Page 3 - USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!; Contents
SE T U P EL EC TR IC A L M A INTEN A N CE SE RV IC E PA RT S O PE R ATIONS SA FE T Y IN TR O DUCT IO N USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST! INTRODUCTION...................................... 2 Woodstock Technical Support .................. 2 SAFETY............................
Page 4 - INTRODUCTION
-2- Model W1740 (For Machines Mfg. Since 1/13) IN TR O DU CT IO N Woodstock.Technical.Support Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product. I...
Page 8 - NOTICE; Read manual Before Operating machine; SAFETY
-6- Model W1740 (For Machines Mfg. Since 1/13) SA FE T Y Indicates.a.potentially.hazardous.situation.which,.if.not.avoided,. MAY.result.in.minor.or.moderate.injury. Indicates.an.imminently.hazardous.situation.which,.if.not.avoided,. WILL.result.in.death.or.serious.injury. Indicates.a.potentially.haz...
Page 11 - ELECTRICAL
-9- Model W1740 (For Machines Mfg. Since 1/13) EL EC TR IC A L ELECTRICAL Circuit.Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is av...
Page 12 - Grounding.Requirements
-10- Model W1740 (For Machines Mfg. Since 1/13) EL EC TR IC A L Grounding.Requirements This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric shoc...
Page 13 - Unpacking; SETUP; Inventory
-11- Model W1740 (For Machines Mfg. Since 1/13) SE TU P This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Unpacking SETUP The following items are needed, but not in...
Page 16 - Handcrank.Installation
-14- Model W1740 (For Machines Mfg. Since 1/13) SE TU P The handcrank is installed on the front right lift screw shaft, and is held in place with two set screws already threaded into the handle. To mount the handcrank, place the handcrank over the shaft shown in Figure.7 and, using a 3mm hex wrench,...
Page 17 - Adjustments
-15- Model W1740 (For Machines Mfg. Since 1/13) SE TU P Once the assembly is complete, test run your machine to make sure it runs properly. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review the Troubleshooti...
Page 18 - OPERATIONS; General
-16- Model W1740 (For Machines Mfg. Since 1/13) O PE R ATIO NS OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written wi...
Page 20 - Requirements
-18- Model W1740 (For Machines Mfg. Since 1/13) O PE R ATIO NS Stock.Inspection.&. Requirements Some workpieces are not safe or may require modification before they are safe to sand. Before sanding, inspect all workpieces for the following: • Material.Type : This machine is intended for ONLY san...
Page 22 - Sanding
-20- Model W1740 (For Machines Mfg. Since 1/13) O PE R ATIO NS Figure.12. Variable speed knob. Variable.Speed The variable speed knob allows you to increase the feed rate from 2.47–17.3 FPM. The correct speed to use depends on the type of stock you are using (hardwood vs. softwood) and the stage of ...
Page 23 - Sandpaper.Replacement
-21- Model W1740 (For Machines Mfg. Since 1/13) O PE R ATIONS GRIT CLASS USAGE 36 Extra Coarse Rough sawn boards, thickness sanding, and glue removal. 60 Coarse Thickness sanding and glue removal. 80–100 Medium Removing planer marks and initial fin- ish sanding. 120–180 Fine Finish sanding. The Mode...
Page 24 - ACCESSORIES
-22- Model W1740 (For Machines Mfg. Since 1/13) O PE R ATIO NS ACCESSORIES Drum.Sander.Accessories The following drum sander accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also available through online...
Page 25 - MAINTENANCE; Cleaning; Schedule
-23- Model W1740 (For Machines Mfg. Since 1/13) M A INTEN A N CE MAINTENANCE Cleaning the Model W1740 is relatively easy. From time to time, vacuum wood dust off of the internal components, especially the motor. Cleaning For optimum performance from your machine, follow this maintenance schedule and...
Page 26 - Lubrication
-24- Model W1740 (For Machines Mfg. Since 1/13) M A INTE N A N CE Figure.18. Helical gear lubrication. Figure.16. Pillow bearing lubrication. Figure.17. Sprocket, lift screw, and chain lubrication. Lubrication Drive Chain Grease Fittings Lift Screw (1 of 4 Shown) An essential part of lubrication is ...
Page 27 - SERVICE; Replacing
-25- Model W1740 (For Machines Mfg. Since 1/13) SE RV IC E SERVICE This section covers the most common service adjustments or procedures that may need to be made during the life of your machine. If you require additional machine service not included in this section, please contact Woodstock Internat...
Page 33 - Tracking
-31- Model W1740 (For Machines Mfg. Since 1/13) SE RV IC E If the drum-to-conveyor tracking (see Figure.30 ) is off track by more than 1 ⁄ 8 ", you will have to adjust the track- ing. To.check.and.adjust.the.drum-to-conveyor.tracking,.do. these.steps: 1. DISCONNECT SANDER FROM POWER ! 2. First m...
Page 35 - Tension
-33- Model W1740 (For Machines Mfg. Since 1/13) SE RV IC E The pressure rollers are factory set at 0.080" (2mm) below the bottom of the sanding drum and are fully adjustable either up/down with the lower adjustment bolts (see Figures.36. and .37 ). After the adjustment has been made, always lock...
Page 49 - Electrical.Components; STOP
-47- Model W1740 (For Machines Mfg. Since 1/13) SE RV IC E Electrical.Components Figure.63.. Feed motor. Figure.65.. Capacitor. Figure.66.. Variable speed control and circuit board. Figure.64. Drum motor wiring. Figure.67.. ON/OFF switch wiring. STOP Read Page 46 Before Wiring
Page 51 - Frame; PARTS
-49- Model W1740 (For Machines Mfg. Since 1/13) PA RT S 28 12 2813-1 13 11-2 11-1 11 28 120 44 14-1 9 7-7 7-1 7-7 7-4 7-3 7-5 7-2 7-7 7-1 7-7 7-1 118 112 113 114 28 109V2 108 110 118 10 28 100 115 117 104A 107 102 103 4 4-1 5 7-7 28 3 1 2 16 16 17 18 21 23 19-1 20 23 45V2 31V3 56 121-1 121 28 52 52-...
Page 53 - Drum
-51- Model W1740 (For Machines Mfg. Since 1/13) PA RT S Drum 89-1 70 69 71 71 73 73 73 73 71 71 80 80 82 82 82 85 85 87 85 85 87 87 87 89-1 22 89 94 81 26 81 26 88 89 88 22 89 88 89 88 24 24 25 92 90 93 16 69 40 25 82 98 REF PART # DESCRIPTION REF PART # DESCRIPTION 16 XPSS03 SET SCREW 1/4-20 X 3/8 ...
Page 54 - Conveyor
-52- Model W1740 (For Machines Mfg. Since 1/13) PA RT S Conveyor 65-2 65-1 73 61 66 64-1 77 79 74 49-2 57-2 49-1 57-2 51-2V2 61 34 35 34 60 59 51V2 61 73 60 59 50V2 57-1 34 78 64V3 101 61 57-2 37V2 76 78 38V4 97 95 97 96 63 134 83 76 56V2 138 51-1V4 38V4-1 38V4-2 38V4-3 38V4-5 38V4-6 38V4-7 38V4-7 3...
Page 59 - WARRANTY
WARRANTY Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neglige...
Page 60 - High Quality Machines and Tools; to meet the needs of today's woodworkers and metalworkers.
High Quality Machines and Tools Woodstock International, Inc. carries thousands of products designed to meet the needs of today's woodworkers and metalworkers. Ask your dealer about these fine products:
