machines Mfd. Since 11/10) EL EC TR IC A L Converting.Voltage.to. 240V The voltage conversion MUST be performed by an electrician or qualified service personnel. The voltage conversion procedure consists of rewiring the motor and installing the correct plug. A wiring diagram is...
Page 15 - TU; SETUP; Unpacking
-13- Model W1686 (For Machines Mfd. Since 11/10) SE TU P SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Items.Needed.for.Setup The following item...
Page 16 - USE THIS CHART TO IDENTIFY
-14- Model W1686 (For Machines Mfd. Since 11/10) SE TU P Hex Wrench 16mm MEASURE BOL T DIAMETER BY PLACING INSIDE CIRCLE 7 ⁄ 16 " 3 ⁄ 8 " 1 ⁄ 4 " 5 ⁄ 16 " #10 1 ⁄ 2 " W ASHERS ARE MEASURED BY THE INSIDE DIAMETER USE THIS CHART TO IDENTIFY HARDWARE DURING THE INVENTORY/ASSEMBLY PR...
Page 17 - Inventory
-15- Model W1686 (For Machines Mfd. Since 11/10) SE TU P Box.Contents.(Figures.8–10). Qty A.. Spindle Sander Unit (Not Shown) .......................1 B.. Sanding Spindles 1 ⁄ 4 " x 5" ......................................................1 3 ⁄ 8 " x 6" .................................
Page 19 - Electrical.Installation
-17- Model W1686 (For Machines Mfd. Since 11/10) SE TU P Figure.11. Working clearances. Machine.Placement 28 3 / 4 " 25 1 / 4 " Weight.Load Refer to the Machine.Specifications for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of ...
Page 20 - Assembly
-18- Model W1686 (For Machines Mfd. Since 11/10) SE TU P Assembly Before beginning the assembly process, refer to Items. Needed.for.Setup and gather everything you need. Ensure all parts have been properly cleaned of any heavy-duty rust-preventative applied at the factory (if applicable). Be sure to...
Page 24 - OPERATIONS; General
-22- Model W1686 (For Machines Mfd. Since 11/10) O PE R ATIO NS OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written w...
Page 25 - PE
-23- Model W1686 (For Machines Mfd. Since 11/10) O PE R ATIONS Stock.Inspection Sanding.Tips • Replace the sanding sleeve with a higher grit to achieve a finer finish. Avoid skipping grits, as this will leave scratches in the wood. • Extend the life of the sanding sleeve by regularly using a PRO-STI...
Page 29 - Finish Line
-27- Model W1686 (For Machines Mfd. Since 11/10) O PE R ATIONS Bevel.Sanding The Model W1686 has a tilting table to allow bevel sanding at a variety of angles. Bevel sanding on a spindle sander is NOT an exact science. When the table is tilted to 45˚, the actual angle sanded on the edge of a workpie...
Page 30 - ACCESSORIES
-28- Model W1686 (For Machines Mfd. Since 11/10) O PE R ATIO NS ACCESSORIES Spindle.Sander.Accessories The following Spindle Sander accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also available through...
Page 32 - MAINTENANCE
-30- Model W1686 (For Machines Mfd. Since 11/10) M A INTE N A N CE MAINTENANCE Cleaning the Model W1686 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it. Keep tables rust...
Page 33 - CE
-31- Model W1686 (For Machines Mfd. Since 11/10) M A INTEN A N CE Cleaning.Sanding.Sleeves As sanding sleeves are used, they will become "loaded" with saw dust. If not removed, this saw dust will harden on the abrasive surface, greatly reducing the effectiveness of the sanding sleeve. Routin...
Page 34 - Troubleshooting
-32- Model W1686 (For Machines Mfd. Since 11/10) SE RV IC E SERVICE Troubleshooting Motor.and.Electrical PROBLEM POSSIBLE.CAUSE CORRECTIVE.ACTION Machine does not start, or power supply breaker trips immediately after startup. 1. Switch disabling key removed.2. Power supply circuit breaker tripped o...
Page 36 - WIRING DIAGRAM COLOR KEY
-34- Model W1686 (For Machines Mfd. Since 11/10) SE RV IC E Electrical.Safety.Instructions SHOCK.HAZARD. Working on wiring that is connected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, o...
Page 37 - STOP
-35- Model W1686 (For Machines Mfd. Since 11/10) SE RV IC E Wiring.Diagram Neutral Hot Hot Hot Ground Ground PADDLE SWITCH (viewed from behind) Rewired to 240V Rewired for 240V G 5-15 Plug 120 VAC (Prewired) 240 VAC 6-15 Plug (As Recommended) Ground Start Capacitor 300uF 125VAC Ground Rewired for 24...
Page 38 - RT; PARTS; Main
-36- Model W1686 (For Machines Mfd. Since 11/10) PA RT S PARTS Main 95 76 77 99 96 71 70 107 45 22 108 8 111 86 110 34 111 33 33 32 107 26 109 23 28 29 28 99 99 99 99 100 30 101 27 25 19 18 114 113 79 97 64 2 20 30 31 31 112 103 92 35V2 35-1 105 104 106 78 83V2 76 15 95 16 90 90 92 75 80 102 92 7 91...
Page 43 - WARRANTY
WARRANTY Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neglige...
