Shindaiwa 68002-94310 - Manual
Shindaiwa 68002-94310 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Contents; Attention Statements; Be aware of kickback!; Fuel Filler; OBTAINING WARRANTY SERVICE
- Page 3 – Before Operation; Never inhale exhaust gas.; Safety Precautions; PARTS COVERED; Ignition System Components; LIMITATIONS; service being performed, and; MAINTENANCE AND REPAIR REQUIREMENTS
- Page 4 – Starting The Engine; Federal Emission Design And Defect Limited Warranty; MANUFACTURERS WARRANTY COVERAGE
- Page 5 – Kickback; Operation; Troubleshooting
- Page 6 – Keep the unit away from children.; Stopping The Engine; Long Term Storage
- Page 7 – Safety and Operation Information Labels; Checking the Fuel Filter; Take the filter out from the fuel; Lubricating the Clutch Bearing
- Page 8 – Unit Description; Make sure the ignition switch is Off
- Page 9 – Technical Specifications; Replacing the Drive Belt; Loosen the two bolts in the clutch; Checking the Cut-off Wheel
- Page 10 – Assembly; Recommended Cut-off Wheels
- Page 11 – Filling the Fuel Tank; Examples of 50:1 mixing quantities; Adjusting the Carburetor
- Page 12 – Keep bystanders well away.; Starting the Engine; When the Engine is Cold; On; Cleaning the Air Cleaner
- Page 13 – Starting a Warm Engine; Keep well away from fire!; If the engine still does not start,; If the Engine Doesn’t Start; Stopping the Engine; Item; Inspection and Maintenance Requirements
- Page 14 – Wet or Dry Operation; Cutting; Make sure you have a clear work; Reversing cutting head for flush cutting operations
No perform
ance guaran
tee without u
sing
genuine Shin
daiwa blade
s.
No-load rev
olution spee
d: 4180 min
-1
(rpm)
Use reinforc
ed abrasive b
lades with m
aximum
useable perim
eter velocity
of 248 ft/se
c.
USE ONLY G
ENUINE
SHINDAIWA
BLADES
EC7500
Maximum b
lade diamete
r: 12 in.
Maximum b
lade thickne
ss: 0.16 in.
Arbor diam
eter: 1 inch
SHINDAIWA OWNER’S AND
OPERATOR’S MANUAL
EC7500/EC7600
ENGINE CUTOFF
SAW
WARNING!
■
Read this manual and familiarize yourself with its contents.
■
This unit is designed primarily for cutting construction materials and metal
according to the type of cutting wheel installed.
■
To minimize the risk of injury to yourself and others, always wear hearing
protection, a dustproof mask, goggles and a helmet when operating this unit.
■
Keep this manual handy so you can refer to it when required.
Part Number 68002-94310 Rev. 12/02
(EPA VERSION)
Shindaiwa Inc.
11975 SW Herman Road
Tualatin, Oregon 97062
Telephone 503-692-3070
Fax
503-692-6696
www.shindaiwa.com
Shindaiwa Kogyo Co., Ltd.
6-2-11 Ozuka-Nishi
Asaminami-Ku, Hiroshima
731-3167, Japan
Telephone 81-82-849-2220
Fax
81-82-849-2481
©2002 Shindaiwa Inc.
Part Number 68002-94310
Shindaiwa is a registered
trademark of Shindaiwa Inc.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Throughout this manual are special“attention statements”. WARNING! A statement preceded by the word“WARNING” contains informationthat should be acted upon toprevent serious injury. CAUTION! A statement preceded by the word“CAUTION” contains informationthat should be acted upon toprevent unit damag...
3 Before Operation ■ Children and people who do notunderstand this manual mustnot use this unit. ■ Never allow other people oranimals to be near the unitwhen starting or operating. ■ Never touch a rotating cut-offwheel. ■ Operate the unit only in a wellventilated area. ■ Never operate the unit in ac...
4 Safety Precautions (continued) WARNING! Figure 1. Start the engine at least 10 feet (3 meters) from a fueling location. Starting The Engine ■ Start the engine at least 10 feet(3m) away from a fuelinglocation. ■ When starting the engine,make sure the cut-off wheeldoes not touch any object orground....
